Search:

Type: Posts; User: browningautorifle; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 5 1 2 3 4

Search: Search took 1.01 seconds.

  1. As in...the Norinco 305? They had chu wood...

    As in...the Norinco 305? They had chu wood stocks or black plastic, not walnut, birch or USGI fiberglass like these. Those guys wouldn't be changing them, or even maintaining as illustrated.
  2. There's also M16s at top, could these all not be...

    There's also M16s at top, could these all not be from LL program?
  3. If you go over to SMG forum and search you'll...

    If you go over to SMG forum and search you'll find lots of discussion on Sten, also more answers likely. https://www.milsurps.com/showthread.php?t=63927&highlight=sten
  4. I asked about that too, the threads inside will...

    I asked about that too, the threads inside will be different to anything inside the imperial version. When I converted an Ishy to CDN I had to refinish the existing FH and use it...
  5. That cut into my sciatic nerve and didn't let me...

    That cut into my sciatic nerve and didn't let me sit long.
  6. Replies
    8
    Views
    154

    I'd avoid any liquids at all, as they likely will...

    I'd avoid any liquids at all, as they likely will stain. At best a bit of scuffing to remove rust? Don't want to dirty up the surrounding area.
  7. Always knew they were good for more than digging...

    Always knew they were good for more than digging sand and washing...
  8. Replies
    17
    Views
    506

    Doesn't need much of a scrub, shoot it little and...

    Doesn't need much of a scrub, shoot it little and then clean and see?
  9. Replies
    8
    Views
    154

    Not too much to stop aging except perhaps a bit...

    Not too much to stop aging except perhaps a bit of careful rust removal. The cost? If Kerr No-Buckle sling is $100 these must be all of that? These are even more rare?
  10. Replies
    13
    Views
    409

    Like...the inexperienced doing a barrel job?

    Like...the inexperienced doing a barrel job?
  11. Replies
    8
    Views
    176

    A small drift poked in and tap with a machinist...

    A small drift poked in and tap with a machinist hammer. You'll be able to get the mag catch out by prying the plunger back with a big jeweller's screwdriver. Then tap the stuck plunger and it'll...
  12. No, you should be able to post something here,...

    No, you should be able to post something here, whether on forum or in your profile...



    I had two, one as issued and one was a parts gun, shooter. No bayonet lug and trashed stock. I sold it...
  13. Replies
    8
    Views
    176

    Just invert the carbine and look at the witness...

    Just invert the carbine and look at the witness hole underneath the trigger mech. You'll see how the mag catch is held in. Or you could look for a vid... Watch this one from the two minute mark.
    ...
  14. Those should be ballistic tip and I think Hornady...

    Those should be ballistic tip and I think Hornady if you have a look...
  15. Replies
    15
    Views
    460

    We have a couple of those here too, one a bit...

    We have a couple of those here too, one a bit recent and one I think was RVN time. Maybe they can help...as well.
  16. So, how about a picture heavy photo thread on...

    So, how about a picture heavy photo thread on this one? Maybe a range report...
  17. Not really, the durakote doesn't obscure like a...

    Not really, the durakote doesn't obscure like a can of rustolium.
  18. Honestly? I had an Ishapore and wanted it to...

    Honestly? I had an Ishapore and wanted it to look CDN but because of issues, it still looked Ishy. You can't make it do what it won't. Even if one tries to change a barrel to make it an inch...
  19. Replies
    8
    Views
    372

    You should be able to do that Patrick, just look...

    You should be able to do that Patrick, just look at the page when you want to edit and it gives you the option of delete.
  20. The barrel is a metric...unless it's made in USA....

    The barrel is a metric...unless it's made in USA. I think it's a Belgian part so it's metric. Here's a thread about this to read... So if it's backwards then the other won't fit anyway. Remove...
  21. Replies
    13
    Views
    409

    Here's a live link... M1917 Rifle from Forge...

    Here's a live link...

    M1917 Rifle from Forge to Finish - YouTube
  22. I was hooped for recourse as there's no one...

    I was hooped for recourse as there's no one locally that could have sorted it. It would need bead blasted and redone. I assembled it and shot it a bit until the left top edge of the bolt track...
  23. Replies
    15
    Views
    460

    Just start a thread and ask us directly. The...

    Just start a thread and ask us directly. The search feature here will also glean much hidden info that's already been published...
  24. The FAL should be a metric thread first off...and...

    The FAL should be a metric thread first off...and the slotted flash hider an Imperial. That is if it's UK made, if it's an Indian it's different. The Indian guns were a mix of Metric, Imperial and...
  25. Agreed. People ask how safe to shoot these are...

    Agreed. People ask how safe to shoot these are if made by locals, I suspect this one has had it's share of combat action in past.
Results 1 to 25 of 117
Page 1 of 5 1 2 3 4
Warpath Vintage