+ Reply to Thread
Results 1 to 10 of 10

Thread: No 4 & No5 Bolt Heads (Update)

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Alan de Enfield's Avatar
    Join Date
    Nov 2007
    Last On
    Today @ 05:50 AM
    Location
    Y Felinheli, Gogledd Cymru
    Posts
    2,526
    Real Name
    Alan De Enfield
    Local Date
    03-28-2024
    Local Time
    12:29 PM

    No 4 & No5 Bolt Heads (Update)

    As many of you will remember I have been compiling a spreadsheet of bolt head sizes for a few years now, and, now having the dimensions for 220 bolt heads I thought it was time for an update.

    As you will see (and has been stated on numerous occasions) it is no use at all simply saying "I need a Number 3 bolt head" when (for example) a 0.632" up to 0.636" bolt head can be a number 0, a number 1, a number 2 or a number 3.

    Tradition has it that the bolt head "numbers" fall within the following dimensions :
    0 - .620 to .625 in.
    1 - .625 to .630 in.
    2 - .630 to .635 in.
    3 - .635 to .640 in.

    I hope you can see from the spreadsheet that this is not necessarily correct.

    Note : I use the term "NUMBER" and not "SIZE".

    Disclaimer - these bolt heads have been measured by several people using different measuring 'tools'. There is no way that these statistics would be taken as 'accurate' for QC purposes but I believe they show enough guidelines for us to be very careful when we are buying a 'new' bolt head.

    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...

  2. The Following 13 Members Say Thank You to Alan de Enfield For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    eddystone3006's Avatar
    Join Date
    Nov 2011
    Last On
    10-18-2013 @ 10:15 PM
    Location
    McKean County, PA
    Posts
    13
    Local Date
    03-28-2024
    Local Time
    08:29 AM
    This information is more helpful than a door jam for an itchy back.

    The problem I have run into more than a few times is #1, #2, & #3 heads are hard to come by and when you do find them, there are no measurements provided.

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-28-2024
    Local Time
    02:29 PM
    Like I've said many, many times on this very forum, a bolt head NUMBER iosn't really indicative of a size but an estimation....... Many's the time a bolt with a size, say, 1 bolthead is undersize for CHS so you'd automatically try a size 2. But while this is how it SHOULD wotk, it doesn't necessarily. Try a few more size 1's or even a few size 0's and you'll find a few in the tray that will correct it. Obviously we had a big binfull of crack and hardness tested bolt heads.

    Another word of warning too........... Don't forget that changing a bolthead will also alter various other important features of a previously perfect bolt - such as overturn, lift, FPP as well as CHS

  7. Thank You to Peter Laidler For This Useful Post:


  8. #4
    Advisory Panel

    jmoore's Avatar
    Join Date
    Mar 2009
    Last On
    06-09-2023 @ 04:20 AM
    Location
    US of A
    Posts
    7,066
    Local Date
    03-28-2024
    Local Time
    08:29 AM
    Quote Originally Posted by Peter Laidlericon View Post
    Don't forget that changing a bolthead will also alter various other important features of a previously perfect bolt - such as overturn

    I'm wondering if overturn (i.e. bolt head rear face wear) would account for some of the variations in nominal size.

    Excessive overturn seems a more serious condition than a few thousanths more headspace.

  9. #5
    Legacy Member Alan de Enfield's Avatar
    Join Date
    Nov 2007
    Last On
    Today @ 05:50 AM
    Location
    Y Felinheli, Gogledd Cymru
    Posts
    2,526
    Real Name
    Alan De Enfield
    Local Date
    03-28-2024
    Local Time
    12:29 PM
    Thread Starter
    Quote Originally Posted by jmoore View Post
    I'm wondering if overturn (i.e. bolt head rear face wear) would account for some of the variations in nominal size.

    Excessive overturn seems a more serious condition than a few thousanths more headspace.
    From my limited knowledge 'bolt head overturn' will in fact lead to increased headspace as the 'threads' on the bolt head / bolt body take the hammering of the recoil (and compress) rather that the two flat surfaces of the bolt head and bolt body taking the load and passing it back down the bolt body to the locking lugs.

    With regard to "rear face wear" I would have expected that to make the bolt head 'shorter' whilst most of those measured tend to be longer that the expected norm.
    I can find no references to actual bolt head size in any of the 'official' books / booklets I have, all I have found (example "Parts Identification List" dated 1945) is that "No1 to No3 increase in length by increments of 0.003"" but no starting size is quoted.
    Last edited by Alan de Enfield; 02-08-2012 at 06:01 AM.
    Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...

  10. Thank You to Alan de Enfield For This Useful Post:


  11. #6
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-28-2024
    Local Time
    02:29 PM
    The PLAN size of the length of the bolt heads are
    No3 - 0.638" -.002"
    No2 0.635" -.002"
    No1 0.632" -.002"
    No0 0.629" -.002"

    You can see that even from this, if a, say, size 3 is made to the drawing spec, then it COULD easily be 0.636". As I said, we didn't take much notice of the number but might use it as a bit of a rule of thumb guide. Same as Bren or L1A1 locking shoulders

  12. The Following 2 Members Say Thank You to Peter Laidler For This Useful Post:


  13. #7
    Legacy Member Alan de Enfield's Avatar
    Join Date
    Nov 2007
    Last On
    Today @ 05:50 AM
    Location
    Y Felinheli, Gogledd Cymru
    Posts
    2,526
    Real Name
    Alan De Enfield
    Local Date
    03-28-2024
    Local Time
    12:29 PM
    Thread Starter
    Quote Originally Posted by Peter Laidlericon View Post
    The PLAN size of the length of the bolt heads are
    No3 - 0.638" -.002"
    No2 0.635" -.002"
    No1 0.632" -.002"
    No0 0.629" -.002"
    That makes sense -there are 'clusters' around those dimensions.

    I just wonder if some manufacturers (maybe Non-UK ones for example) had a slightly different 'start point' or worked to bigger tolerances or +/- tolerances.

    Is there a date on the document from which you have sourced this information, would it be possible that prior to this date there was a different specification ?

    Any suggestions why else there is such a wide disparity ?
    Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...

  14. #8
    Advisory Panel Thunderbox's Avatar
    Join Date
    Dec 2008
    Last On
    01-10-2022 @ 02:07 PM
    Posts
    1,150
    Local Date
    03-28-2024
    Local Time
    12:29 PM
    Quote Originally Posted by Alan de Enfield View Post
    Any suggestions why else there is such a wide disparity ?
    `

    Probably because the disparity in size actually helps fulfil the requirement - i.e. an armourer rummaging through his box of spares is likely to find a bolt head to fit without having to make any adjustments. I would not be at all surprised if this dimensional control was deliberately relaxed for this very reason; after all - other components are remarkably consistent between manufacturers and years and models - eg sears, triggers, pins and the corresponding dimensions of the action bodies.

    I guess the minimum number of rifles any armourer would be responsible for would be about 100 (ie a company or other sub-unit). Probably even at this level, the armourer would have thirty to fifty boltheads in his spares pack (there is probably a scaling document somewhere). I suppose I have about a hundred No4 boltheads, and find that I can get a perfect fit by trying about 15 to 20 (and I can even usually match the manufacturer as well in that size sample).

  15. #9
    Advisory Panel

    jmoore's Avatar
    Join Date
    Mar 2009
    Last On
    06-09-2023 @ 04:20 AM
    Location
    US of A
    Posts
    7,066
    Local Date
    03-28-2024
    Local Time
    08:29 AM
    Quote Originally Posted by Alan de Enfield View Post
    From my limited knowledge 'bolt head overturn' will in fact lead to increased headspace as the 'threads' on the bolt head / bolt body take the hammering of the recoil (and compress) rather that the two flat surfaces of the bolt head and bolt body taking the load and passing it back down the bolt body to the locking lugs.

    With regard to "rear face wear" I would have expected that to make the bolt head 'shorter' whilst most of those measured tend to be longer that the expected norm.
    Odd, that. Contrary to expectations!

  16. #10
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-28-2024
    Local Time
    02:29 PM
    This thread and the findings should be compulsory reading for every gunsmith, Enfield enthusiast and home tinkerer.

    Well done all concerned especially AdeE.

  17. Thank You to Peter Laidler For This Useful Post:


+ Reply to Thread

Similar Threads

  1. Bolt Heads are getting expensive!!!
    By Brian B in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 1
    Last Post: 10-20-2011, 12:58 AM
  2. Help! Source for Bolt Heads?
    By Minnesota Joe in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 10
    Last Post: 03-21-2010, 03:49 AM
  3. SMLE Bolt Heads
    By delta8672 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 7
    Last Post: 10-03-2009, 07:01 AM
  4. Size of #4 MK 1 Bolt Heads?
    By kscchtrainer in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 5
    Last Post: 08-27-2008, 06:04 PM
  5. Used Lee-Enfield Bolt Heads
    By Badger in forum Gunsmithing for Old Milsurps
    Replies: 0
    Last Post: 07-13-2008, 03:40 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks