Printable View
i've been offered both in 110 grn fmj rn. is there any reason to prefer one over the other?
from what i've been able to discover Privi seems to get the nod with many saying that the Aguila is dirty and under powered. though not everyone seem to feel this way.
tia.
FWIW I've fired both brands. One carbine digests Aguila fine the other not so much with stovepipes and not so great accuracy. Both ran fine with Privi with no disenable difference in accuracy.
Either work well in most carbines. Aguila is somewhat lower powered, but it is accurate. If you reload, either will provide you with good cases for reloading. I've shot both and have no problem with either.
It's Prvi. There is no vowel between the R and the V. That said, it's First-rate ammo
It's Russian (Serbia) made. I can find American ammo just for GP.
Aguila tends to run fine in mine. I get a stove pipe every 50-60 rounds but that's it. I won't say it's dirtier than PPU but I will say the cases tend to be dirtier when they come out of the action suggesting they aren't expanding and sealing like the PPU (or Federal for that matter) but I don't know if it's from a lighter charge in general that it does to a lot of people or if it's due to it not sealing enough for my chamber. Brass cleans up great for reloading though. Groups seem good on both though I can't say if POI changes much between the two as I don't recall ever shooting them side by side at 100 but I'm getting it ready for a shoot so I might check that later this week. I tend to shoot Aguila as it's what I can get locally but from here on out I'll probably shoot reloads for awhile until I wear out/lose the 300-400 pieces of brass I have now.
thanks for the input guys. looks like the Pervi Partizan wins on points.
I use a lot of PRVI in different calibers and a lot of Aguila in different calibers. Both make fine ammunition, but since I no longer shoot .30 Carbine, I won't be testing either one of those. I have a few hundred rounds of PMC .30 Carbine left from 25 years ago if I get the itch to shoot the carbine every few years. Otherwise it just sleeps. BTW, for AK shooters, PRVI has 7.62X39 in round nose/soft point - looks like a pistol bullet. It loads fine and shoots about to the same point at 50 yds as anything else. Seems like it would make a pretty good HD round.
Every once in a while surplus ammo shows up at CMP. I buy what I can afford at the time, 2 to 4 cans, and it usually lasts until it becomes available again.
https://www.milsurps.com/images/impo...fab30733-1.jpg
I've used both too and have never had an issue other than the smell of the Aguila when it goes off. If I had a choice between the two I would take the Prvi pretty much every time though as I believe it's at least a slightly better ammo. Another advantage to Prvi is lately the price of it has come slightly down to around 22 dollars for a box of 50. I have seen it closer to Sellier and Bellot territory in the 30 dollar range.
U.S. ammo - always what to use in a U.S. firearm. :)Quote:
Originally Posted by JimF4M1s
Speaking of PP, I bought a thousand rounds of .308 for my RRA AR-10 and none of them would chamber correctly. After lots of head scratching, I found the casing necks to be slightly bulged, apparently when the bullets were pressed in. Ended up selling them to a guy with a lever-action Marlin. When we met for the sale, he had to slightly force the lever, but once he did, that round chambered fine every time. Weird! Anyone else seen this?
Russ
It was the crimp that did it. You need to be careful with crimping due to case neck swelling. If the dies got out of adjustment at the factory, the crimp could have gotten a bit too deep causing that problem. Not something that is likely to be noticed immediately.
I have had that problem with a batch of ammo I reloaded. The Lee Factory Crimp Die crushed it too much, and would not chamber. I thought it might be case length, but it did it to both ends of the spectrum. I went back to a roll crimp, with just a hint of factory crimp.
As for Aguila, it is purposely loaded under-powered to about 150 to 200 FPS less than Remington Factory or USGI. I find it works better if you use a degraded (weaker) recoil spring that is under 9.75" inches long. (New is 10 1/4"). It stopped stove pipes, but wouldn't load from a 30 round magazine that was close to full. I also had to switch to the 200 on the rear sight to bring the slower Aguila rounds up to the same POA of Remington on 100/150.