What...like all of it at once? You got a Minimi?
Printable View
What...like all of it at once? You got a Minimi?
Be a bit carefull with that Norinco .223.
The stuff that I've got over here and other stuff I've seen has all been extremly hot.
We've gone through thousands of that out here in Victoria. No problems.
Spent some quality time with a buddy's AR, my angle grinder and my Dremel, today. Cut the FSB, bayonet lug, and delta ring off and ground down the leftovers to allow a FF handguard to fit over top.
https://www.milsurps.com/images/impo...cc9a7131-1.jpg
https://www.milsurps.com/images/impo...550ee214-1.jpg
Finally got a chance to take some more pics and do some shooting with my new CMMG Conversion Kit....I gotta say, THIS THING IS AWESOME :bow:
Some more pics of The Bushmaster......
ARMS Front Flip
Attachment 40463Attachment 40464
Magpul MS2(Upgrading to MS3) and sling adapters
Attachment 40472Attachment 40471Attachment 40470Attachment 40469
Eotech 512 + 3x Magnifier
Attachment 40468Attachment 40467Attachment 40466Attachment 40465
MI Low pro Rear flip
Attachment 40473Attachment 40474
The CMMG Kit....
Attachment 40462
Attachment 40476
Used this Barska scope for the 22 kit. I hadn't shot it with 5.56 yet so I figured I'd use it for the .22....It has Illuminated .223 BDCR, a quick adjust turret from 100-500 yards and about a 4in eye relief that I absolutely love:madsmile:.
Attachment 40477
After initial adjustments, no further adjustments made between the 5, 5 shot groups
Attachment 40479
Likes the Mini Mags the best so far, only had 10 left though...
Attachment 40480
Doesnt seem to like the 36gr although they started to group tighter after the first 5-7 shots..
Attachment 40481Attachment 40482
The 5 to the left were definitely me...I'll find out for sure tomorrow it was getting dark and I had already been in the 10 deg weather for 2hrs straight :D, seems to group decent at 50yds non the less :thup:
Attachment 40478
Will be sighting this Tasco in tomorrow. I will be looking for som type of QD mount for it and another red dot eventually.
Attachment 40475
[QUOTE=Stevo;252477]Spent some quality time with a buddy's AR, my angle grinder and my Dremel, today. Cut the FSB, bayonet lug, and delta ring off and ground down the leftovers to allow a FF handguard to fit over top.
I couldn't "tap" my pins out so I ended up milling them out on the bridgeport :madsmile:, just because I had to show it who was boss. I should have done it your way, it would have been a lot faster after spending all that time trying to tap them out
In all honesty, I would have preferred to drive the pins out and reshape the FSB off the barrel. The Norinco ARs have incredibly tight pins, however. I've read lots of reports of guys ruining steel punches and even failing to get the pins out using hydraulic presses. We did take a few whacks at them with a BFH and they didn't move a fraction.
We could also have cut the FSB off and gone with a clamp-on or set-screw gas block, but my buddy was on a budget and the pinned gas block is superior, IMO, to either the clamp or set-screw gas block.
Looks like you're getting good results with the CMMG kit. Are you able to find enough .22LR to feed it?
I also think the cut down FSB is better than anything you can buy. Having tried the alternatives several times, I finally accepted that "Bubba'd" is better than store bought. :madsmile: