Search:

Type: Posts; User: Patrick Chadwick; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 5 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    7
    Views
    329

    Yes, it's Iraqi. 1955 if the 2nd figure is indeed...

    Yes, it's Iraqi. 1955 if the 2nd figure is indeed a 9 (not clear in photo).
  2. Replies
    5
    Views
    180

    Well, being a little bit puzzled by your problem,...

    Well, being a little bit puzzled by your problem, I just checked with "Ivan The Terrible" - my Been There and (quite possibly) Done That 1943 Mosin-Nagant sniper. The eye relief - measured from the...
  3. Replies
    5
    Views
    180

    Doesn't sound right to me. The PU scope protrudes...

    Doesn't sound right to me. The PU scope protrudes backwards quite a way, and if you have to crane your head forwards, then you are an unwitting candidate for the "scoper's badge" of a bloody crescent...
  4. Replies
    7
    Views
    329

    What you really discovered was that there are...

    What you really discovered was that there are some very careless shooters around !
  5. Replies
    5
    Views
    209

    According to Stratton/Vol.2 P. 102 , the...

    According to Stratton/Vol.2 P. 102 , the "fore-end reinforcing screw" was 1.65" long, which is a bit longer than 1-5/8" - please check your measurement - but even 1-5/8" ought to allow the slotted...
  6. Replies
    2
    Views
    110

    The front sight blade appears to have been...

    The front sight blade appears to have been unchanged from its introduction on the M1871 rifle. When I needed a higher blade for my 1871, I simply put in a K98k replacement blade.

    Your link doesn't...
  7. Replies
    36
    Views
    4,569

    Excellent Ovidio! Now here's a useful dodge for...

    Excellent Ovidio! Now here's a useful dodge for people (like me) who don't like filing around on original rifles.

    The M1917 backsight is limited by the crude "notch" steps... go one step higher,...
  8. Replies
    13
    Views
    472

    I apologize for this not being a straight answer...

    I apologize for this not being a straight answer to your question, but I do not think that trying to zero a rifle with open sights at 25 yards is a very good idea, UNLESS you use a target that is...
  9. Well, don't try this out on a valuable part, but...

    Well, don't try this out on a valuable part, but I once achieved a parkerization "look-alike" finish by accident.

    I had wanted to remove the rust on a couple of screw dies, and dunked them in a...
  10. In other words: Buy Now While Stocks Last !!!

    In other words: Buy Now While Stocks Last !!!
  11. For which there is a separate "Appraisals" forum.

    For which there is a separate "Appraisals" forum.
  12. Of course, as a one-time military rifle with a...

    Of course, as a one-time military rifle with a full-length stock, it is clear that the stock has been cut down. Look up a few photos in the internet to gauge the proportions, and you can judge that...
  13. Lovely rifle, wrong forum!

    Lovely rifle, wrong forum!
  14. Replies
    10
    Views
    708

    Wow Alan, but that is a beeyootifull set!

    Wow Alan, but that is a beeyootifull set!
  15. Replies
    1
    Views
    243

    The problem of sizing for a Hall rifle is really...

    The problem of sizing for a Hall rifle is really just the same as for a percussion revolver. The ball must be held firmly in the chamber, but not overstress the barrel.

    My very serious...
  16. Value? Enough

    Now that this seemingly endless thread appears to be fading out, may I ever so gently point out that there is a forum:

    Appraisals, Fakery, Dispute Resolution & Mediation Forum

    which exists for...
  17. Basic measurement caution

    This is an oldie:

    The fact that an instrument has a resolution of 0.001" does NOT mean that it is accurate to 0.001".

    The slightest bit of grease or dust on the faces of a gauge will affect...
  18. Replies
    23
    Views
    832

    A great piece of work, but I'm not familiar with...

    A great piece of work, but I'm not familiar with the term "card stock". Please could you explain?
  19. Replies
    10
    Views
    3,792

    Eaglelord17: If that was at 100yds, then it is a...

    Eaglelord17: If that was at 100yds, then it is a very good group for a military rifle with open sights!
  20. "Isn't that how it's done?" Er, sorry Jim, but...

    "Isn't that how it's done?"

    Er, sorry Jim, but not according to P.107 of Wirnsberger "Standard Directory of Proof marks".

    The "Not English Make" was to be marked on foreign-made barrels...
  21. Winchester 94 from a French contract. OK,...

    Winchester 94 from a French contract. OK, understood that.
    But what I don't follow is

    "the second set of proofs would be from the "Guns For Britain" emergency after Dunkirk and being taken into...
  22. Replies
    37
    Views
    1,355

    - sorry, was interrupted

    It seems that your bore is seriously worn. I have not yet found any official definition of maximum land and groove diameters. Until they turn up, let's look at it from a practical viewpoint.
    ...
  23. Replies
    37
    Views
    1,355

    "Correct" is not a word that you will find in...

    "Correct" is not a word that you will find in standards documentation, but a somewhat subjective adjective, popular with collectors, that already implies a judgement.

    The "Masstefeln für...
  24. " I know its French polish beneath the cosmoline,...

    " I know its French polish beneath the cosmoline, so i can't use alcohol based cleaners because it will wreck the original finish."

    French polish + Cosmoline = NOT original finish.

    So-called...
  25. Replies
    9
    Views
    428

    Normally, on an M1917, the muzzle-end face of the...

    Normally, on an M1917, the muzzle-end face of the front end of the stock has a letter stamp E or R or W.

    I think you would find this book useful:

    "United States Model of 1917" by C.S. Ferris....
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4