Search:

Type: Posts; User: pisco; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    211

    hi i have never crimped any 303 reloads ( they...

    hi i have never crimped any 303 reloads ( they all seem to shoot good
  2. Replies
    7
    Views
    406

    hi i have heard of these conversions but that is...

    hi i have heard of these conversions but that is the first one i have seen taking note of the rear sight elevation ramp it was set up for mk6 ammunition i could handle something like that in my...
  3. Replies
    10
    Views
    2,272

    View Post

    hi you done well wth the 24 g shells iím just glad we have bertram brass
    now you are ready to go what do they shoot like
  4. hi a old bloke showed me how to fix this problem ...

    hi a old bloke showed me how to fix this problem
    remove the dove tail block in the front of the breach block and fit a new dove tail block you will have to file fit and redrill the firing pin hole...
  5. i hope you mean take the forend off first then...

    i hope you mean take the forend off first then the butt
  6. Replies
    26
    Views
    1,646

    hi in the movie not without my daughter,one of...

    hi in the movie not without my daughter,one of the iranian tribesmen has a no5
  7. Replies
    11
    Views
    717

    hi if it helps there is a bloke in queens land...

    hi if it helps there is a bloke in queens land that is converting 303s to pistol cartridges had a look at one at the toowoomba gun show
  8. Replies
    5
    Views
    586

    View Post

    hi iím not real good at soldering but yes it is the correct way
  9. Replies
    5
    Views
    586

    without seeing your sight a mate had a martini...

    without seeing your sight a mate had a martini that the front was butchered we shaped up a new sight and wrapped the barrel in a wet rag and a bloke tig welded it on
  10. Replies
    5
    Views
    586

    hi how does the brass go with just neck sizing...

    hi how does the brass go with just neck sizing after the first firing,another option is to set the barrel back one thread i had a smle years ago that was hell on brass set the barrel back one thread...
  11. Thread: early carbines

    by pisco
    Replies
    17
    Views
    1,115

    hi englishman did you make the forend caps on the...

    hi englishman did you make the forend caps on the top 3 carbines
  12. Replies
    12
    Views
    602

    hi i have fixed a few of them cracks i pull the...

    hi i have fixed a few of them cracks i pull the stock bolt keeper out clean every thing up degrease the wood and get glue in the crack and i glue the keeper in as well never had a problem i use...
  13. Replies
    16
    Views
    964

    hi has the smle been sent to australia after ww1...

    hi has the smle been sent to australia after ww1 is the a ftr stamp on the left hand side wrist
  14. Thread: early carbines

    by pisco
    Replies
    17
    Views
    1,115

    hi very nice should have been chasing them years...

    hi very nice should have been chasing them years ago
  15. Replies
    21
    Views
    1,237

    hi i tested my cast bullets today they worked a...

    hi i tested my cast bullets today they worked a treat ,i have shot the bsa with ex mil ammo and it wasnít as accurate as my cast loads
  16. Replies
    21
    Views
    1,237

    hi found a bullet mould that i lapped out to...

    hi found a bullet mould that i lapped out to 321Ē i have made a dummy round and it chambers so i will load them up and see how they go 15 gr ar2205 should be a good starting load
  17. Replies
    21
    Views
    1,237

    hi i have a bsa smle with a lithgow barrel that...

    hi i have a bsa smle with a lithgow barrel that measures .318# the barrel is in very good condition i have been told to try paper patching a cast projectile i have the gear to do it just need the...
  18. Replies
    31
    Views
    2,085

    a lot of blokes carried a lucky penny my pop...

    a lot of blokes carried a lucky penny my pop carried one for years
  19. Replies
    77
    Views
    17,101

    View Post

    hi thatís not good there is a market for these wood sets i would love to be able to set up to make them
  20. Replies
    77
    Views
    17,101

    hi southern cross militarized in queensland sell...

    hi southern cross militarized in queensland sell new wood sets for smles
  21. Replies
    200
    Views
    121,143

    Sticky: hi muffett is all this info telling you what you...

    hi muffett is all this info telling you what you want
  22. Replies
    200
    Views
    121,143

    Sticky: hi a couple more for your list 1915 -25179 ...

    hi a couple more for your list

    1915 -25179 111-mag cut off
    barrel replaced

    1917-60242. 111mag cut off
    4md-13836. butt marked 10/18
    barrel replaced

    1942 -d53390 AF
  23. Replies
    23
    Views
    1,156

    View Post

    donít right it off it is repairable
  24. Replies
    18
    Views
    983

    hi i would keep it batch some brass to the rifle...

    hi i would keep it batch some brass to the rifle and enjoy
  25. Replies
    23
    Views
    1,156

    hi all i do to remove the old finish is spray the...

    hi all i do to remove the old finish is spray the wood with oven cleaner leave for 15 minutes and wash off with a old toothbrush hang in the sun to dry if there are any repairs to do now is the time...
Results 1 to 25 of 50
Page 1 of 2 1 2
AGI