+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 25

Thread: BSA commercial No1 MkIII Fultonised? - Any advice gratefully accepted yet again!.

Click here to increase the font size Click here to reduce the font size
  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    jss's Avatar
    Join Date
    Dec 2010
    Last On
    09-13-2019 @ 07:05 PM
    Location
    Oxfordshire, England
    Posts
    118
    Local Date
    03-29-2024
    Local Time
    01:27 AM

    BSA commercial No1 MkIII Fultonised? - Any advice gratefully accepted yet again!.

    Managed to get hold of this one last week and for those of you who are not fed up with questions from a novice, here goes;
    Attachment 31596Attachment 31595Attachment 31597Attachment 31598Attachment 31599Attachment 31600Attachment 31601
    1) Is there a way of dating this rifle?.
    2) Is the 632C prefix to the serial number a Fultons thing?.
    3) Is the cork packing in the front hand guard(which has bowed it) a Fulton modification or a DIY job?.
    4) The Forend is split (see pic) by someone removing the stock bolt without removing the forend. Does it need fixing?. It is very firm in the draws and the crack shows no movement, so I don't want to ruin it.
    5) The sear pivot/bolt head release spring screw was undone when I got the rifle. Should I "Tin" the threads to ensure it does not come loose again or is that unnecessary?.
    6) The sear has quite a lot of play as does the trigger about its pivot. Is it worth replacing sear , pivot screw and trigger pivot or is the play taken up when the cocking piece engages thus squaring things up?.
    7) The woodwork has a glossy finish. Should I keep it "As Is" or strip and oil it?.
    8) The P\ stamped on the action next to the BM Proof (pic 3)???.
    8) Where is the best (cheapest) place to get a Stock bolt and washer, safety washer, sear and screw etc.

    The barrel is well worn but looks clean and shiny with some rifling left although it does not spin the cleaning rod at all.
    So is this just a scrap rifle to be left "as is" for plinking or is it worth tidying up with a few new parts?.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-29-2024
    Local Time
    02:27 AM
    Just a comment on the barrel. It doesn't have to spin the cleaning rod, it's just got to impart spin (gyroscopic effect) to the bullet and I have seen some sniper barrels that just look shot out and accept the gauges that it should reject............. but they shoot as sweet as a nut. Years ago we'd just reject such barrels out of hand regardless of the fact that they shot well. Now we listen to the shooter. If it accepts the 'run' gauge and passes the accuracy test, then it's accepted.

    What I'm saying in a shaggy dog story way is to assemble the rifle up properly and range/accuracy test it. If it groups, that's good enough for me! A worn or shot-out leed is the arch enemy of accuracy

    I wouldn't accept a cracked fore-end. Easily repaired and will never improve with age! Same as worn axis pins. Some slack will be taken up with loading pressures but it's a palliative and not a cure and pi55 poor engineering practice to boot. Think excess end float on wheel bearings..........

    Just my 2p's worth

  4. The Following 3 Members Say Thank You to Peter Laidler For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Contributing Member
    bigduke6's Avatar
    Join Date
    Jul 2008
    Last On
    03-25-2024 @ 09:09 PM
    Location
    North West England,UK
    Posts
    3,279
    Local Date
    03-29-2024
    Local Time
    12:27 AM
    Jss,

    First thing I would do is see how it preforms on the range, then go from there, one thing regarding the glossy finish is this varnish or a build up of many years of linseed oilicon?

  7. Thank You to bigduke6 For This Useful Post:

    jss

  8. #4
    Deceased January 15th, 2016 Beerhunter's Avatar
    Join Date
    Dec 2007
    Last On
    01-02-2016 @ 04:03 PM
    Location
    Hampshire, England
    Posts
    1,181
    Local Date
    03-29-2024
    Local Time
    12:27 AM
    It's been "double proofed": Birmingham and Gunmakers Company (London).

    I can think of two reasons why this could happen. The first is that significant has been done to the rifle that needs to be proofed. However in your case, in think that someone did not "trust" the Birmingham Military Proof (BM) and erroneously, in my opinion, had it proofed again in London.

    As to date, the best that I can do is: "between the wars".

