Search:

Type: Posts; User: tiriaq; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 5 1 2 3 4

Search: Search took 0.04 seconds.

  1. This is the carbine with a knurled tubular...

    This is the carbine with a knurled tubular cocking piece wrapped around the receiver?
  2. Replies
    7
    Views
    312

    Value? Given the OP's description of the bore, I don't...

    Given the OP's description of the bore, I don't think it could be called "shooter grade".
  3. Replies
    6
    Views
    322

    Mclean house, Appomattox.

    Mclean house, Appomattox.
  4. Looks to be a training rifle.

    Looks to be a training rifle.
  5. Replies
    34
    Views
    2,033

    These were at Accuracy Plus in Peterborough. ...

    These were at Accuracy Plus in Peterborough. They could very well have been part of that batch.
  6. Replies
    34
    Views
    2,033

    It is unusual to see a rifle with the substitute...

    It is unusual to see a rifle with the substitute parts still installed. These were pretty thoroughly culled out and replaced.
    Not too many years ago I saw a batch in Ontario that had retained all...
  7. Replies
    18
    Views
    1,244

    That would make so much sense. The cadet program...

    That would make so much sense. The cadet program could certainly use the support.
  8. Replies
    18
    Views
    1,244

    And CNo7 rifles are being deactivated for use by...

    And CNo7 rifles are being deactivated for use by Cadets as drill rifles.
  9. Replies
    11
    Views
    637

    If you have a pristine No. 1 Mk. III, please...

    If you have a pristine No. 1 Mk. III, please don't butcher it to make a Delisle reproduction. There are lots of already sported SMLEs out there. All you need is from the receiver ring back. ...
  10. Replies
    2
    Views
    137

    A variety of cocking handles were made. I...

    A variety of cocking handles were made. I suppose that the Mk. II would have been the most common prior to the introduction of the Mk. V, and the widespread conversion of carbines to use it. Main...
  11. Replies
    6
    Views
    428

    A post front sight and a round aiming mark can...

    A post front sight and a round aiming mark can also contribute to vertical stringing.
  12. I might have a cutoff. Will check tomorrow.

    I might have a cutoff. Will check tomorrow.
  13. The rear sight base should be visible on the top...

    The rear sight base should be visible on the top of the barrel just in front of the receiver.
    I suppose that Remington could have made replacement 03 barrels.
    I suspect, though, that the barrel...
  14. Is the existing barrel an 03 or 03A3? If it is...

    Is the existing barrel an 03 or 03A3? If it is an 03A3, there is no provision for the rear sight, so configuring the rifle as an 03 would be problematic.
  15. Replies
    24
    Views
    5,446

    Here in Canada, perhaps the wisest way to have a...

    Here in Canada, perhaps the wisest way to have a simulated suppressor is to have the barrel pass through, end to end.
    A non-restricted barrel must exceed 18 1/2". A semi auto Sten with a barrel...
  16. The holes at the muzzle would be for a front...

    The holes at the muzzle would be for a front sight, not a scope block.
  17. Replies
    24
    Views
    1,216

    Value? Set up for shooting the US National Match course...

    Set up for shooting the US National Match course of fire. Discipline shot at both the state and national level. The Nationals are held at Camp Perry, Ohio every summer.
    Course of fire includes...
  18. Original stocks were cut using a series of single...

    Original stocks were cut using a series of single purpose, very heavy duty machines.
    Modern stocks will likely be made using either a manual pantograph carving machine or a CNC machining center. ...
  19. Replies
    14
    Views
    657

    Exact same process as raising a dent in a shotgun...

    Exact same process as raising a dent in a shotgun barrel.
  20. The rifle is fitted with a Central mounting plate...

    The rifle is fitted with a Central mounting plate and target rear sight. The Central sight could be used on a variety of rifles, by installing the appropriate mounting plate.
    These are vintage...
  21. Replies
    3
    Views
    292

    Should you ever be near Trenton, Ontario, go to...

    Should you ever be near Trenton, Ontario, go to the Air Force Museum at CFB Trenton. They have a Halifax bomber which was shot down over Norway in the spring of 1945, just before the end of the war,...
  22. Thread: 68 Gram

    by tiriaq
    Replies
    5
    Views
    467

    1:7 is a faster twist than needed for most any...

    1:7 is a faster twist than needed for most any .224 bullets used in an AR. It was adopted in order to stabilize the very long tracer bullet.
  23. Thread: 68 Gram

    by tiriaq
    Replies
    5
    Views
    467

    You can shoot a 68gr bullet in a 1:7 .223.

    You can shoot a 68gr bullet in a 1:7 .223.
  24. Replies
    3
    Views
    322

    The photo is of the receiver, a Mk. II which was...

    The photo is of the receiver, a Mk. II which was drilled and tapped for a rear bridge.
    Probably safe to assume that the barrel is one for a Mk. II rifle.
    Remove the lock screw and it should be...
  25. Thread: Mills Bomb

    by tiriaq
    Replies
    20
    Views
    1,069

    Many years ago, I was visiting a chap. On the...

    Many years ago, I was visiting a chap. On the mantelpiece in his den were some militaria. One item was a 36M. Had a quick look at it, and asked him if he knew it was live. He did, but it was OK...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4
Gunonline.com