gravityfan, I suggest a good session with either boiled linseed oil or raw linseed oil, inside and out. I learned for myself about how oddly the wood can deform as it drys out and shrinks. There maybe a little fiddling to be done afterwards.
Brad
Printable View
gravityfan, I suggest a good session with either boiled linseed oil or raw linseed oil, inside and out. I learned for myself about how oddly the wood can deform as it drys out and shrinks. There maybe a little fiddling to be done afterwards.
Brad
I would like to add a little the Bradtx posting, if you are an American much of our Boiled Linseed oil is toxic due to chemical additives. Canadian and British BLO is not toxic because it is still made the old fashion way by actually heating or boiling the oil.
For the Americans here in our forum if you go to a Craft Store you can buy oil painting grade raw linseed oil and BLO that is non toxic that is strained and purified. (will not cause mold growth)
Below, this is 100% pure raw linseed oil that you will find in the oil painting area and is non toxic and can be applied bare handed.
https://www.milsurps.com/images/impo...nseedOil-1.jpg
Linseed Oil
Finest quality purified alkali refined linseed oil, for us with artists’ oil colors. Improves flow, increases gloss. This product may be added directly to Artists Oil Color. It is recommended linseed oil be pre-diluted with Pure Gum Spirits of Turpentine, Grumtine™, or Odorless Paint Thinner.
Below, Stand Oil is real actual Boiled Linseed oil, and is also non-toxic and won't make your genitalia fall off if applied by hand. :rolleyes:
https://www.milsurps.com/images/impo...tandoil1-1.jpg
Stand Oil
Polymerized linseed oil made by heating pure linseed oil to high temperatures in the absence of air. High-viscosity, non-yellowing. Intended for use with oil painting mediums, as well as diluted with conventional solvents. Improves fluidity of paint and assists in laying down (smoothing out) brush strokes. Slow drying and improves dry paint film flexibility. May be diluted with any conventional oil painting solvents.
And thanks to Bradtx for the back up posting on oiling the stock.. ;)
https://www.milsurps.com/images/impo...phstexas-1.gif
Finally an accurate map, Ed! :beerchug:
Brad
Ever mindful of Mr. Horton's warnings on US produced Boiled Linseed Oil, yesterday I stumbled across a reasonably priced (about US$8) quart can of BLO that has NO "evil" additives! Even their MSDS is good, so no worries.
Just thought it might prevent a bit of sticker shock if you have ever seen what the "artsy" oils retail at.
Made by Klean-Strip in Knoxville, TN, which I reckon is a good thing.
Link below:
http://www.kleanstrip.com/
To find the Linseed Oil, go to their products button, then choose the "thinners and solvents" button.
Mr. jmoore
"Artsy" raw linseed oil found at craft stores are highly refined linseed oils that have all impurities and fatty acids removed, these impurities and fatty acids are what causes mildew and mold growth.
These "artsy" linseed oils were never applied to the Enfield rifle while in military service. BUT they do come in small little itsy bitsy bottles and are handy to use. Also these artsy little itsy bitsy bottles would even fill the need of the fussy Michelangelo types when painting the Sistine Chapel or re-oiling an Enfield stock.
https://www.milsurps.com/images/imported/deleted.gif
On top of this Boiled Linseed oil was NEVER used on the Enfield Rifle, as a side note I also have manuals from the 1970s stating that RAW linseed was used on the American M14 and BAR rifles.
Trust me, during my excessive compulsive linseed oil testing phase, Clean Strip BLO was investigated, researched and NEVER mentioned in any of my postings.
Please show me any British or Commonwealth Enfield manual or publication where you are told to use Boiled Linseed Oil on your Enfield rifle.
https://www.milsurps.com/images/imported/deleted.gif
You don't put boiled linseed oil in a heated hot dip tank without this oil turning into a thick Jello like substance.
The majority of bedding problems our Enfield rifles have is because they were not re-oiled monthly with RAW linseed oil and the wood shrank as the wood dehydrated.
The untouched Enfield below went through a FTR in 1953 and had raw linseed oil applied to it and NOT BLO.
https://www.milsurps.com/images/impo...IMGP6641-1.jpg
The dark spots (freckles) you see were caused by the impurities in the raw linseed oil, the "artsy" oil will not let this happen because it is so highly refined and filtered.
https://www.milsurps.com/images/impo...IMGP6638-1.jpg
https://www.milsurps.com/images/impo...IMGP6633-1.jpg
The Clean Strip BLO will seal the wood and make it more water proof than RAW linseed oil, BUT it will need to have the shine knocked down with 0000 steel wool. Using BLO will make it far harder to apply successive coats of linseed oil that will sink deeply into the wood and keep it hydrated.
Below and forgive the small photo, pure raw unfiltered cold pressed linseed oil on the left with the impurities laying in the bottom of the jar. On the right is refined and filtered raw linseed oil with ALL the impurities removed. (the "artsy" linseed oil)
https://www.milsurps.com/images/impo...tein_oil-1.jpg
The above message was brought to you by the Society for the Prevention of Cruelty to Enfield Rifles.
I'm sorry Ed, but I think you are mistaken in this. I see no evidence whatsoever in the majority of rifles that bedding problems are the result of wood shrinkage from lack of oil or other agent. In fact I rarely see much evidence of wood shrinkage at all - on the contrary, its remarkable how many very old rifles have incredibly tight stock fit. Enfields were of course stocked using naturally seasoned or kiln-dried wood, thus the wood was de facto pre-shrunk anyway. In fact one of the properties of Linseed oil is that it appears to soak wood without causing any expansion or structural alteration. IMHO, bedding problems most commonly arise from wear and tear (especially in the draws) or poor maintenance.Quote:
Originally Posted by Edward Horton
ThunderboxQuote:
Originally Posted by Thunderbox
What you see on your side of the pond is quite different from what I have seen the last six years studying Century Imports on this side of the pond.
If you don't keep the wood properly oiled it WILL shrink and I can say this for curtain from looking a what I believe were primarily Enfield rifles coming from Turkey that never had a British Armourer lay hands on them.
My wooden deck and the Imported Enfield rifles I carefully inspected and looked at tell no lies.
Below, when wood dries out it shrinks as the gaps in my wooden deck show below.
https://www.milsurps.com/images/impo...riedwood-1.jpg
Also when you re-oil the fore stock and the draws area tightens up this also tells me something.
Thunderbox I mean no disrespect in what I said above but there is a good chance we are both right in our findings of the Enfields we have looked at.
My main point here Thunderbox is you should oil the stock with raw linseed oil BEFORE deciding the stock is a loose fit and before making bedding adjustments. As an example cork sheets under the barrel tip or bedding your Enfield with beer cans and credit cards when oiling the stock just might fix your problems.
https://www.milsurps.com/images/impo.../119ufm8-1.jpg
Below is a 1950 unissued Canadian Long Branch rifle I purchased from Brian Dick, it has a slight wood shrinkage problem. The first thing I'm going to do is give the stock a long drink of raw linseed oil before even thinking about shimming any part of the draws.
https://www.milsurps.com/images/impo...IMGP0921-1.jpg
Raw linseed oil will re-hydrate the dry wood in the stock and cause the wood to swell or enlarge.
Ed, great map and remember many many years ago we had a battle with our now "best friends" and burned your White House. Thankfully you did forgive us for this but I constantly hear you had a plan to invade Canada during the 60' thur the 90's. Would that mean you would have invaded yourselves first?
:lol:
Actually enfield303t that is a rumor the Canadian Government started to cover your own covert Canadian plans for invading the United States. Please look at the map below, all areas marked with a red Tim are now considered Canadian territory. (half the north east U.S. has been taken over)Quote:
Originally Posted by enfield303t
https://www.milsurps.com/images/impo...09091900-1.gif
https://www.milsurps.com/images/impo...mhortons-1.jpg
We Americans are not fighting to regain this territory because the coffee and donuts are sooooo good.
(your beer ain't half bad either) ;)
Ed you are the first to notice what we have been doing for the last few years. My inside information is that once we get you and all your American buddies "hooked" on Tim's we are going to give you the ultimatum to "surrender" or we will "cut off" all your coffee and donughts. Now that it is in the open we will have to change our plans drastically. :beerchug: