ok, thank you for answering
so on all m1903 they used only walnut wood?
sorry, what do you mean that there is wood in pù?
On the wrist I noticed that the groove is not quite thick.
in Italy...
Type: Posts; User: Wanaxit; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)
ok, thank you for answering
so on all m1903 they used only walnut wood?
sorry, what do you mean that there is wood in pù?
On the wrist I noticed that the groove is not quite thick.
in Italy...
I do not know why the images are not seen,
however inside the guard there is only one L marked and nothing else, I looked at a book but did not say anything about the other producers either
thanks...
I try to put them back
I saw that they take a while to load
if you can not see the pictures let me know
thanks
Gmail
Gmail
do not you see the photos?
Hello
I wanted to ask what kind of wood they used?
Can it be a replacement stock or is it something commercial?
they usually used walnut that was darker.
It has no marks on the stock, it is kept...
it is of the first type, there is a proof that confirms it is from the winchester
thank you
the trigger group on which it is mounted is of the Winchester in excellent condition, I have not found anything on books or on the internet
thank you
I apologize if you do not see the image, inside the trigger guard there is the symbol of an L (first picture)
...
Hello
you have any idea who produced this trigger guard, inside it says L
it's on trigger group W.R.A. Garand M1
thanks
thank you so much
the recharge that I have tried so far is 44.8 grains of powder imr4895 with 150-155 grains ball.
seeing the primer does not seem to me there are overpressure, but it happened to...
sorry English I know very little and then use google translator, then reread what I wrote you do not understand anything I apologize.
can the bent weapon rod cause a loss of precision?
what doses...
Hello
can the crooked performance rod negatively affect Garand's accuracy?
Another thing how do you recharge the cartridges?
It happened to me that about the second - third shot the cartridge...
thank you so much for the explanation
another thing, the gas cylinders were burnished even if they were made of stainless steel or not?
PS: the images I uploaded are seen? thank you so much
sorry if you can not see the images I try to post them again
thank you
Gmail
Gmail
Hello
the weapon in question is HR and there are punches that I did not understand what they mean, two are placed on the bolt and are A16 and BJE and the other on the receiver, that "AR" immediately...
thanks a lot to everyone.
One question: is it true that you can use a .357 magnum cartridge case as a casing for the .351 wsl?
thank you very much RCS
Hello
I would like to know something more about this m1907 and what do you think about it, I found little on the internet and I would like to know if this was supplied to the police and a little bit...
Hello
I'm a stupid in the end I managed to solve the problem, the lever of the lever to remove the magazine came slightly out and did not allow me to raise the trigger guard altogether
thank you...
hello and thanks for replying
I took the image on the internet and it is not my weapon, it was an example of what I can not do, that is to raise the guard of the trigger, it reaches up to a point...
https://www.milsurps.com/images/imported/2018/08/p1070440-1.jpg
hello I hope you can see the image taken on the internet but shows the operation that I can not do because the trigger guard in...
thank you for answering
the problem is that I can not remove the part of the receiver / barrel from the kick because the trigger group trigger guard does not get up, it's like something is...
hello I'm new and or a problem in the dismantling of the m14, when I do to raise the trigger guard gets up to half then crashes and is hard and the weapon can not be disassembled. can you tell me how...
hello I like weapons and their history of ww1 ww2