    It also seems to have some Government marks as well and is that two sets of serial number?
    Last edited by Beerhunter; 03-05-2012 at 12:14 PM.

  9. #5
    Advisory Panel
    Jc5's Avatar
    Join Date
    May 2008
    Last On
    02-23-2024 @ 12:54 PM
    Location
    West Coast, USA
    Posts
    203
    Local Date
    03-28-2024
    Local Time
    07:27 PM
    1) Is there anything stamped on the top-right rear, flat part of the action, where the bolt slides in?
    2) Anything stamped on the bottom of the barrel and action (where they meet)?
    3) Is there a crossed flag proof mark anywhere?
    4) On the butt socket, does it say "B.S.A. Co." ?
    5) Can you please post a picture of the entire rifle?

    Thanks!
    Last edited by Jc5; 03-05-2012 at 10:07 PM.
    .
    .
    Researching Lee Speeds and all commercial Lee Enfields. If you have data to share or questions, please send me a PM.

  10. #6
    Legacy Member Rowdy's Avatar
    Join Date
    Apr 2008
    Last On
    Yesterday @ 06:15 PM
    Location
    Australia
    Posts
    88
    Local Date
    03-28-2024
    Local Time
    07:27 PM
    Attachment 31629I think the P/ is part of an almost scrubbed out crossed flags proof.
    Packing the handgard was a common accurising technique and was probably Fulton's work.
    My Alex'r Henry has the same type of packing.
    The 632C type marking I have always assumed to be a government view mark (to certify that the rifle is mil. spec. and therefore able to be used in competition) but Wheaty recently said he was told by one of the Fultons that it was a Territorial marking - while the Fultons should know, I find it strange. Most of the BSA commercial target rifles that turn up in Australiaicon have these markings and are in too good condition to have been used by the military - although they often have another number on the top of the action which could be local military accounting but they seem to have been just stored in WW2.
    The original finish on these BSA rifles seems to have been a glossy varnish.Attachment 31628
    Last edited by Rowdy; 03-06-2012 at 02:20 AM.

  11. Thank You to Rowdy For This Useful Post:

    jss

  12. #7
    FREE MEMBER
    NO Posting or PM's Allowed
    jss's Avatar
    Join Date
    Dec 2010
    Last On
    09-13-2019 @ 07:05 PM
    Location
    Oxfordshire, England
    Posts
    118
    Local Date
    03-29-2024
    Local Time
    01:27 AM
    Thread Starter
    Thanks Rowdy and jc5icon.
    I have another 232E prefix. I'll dig them both out and take some photos rather than try and describe the marks. There are loads of them!.
    Yes it's BSA and Co on the Butt socket, there are marks on the rear flat of the action A and T and more on other surfaces including A on the underside of the action next to the barrel with ^84 above ^57 ^51 ^57 and another mark on the reinforce and a P further down the barrel???.
    Much easier to see when the sun shines!.

  13. #8
    FREE MEMBER
    NO Posting or PM's Allowed
    RJW NZ's Avatar
    Join Date
    Aug 2008
    Last On
    10-04-2014 @ 11:58 PM
    Location
    Auckland NZ
    Posts
    1,241
    Local Date
    03-28-2024
    Local Time
    05:27 PM
    Quote Originally Posted by jss View Post
    Managed to get hold of this one last week and for those of you who are not fed up with questions from a novice, here goes;
    Attachment 31596Attachment 31595Attachment 31597Attachment 31598Attachment 31599Attachment 31600Attachment 31601
    1) Is there a way of dating this rifle?.
    2) Is the 632C prefix to the serial number a Fultons thing?.
    3) Is the cork packing in the front hand guard(which has bowed it) a Fulton modification or a DIY job?.
    4) The Forend is split (see pic) by someone removing the stock bolt without removing the forend. Does it need fixing?. It is very firm in the draws and the crack shows no movement, so I don't want to ruin it.
    5) The sear pivot/bolt head release spring screw was undone when I got the rifle. Should I "Tin" the threads to ensure it does not come loose again or is that unnecessary?.
    6) The sear has quite a lot of play as does the trigger about its pivot. Is it worth replacing sear , pivot screw and trigger pivot or is the play taken up when the cocking piece engages thus squaring things up?.
    7) The woodwork has a glossy finish. Should I keep it "As Is" or strip and oil it?.
    8) The P\ stamped on the action next to the BM Proof (pic 3)???.
    8) Where is the best (cheapest) place to get a Stock bolt and washer, safety washer, sear and screw etc.

    The barrel is well worn but looks clean and shiny with some rifling left although it does not spin the cleaning rod at all.
    So is this just a scrap rifle to be left "as is" for plinking or is it worth tidying up with a few new parts?.
    Aha, another Fultons rifle, very nice, a desirable rifle for sure, worn or not, and as others have said, how it shoots is the deciding factor, especially now when barrels are not so easily found.
    I like triggers to be tighter on their pivots than loose, and even though they are made loose if you rummage in a box if them you can get a pivots and parts match that are tighter than most. I'm not sure about parts in the UKicon but there are several good suppliers in the USAicon ie Numrich who ship outside the US, there's a list of them in enfieldresource.com.
    What kind of barrel bedding does your rifle have? The Fultons I have here uses spring damping with a small section of cork at the front of the top guard, its always interesting to see what the pros were deciding worked best.
    Your exterior finish looks just like mine, and correct.
    re screws and dotting them, not needed, these two don't tend to come undone, I'd say they probably weren't tightened at the last look in.
    The only comment I'll toss in is that cork bedding and packing especially, and probably also others such as cardboard, compress over time, and it was usual to firm up their contact with the barrel once per year at least by adding another thin layer of packing, even .005 of paper would do it, so if you want to try improving its shooting try that trick of making the packing tight on the barrel. The way you know that the packing thickness is correct is that when the guard is resting on the rifle but not clamped by the bands there should be a small gap between the guard and the forend, about 1 mm or 1/32inch would do it. This will compress as the bands are done up, applying the right pressure.
    cheers, nice rifle, well done.
    Last edited by RJW NZ; 03-06-2012 at 03:47 PM.

  14. #9
    Legacy Member Frederick303's Avatar
    Join Date
    Aug 2008
    Last On
    07-28-2020 @ 09:41 PM
    Location
    Pipersville PA US
    Posts
    739
    Local Date
    03-28-2024
    Local Time
    08:27 PM
    Gents,


    Of the Fulton regulated rifles I have seen them fall into three categories as far as modifications:

    1) Pre 1934, no metal shields or added actions screws. Fitted asbestos pad under the forearm and cork hand guard packing. Packing varies enough on rifles, some are full hand guard, some are only jut forward of the rear band and over the nose cap area, sufficient to keep the barrel from resting against the top of the nose cap on the two “nubs”
    2) Post 1934 to ~WWII period, added metal band between nose cap and rear band to ensure constant pressure on upper hand guard packing. Lower packing material more likely to be cork then asbestos. Also the nose cap on these rifles is reamed out so that the barrel is not contacting at any point.
    3) Post 1950 rifles that have the above as well as an added weld on the front of the action body, and four screws mounted to maintain the action body alignment within the forend. On these rifles it is not uncommon to see the top packing replaced by small metal plungers to exert downward force on the barrel. The plungers have small spring mounted to maintain pressure.

    The above is only the barest guide, based on what I have seen in guns located in the US of A and Canadaicon. The nice thing about rifles seen here is they generally retain whatever Fulton features they were made with, rather then having been updated over their match career. In particular after 1946~47, these rifles were not legal for Canadian competition so they were bought and used for Bisley teams and quite a number of post war guns are in pretty good shape on this side of the pond.

    Unfortunately that can not be said of the pre war Alex Martin, AG parker, AJ Parker and Parker-Hale rifles, most of which seem to have been sported or altered in some other way (sigh). In any case my observations are based on examining the rifles that show signs of match regulation and seem to have some date indications.

    The earliest guns that were packed (circa 1924) were only packed in the top hand guard. This seemed to help with the accuracy but was seen as finicky, sometimes “packing up” in the middle of a competition due to heat. These guns also seem to have an action body stamp like yours with just a “G Fulton”, they do not say “regulated by Fulton” as do the later rifles.

    Sometime in the late 1920’s the idea of putting in pads of asbestos in the locations where the barrel contacted the forend was introduced, along with lubricating the sliding surfaces. This was supposed to help with vertical group shifts as the barrel heated up.

    An alternative method that is seen in rifles left in Canada was placing pads of cork above and below the Nodes of the barrel, in an effort to dampen the vibrations of the barrel. This seems to have been the Alexander Martin method and was somewhat popular in the new world because of the relative ease with which a rifleman could regulate his own rifle (by copying the Alex Martin techniques).

    Sometime in the late 1920s to the early 1930s Fulton’s regulation of rifles seems to have moved their rifles into the winners circle and there they remained for most of the remaining 303 period (up to 1968) at least in the UKicon. Fulton seems to have blazed a trail with regards to action welding to help with action alignment, adding plugs on the forend to align the action body with the stock, adding plungers on the top hand guard instead of packing and replacing the asbestos pads with rubberized gasket cork

    The problem with identifying when a rifle was regulated (especially with English rifles) is that these rifles were used and had their packing and regulation periodically updated. On the rifles I have been allowed to examine the owners typically date the rifles to earlier than the Birmingham proof allow. Foe example I have seen a heavy barrel BSA gun that the owner is sure was pre war, when the Bisley bibles I have clearly state the BSA heavy barrel was not allowed until the summer of 1950. His father may have bought it earlier, and used it earlier, but he heavy barrel dated from 1952-1953

    As for the gun described in the above, what would be of help is to see the forend packing, if any. Also a pic of the forend internals where the action body lays would be indicative. If there is packing in the forend that would date it to circa 1928 or later. The stamp is a Fulton trade proof and I have seen that one early guns. It is possible that the rifle was packed by someone other then Fulton’s, that was common in the 1920s or so I have read.

    Also you can date the barrel if you can locate the BSA proof date mark. That would be small crossed swords with a letter above the handles of the swords if pre WWII. The dates stated at A which correlates to July 1921 to June 1922, C correlates to 1923/24, etc. I think I or J might have been left out.

    Post war the crossed swords will have a letter combination on either side of the crossed swords like (BB -1951), BC -1952, etc. London will have no such date mark though.

    No idea if Fulton had any rifles proofed at London, it is closer to Bisley but most of the post WWII guns I have seen seem to have been proved at Birmingham.

    Those are the first things that come to mind. The added numbers are from their internal register. Unfortunately those records were taken By Robin Fulton when he sold the firm; they seem to have been destroyed when he died. What a huge loss.

    Hope that helps

  15. The Following 9 Members Say Thank You to Frederick303 For This Useful Post:


  16. #10
    FREE MEMBER
    NO Posting or PM's Allowed
    jss's Avatar
    Join Date
    Dec 2010
    Last On
    09-13-2019 @ 07:05 PM
    Location
    Oxfordshire, England
    Posts
    118
    Local Date
    03-29-2024
    Local Time
    01:27 AM
    Thread Starter
    Thanks RJW NZicon and Frederick303. What a great response. From what you say, I think this is an early one. No asbestos thankfully or I would have had to bag it up and dispose of it!.
    I will strip the other one (after donning my Frog suit and setting up an air sampler), a MkIII which may or may not be a Fultons job, to check against this one and thentry to improve my photography skills.

+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. 1927 Colt Commercial - Advice needed
    By HoosierNative in forum 1911/1911A1 Service Pistol
    Replies: 1
    Last Post: 02-13-2012, 10:46 AM
  2. Fulton type No1 MkIII BSA commercial Target Rifle - What do I look for?
    By jss in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 9
    Last Post: 07-28-2011, 06:04 AM
  3. Newbie Needs Advice On 1927 Lithgow No.1 MKIII Rifle
    By traindriver in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 4
    Last Post: 07-24-2010, 06:36 AM
  4. No32 MkIII advice needed
    By OxfordAndy in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 0
    Last Post: 06-10-2010, 04:49 AM
  5. My only M1 rifle …”EMcF” accepted…and some other stuff.
    By drm2m in forum M1 Garand/M14/M1A Rifles
    Replies: 9
    Last Post: 04-08-2009, 08:09 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks