HELP TO ID M1 PARTS

Hello fellows.

Its me again, would you help me to ID the slide, trigger house, stock, and hand guard pls. The hand guard and slide dont have any marks.
Thank you in advance.

Regards
Eddie :beerchug:

Trigger housing is NPM. The other pictures are too small for any identification, at least for me. The slide will most likely be marked on the inside. You may need a magnifying glass and light it from an angle to be able to see the marking in the tooling marks.

Eddie,
It doesn't cost any more for bigger pictures. If your Camera has a little Flower symbol (Macro) use that setting.

I think I see Rear Beveled lug on the trigger housing
A .U. Underwood straight hammer.
Op slide appears (?) to have the M2 clearance cut on the right. But I don't see any numbers on he bottom.
2 Rivet Hand Guard that has a home made retaining tab. And appears to have letters on the bottom.
Rear sight a Type III fabricated.

Stock is too far away for details. Also can't see sling well markings. Only know it's a Oval cut and currently a low wood.
Easier to Play- Where's Waldo.

Eddie, you are getting the right idea but still too small, we are all old and lazy.

El Huevon

Dave, speak for yourself! I'm old, lazy, half deaf and half blind! But I can still shoot. Shot a 25 straight at skeet last night!

Quote:

---

Originally Posted by jimb16

Shot a 25 straight at skeet last night

---

Sure these Stiff Winds didn't bust a few ? :D

If you had heard the concussion from my shotgun, you might think that broke them! (Just kidding) I was using a 20 ga. with reduced shot loads! BTW that is far from the first 25 straight I've shot. Lost count after it got up into the double digits. I'm not bad with a pistol or rifle either and I've medaled in the Nationals with the carbine too. (Camp Perry) There are plenty of guys who are better than I am, but I still ain't bad!

Quote:

---

Originally Posted by jimb16

Trigger housing is NPM. The other pictures are too small for any identification, at least for me. The slide will most likely be marked on the inside. You may need a magnifying glass and light it from an angle to be able to see the marking in the tooling marks.

---

Thank you Jim
I will follow your advice
Eddie :beerchug:

Quote:

---

Originally Posted by painter777

Eddie,
It doesn't cost any more for bigger pictures. If your Camera has a little Flower symbol (Macro) use that setting.
I think I see Rear Beveled lug on the trigger housing
A .U. Underwood straight hammer.
Op slide appears (?) to have the M2 clearance cut on the right. But I don't see any numbers on he bottom.
2 Rivet Hand Guard that has a home made retaining tab. And appears to have letters on the bottom.
Rear sight a Type III fabricated.
Stock is too far away for details. Also can't see sling well markings. Only know it's a Oval cut and currently a low wood.
Easier to Play- Where's Waldo.

---

Hola Carlito,
Im a rookie with cameras too lol, I will try it in Macro mode but I think that its a Milsurps matter to save space in the website.
In the hand guard that reteainig tab is a black tape just to improve the union with the receiver.
Eddie :beerchug:

Quote:

---

Originally Posted by DaveHH

Eddie, you are getting the right idea but still too small, we are all old and lazy.

El Huevon

---

Hola Dave,
Cool mexican slang :super:

---------- Post added at 01:33 PM ---------- Previous post was at 01:30 PM ----------

Quote:

---

Originally Posted by jimb16

Dave, speak for yourself! I'm old, lazy, half deaf and half blind! But I can still shoot. Shot a 25 straight at skeet last night!

---

Lol :dancingbanana: