Search:

Type: Posts; User: M1Riflenut; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    13
    Views
    19,414

    I have an SA 5.32 T2 NM rifle that has a 10/53...

    I have an SA 5.32 T2 NM rifle that has a 10/53 LMR barrel. The rifle and barrel appear like new.

    https://www.milsurps.com/images/imported/2012/02/P10604241-1.jpg
  2. Even if it was an original USGI SA NM at one...

    Even if it was an original USGI SA NM at one time, it is not original anymore. More likely it is an SA Inc NM rifle as Phil posted above. As far as its real world value, you probaby overpaid a bit....
  3. Replies
    3
    Views
    6,144

    Is it an "old" garand or one of the SA inc...

    Is it an "old" garand or one of the SA inc garands?
  4. Replies
    6
    Views
    6,878

    It's been awhile but I had no problems with him...

    It's been awhile but I had no problems with him when I dealt with him.
  5. Replies
    9
    Views
    8,748

    My Eddystone M1917. It was sporterized but...

    My Eddystone M1917. It was sporterized but luckily they did'nt mess with the barrel or receiver which where in like new condition. Mostly it had a hacked up stock with no handguards and a modified...
  6. Replies
    28
    Views
    10,051

    I'm still here but not as often as the past....

    I'm still here but not as often as the past. Mainly a quick browser now. Too many websites and not enough time...............
  7. Replies
    6
    Views
    7,515

    Interesting. It looks ok to me on the base,spring...

    Interesting. It looks ok to me on the base,spring and pin but that aperture sure looks like a cast replacement, possibly that is why the pin hole is peened on one side, to hold the pin back in after...
  8. Replies
    2
    Views
    6,207

    Seek help with WRA stock marking

    Guys I have this posted on several sites for maximum response as time is critical.

    Looking for some input as to the marking on a M1917 stock I am considering buying. I've looked at many 1917...
  9. Replies
    7
    Views
    7,892

    Interesting,seeing as Winchester serial numbers...

    Interesting,seeing as Winchester serial numbers started at 100K :confused:

    Maybe it was 130K?
  10. Replies
    3
    Views
    11,843

    I respectfully disagree with half of your...

    I respectfully disagree with half of your statement.:)
    I have had several old used milsurp rifles that would not close on the go gauge,and with perfectly clean chambers. Granted,it's not common,but...
  11. Thread: 38 snubnose

    by M1Riflenut
    Replies
    9
    Views
    5,133

    Have you tried asking Colt? I thought they had a...

    Have you tried asking Colt? I thought they had a research/history dept.?
  12. Replies
    3
    Views
    5,283

    Sounds like it came from an Anniston rebuild. HRA...

    Sounds like it came from an Anniston rebuild. HRA stocks are available should you desire to get one.
  13. Replies
    32
    Views
    21,121

    This event was open to ANY GCA member that wanted...

    This event was open to ANY GCA member that wanted to go. Granted,there were a limited number of spaces available but ANYONE could have sent in there reservation and hoped for the best,same as when...
  14. Replies
    8
    Views
    7,927

    Slow forums on all sites,its a "summer" thing....

    Slow forums on all sites,its a "summer" thing. Add to that the fact that there are more websites to visit now so folks split up their time between them. There was a time when I only read CSP and...
  15. Replies
    32
    Views
    21,121

    :nono::crying:

    :nono::crying:
  16. I can change that spring in one minute. Try...

    I can change that spring in one minute. Try it,you'll like it.:thup:
  17. Replies
    4
    Views
    13,680

    +1 :thup:

    +1 :thup:
  18. Replies
    6
    Views
    6,698

    So many authors,so many answers...... I'll...

    So many authors,so many answers......
    I'll probably get some flak for this but the latest Poyer/Riesch book is probably the best to start out with for a quick referance easy to learn guide,but I...
  19. Replies
    14
    Views
    10,159

    Cass is correct and his scans also show something...

    Cass is correct and his scans also show something that has been the source of more than a few arguments over the years. That argument is that the early collector grades were not mint rifles,they were...
  20. I've seen floorplates bent like that before. I've...

    I've seen floorplates bent like that before. I've also seen stocks worn/compressed on the bottom at an angle to give the same appearance as a bent floorplate.

    Be aware that there are many dealers...
  21. Replies
    6
    Views
    5,952

    This is what its for. ...

    This is what its for.

    https://www.milsurps.com/images/imported/2009/09/P1070208jpgt1252633275-1.jpg
    https://www.milsurps.com/images/imported/2009/09/P1070195jpgt1252633407-1.jpg...
  22. Replies
    20
    Views
    28,929

    I love my carbines and AR's but they stay in the...

    I love my carbines and AR's but they stay in the safe. A loaded 12 ga and .45 are my boogeyman go to's. :)
  23. Replies
    8
    Views
    7,880

    Interesting that it is made up of two pieces...

    Interesting that it is made up of two pieces bolted together. I would'nt think that is as accurate as a solid machined part yet would cost more to build??
  24. Replies
    6
    Views
    8,146

    Does'nt Roland use Obermeyer barrels?

    Does'nt Roland use Obermeyer barrels?
  25. Replies
    22
    Views
    22,766

    Not meaning to hijack John's thread but have any...

    Not meaning to hijack John's thread but have any of you ever seen any SA M14 demilled receivers? I've been looking for a rear section SA M14 for a long time,seems like no one has them. If anybody has...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4
Milsurps Talk Radio