Search:

Type: Posts; User: jamie5070; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    17
    Views
    512

    How does it compare to the bayonet used on the...

    How does it compare to the bayonet used on the 1870's argentine rolling blocks?
  2. Replies
    53
    Views
    1,118

    You may have to apply heat to the sight base and...

    You may have to apply heat to the sight base and then place a piece of hard wood against it and rap it with a hammer. Shoot it first.
  3. Thanks for posting that. It makes me need to ID...

    Thanks for posting that. It makes me need to ID the timed fuse I have as a paper weight. I've always wanted to know what it went on. My fuse is more pointed than those you usually see in pictures....
  4. Replies
    1
    Views
    219

    How does the other bolt gauge in the rifle? What...

    How does the other bolt gauge in the rifle? What is the condition of the rifle and does the bolt appear to date with it? Do you have any other older 30-06 rifles with which to compare fired cases...
  5. Replies
    6
    Views
    273

    A worn mag spring?

    A worn mag spring?
  6. Replies
    5
    Views
    586

    The sights are normally soldered on. A little...

    The sights are normally soldered on. A little heat applied with a propane torch will allow the old sight to be removed. Then buy or make a new one. Tin the bottom of the sight. Hold it in place with...
  7. Replies
    9
    Views
    3,930

    they pop up on ebay too

    they pop up on ebay too
  8. Replies
    12
    Views
    1,393

    And then you need a canadian marked bayonet to go...

    And then you need a canadian marked bayonet to go with it. :)
  9. Replies
    8
    Views
    977

    I was going to do the same at one time , but the...

    I was going to do the same at one time , but the prices on the DP'd rifles started going up and I gave up on the idea. I still have a p-14 take off barrel stashed some where.
  10. Replies
    13
    Views
    1,274

    Try asking down on the 1903 forum. That said, If...

    Try asking down on the 1903 forum. That said, If the serial # has been scrubbed, I would strip it for parts.
    john
  11. Replies
    25
    Views
    2,778

    The MK IVs generally are in better condition than...

    The MK IVs generally are in better condition than the MK IIs. There is a man over on the britishmilita website that sells brass formed from magtech brass shotgun shells that are much cheaper than ...
  12. Replies
    11
    Views
    2,112

    There are peep sights that mount on the rear area...

    There are peep sights that mount on the rear area of the martini. Some people have made their own by having a side strap that attaches to the side with a piece that sits across the rear of the...
  13. Replies
    11
    Views
    2,112

    I wouldn't waste my money on the project. Ask...

    I wouldn't waste my money on the project. Ask over on the britishmilitaria website. They can give you the low down on the nepalese rifles. If I were going to build a .303 I would use a good british...
  14. Replies
    12
    Views
    1,413

    Could be a Bannerman Special. I doubt the barrel...

    Could be a Bannerman Special. I doubt the barrel is original. I have a spencer 3 band rifle that has what appears to be a trapdoor barrel on it. The rear sight dovetail is close to the action, like...
  15. Replies
    2
    Views
    820

    Even has a stripe on the upper stock

    Even has a stripe on the upper stock
  16. Replies
    42
    Views
    2,641

    You could do a cut and splice under one of the...

    You could do a cut and splice under one of the barrel bands if your daring enough
  17. You might try asking on the britishmilitaria...

    You might try asking on the britishmilitaria pistol forum. Someone there should be able to help you out
  18. Replies
    10
    Views
    2,284

    There is a person on the britishmilitaria website...

    There is a person on the britishmilitaria website who sells 24ga brass formed and ready to go.
  19. Replies
    12
    Views
    855

    Is there some kind of marking by the rear tang...

    Is there some kind of marking by the rear tang screw? Is the rear sight marked with regular numbers or some kind of scribble? My thought at looking at the pictures is that the rifle was one of the...
  20. I'm thinking that maybe there was some hard...

    I'm thinking that maybe there was some hard fouling that someone couldn't get out and they put some steel wool on a rod and chucked it in a drill.
  21. Replies
    7
    Views
    570

    What is more important is, What is the condition...

    What is more important is, What is the condition of the bore! With a 1919 dated remmington barrel, I would expect it to be in great shape. I can't make out how many digits in the serial #. Around...
  22. Replies
    17
    Views
    2,131

    You should do a you-tube video of it in use

    You should do a you-tube video of it in use
  23. Replies
    21
    Views
    1,262

    I thought I read somewhere that early machine gun...

    I thought I read somewhere that early machine gun crews had body armor.
  24. Replies
    3
    Views
    1,288

    What does a new replacement barrel from criterion...

    What does a new replacement barrel from criterion or CMP run? When consider in gun smithing costs, Are you saving a little or a lot on the used barrel.
    I have two original take off barrels and...
  25. Replies
    10
    Views
    5,422

    Maybe he has a problem with critters coming up...

    Maybe he has a problem with critters coming up through the drains. Those gaters can get nasty.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4
Gunonline.com