+ Reply to Thread
Results 1 to 9 of 9

Thread: Remington Rolling Block- Restoration Possible?

Click here to increase the font size Click here to reduce the font size
  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    Midmichigun's Avatar
    Join Date
    Sep 2010
    Last On
    01-10-2017 @ 10:06 PM
    Location
    Michigan
    Posts
    459
    Local Date
    03-28-2024
    Local Time
    12:38 PM

    Remington Rolling Block- Restoration Possible?

    Greetings from Michigan!

    I am not sure if this particular rifle was a "milsurp" itself, but I do know that various models and rifles of this type were used in America's frontier during the 1800's, and were ordered up to WWI for military use (mostly rear echelon) as I recall. The Rollingblock was a long time favorite of many S. American country's.

    Without further discussion, here is what I believe to be a #5, 1897 Remington Rollingblock as "recovered".





    If I do restore this rifle, it will be a long term item, due to the $$ for the parts. I am looking at Green Mountain 45-70 barrels, and have found a company that sells NEW Rollingblock parts.

    The current barrel has little value, 'cept to look at the caliber it was originally issued as.

    I believe the hammer and trigger could be salvaged along with the receiver. I would obviously opt for a new set of springs, breech block and barrel for starters.

    You can see where the previous owner "ovaled" out some of the screw holes.


    As of right now, I have it soaking in penetrating fluid and diesel fuel.


    Thanks for looking at my latest "tomato" stake!
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    Midmichigun's Avatar
    Join Date
    Sep 2010
    Last On
    01-10-2017 @ 10:06 PM
    Location
    Michigan
    Posts
    459
    Local Date
    03-28-2024
    Local Time
    12:38 PM
    Thread Starter
    The overall measurement of the barrel is this:

    Nice long barrel on that one! I am also thinking that this might be a Type 1 receiver. I have done some work to clean up the oval holes. Basically, I will either plug with steel and weld, or completely weld through. I did find bits of an old drill bit....

    I did need to drill out the pins that held the hammer and breech block. This gave me the following:

    A lot of careful soaking and work got me the following.... the removal of the barrel shank.


    ---------- Post added at 07:55 PM ---------- Previous post was at 07:50 PM ----------

    What I find interesting about the tang, is this set of holes:

    I am not a Remy Rolling expert, so I don't know if this was factory... or a field modification. To my untrained eye, it appears that one holes is off center. Is this for a tang mounted sight??
    It appears that the stock lug on the barrel was broken (aside from the rust).

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    07:38 PM
    I very seriously recommend that you search the forum for "electrolytic cleaning". While this rifle looks like a hopeless case, electrolytic cleaning will recover many parts well enough that they can be used as templates for making new parts. And you will discover an instance of a hopeless case RB being restored to shooting condition if you search for "Argentineicon Rolling Block"

  6. #4
    FREE MEMBER
    NO Posting or PM's Allowed
    Midmichigun's Avatar
    Join Date
    Sep 2010
    Last On
    01-10-2017 @ 10:06 PM
    Location
    Michigan
    Posts
    459
    Local Date
    03-28-2024
    Local Time
    12:38 PM
    Thread Starter
    Patrick,
    Well... thanks for the kind words!
    This is my test case.... if this works out, I will be converting a Beaumont model 1871 to 45-70govt (BP of course) also. You have to start somewhere, and I figure the Remy that I purchased, is perfect!
    I have a 2nd Remy that was given to me by my father. It is in somewhat better shape.... so I do have a way to check and verify dimensions when in a pinch.
    Looking the parts over, the only concern that I have is the breech block and extractor. Since the block takes sooo much force... and the extractor since it would be fragile after all these years! Worst case scenario is to reweld the severe pits in the metal and remill to correct specs!

  7. #5
    FREE MEMBER
    NO Posting or PM's Allowed
    joem's Avatar
    Join Date
    Mar 2009
    Last On
    03-01-2016 @ 08:56 PM
    Posts
    208
    Local Date
    03-28-2024
    Local Time
    11:38 AM
    To me that looks like a $$$$ undertaking, although not impossible. I have a Danishicon RB made in 1882 that I shoot quite a bit. I use Trail Boss powder instead od PB.

  8. #6
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    07:38 PM
    Quote Originally Posted by Midmichigun View Post
    Looking the parts over, the only concern that I have is the breech block and extractor.

    That is one very good reason to use electrolytic cleaning. It will clear out all the most minute holes in a way that you cannot achieve with abrasive methods. Fine abrasive/hard polishing methods can also hide hair cracks by the microscopic metal flow on the surface (which is part of a polishing/burnishing action) "papering over" the cracks. The block and hammer components take a battering, and the original hardened surfaces are probably rusted away. So these components may need to be replaced - or refaced !

    But before we get into that, give everything you can an electrolytic cleaning - it's really dead easy and cheap AND effective.

  9. #7
    FREE MEMBER
    NO Posting or PM's Allowed
    Midmichigun's Avatar
    Join Date
    Sep 2010
    Last On
    01-10-2017 @ 10:06 PM
    Location
    Michigan
    Posts
    459
    Local Date
    03-28-2024
    Local Time
    12:38 PM
    Thread Starter
    Patrick,
    Yes, the plan is to actually weld some new metal onto the worst of the pitting, including the breech block, if I can't find a new one. I will go with some nice quality rod to do this. My only concern is putting a case hardened finish onto the surface.

    I might have a contact in the "spray metal" field, and I will know in a few days if I can cultivate this resource to add metal to the outside of the receiver, breech block and trigger and hammer. These guys repair shafts for us at work.... A nice buildup would give me something to mill down. As mentioned, there are NO cartouches or marks left.... so destroying history is not a problem on this sucker...

    I am also looking at a barrel from these folks:
    BCPR - Black Powder Cartridge Rifle Barrels
    While I am thinking of BPCR type shooting with the rifle (so traditional 45-70 and 50-70 type loads would be nice), the .257 barrel fits my price range... As you can appreciate, I am concerned about pressures in this ole gal... but using a modern 4130 steel barrel will help with hoop stress.....
    Thanks for your patience and kind words!!

  10. #8
    FREE MEMBER
    NO Posting or PM's Allowed
    Midmichigun's Avatar
    Join Date
    Sep 2010
    Last On
    01-10-2017 @ 10:06 PM
    Location
    Michigan
    Posts
    459
    Local Date
    03-28-2024
    Local Time
    12:38 PM
    Thread Starter
    Guys,
    Well, after much welding, building up the surface, I have this:

    You will notice in the above photo, I need to fill in the edge of the receiver with more weld. However, most of the pits are gone, with the exception of some minor ones.

    This is a good example of the edge that needs to be filed down, to remove the deeper pits. I will put the trigger guard in place to finish this area off.

    Mind you that these are pre polish. I am told that if I case harden, I will need to polish... polish... polish... the surface.

    I am also looking to get this engraved if possible... before I case harden.

    I am still unsure of the caliber to select. I have noticed some "Star Rollingblock" barrels at Numrich. I think that the threads are different, and only share the name of Rollingblock. But the prices are better than if I go with 45-70govt.

  11. #9
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Today @ 10:51 AM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-28-2024
    Local Time
    12:38 PM
    Some years ago I rebarrel/restock a Rem 1902 rolling block that was in 7mm and sporterized, I used the Numrich 45-70 oct barrel and made a tang sight.

    My father had a 43 cal Rem rolling-block in his basement for years, came from Hunters lodge in the late 50's, NRA poor condition. I re-worked this over by starting with the receiver, I milled off the half dovetail edges and made it square, bent the lower tang for a pistol grip, made a bushing that I could change in the breech for center or
    rim fire. Best of all, I made a trigger with a sear for a nice trigger pull. I was given a blank of Calif walnut which I used to make the butt and forearm.

    There is a company that sells parts: Rolling Block Parts but expensive. I can not post photos so send me an email for photos

  12. Thank You to RCS For This Useful Post:


+ Reply to Thread

Similar Threads

  1. Rolling block project finished.
    By Claven2 in forum Black Powder
    Replies: 8
    Last Post: 06-02-2012, 09:33 PM
  2. Replies: 0
    Last Post: 12-29-2011, 03:51 PM
  3. Replies: 0
    Last Post: 12-29-2011, 03:48 PM
  4. Rolling Block and Barrel ? need opinions
    By Doug Rammel in forum Black Powder
    Replies: 3
    Last Post: 06-16-2011, 07:07 PM
  5. Remington Model 4 Rolling Block Rifle
    By Pattern14 in forum The Watering Hole OT (Off Topic) Forum
    Replies: 6
    Last Post: 06-02-2010, 06:37 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks