+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 22

Thread: № 32 / № 42 - Scope Graticule Replacement

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Scout Sniper's Avatar
    Join Date
    Jul 2019
    Last On
    12-11-2023 @ 05:45 PM
    Location
    United Kingdom
    Posts
    232
    Local Date
    03-28-2024
    Local Time
    05:33 PM

    № 32 / № 42 - Scope Graticule Replacement

    Hello Milsurps,

    Im looking to replace a № 42 graticle, i said № 32 as they are very similar.

    My question is does anybody have any advice on replacing Graticules. Pictures of the piece that holds the graticle itself would be handy.

    I have already seen the info on here giving wire dimensions etc...

    I also have Peter Laidlericon's book on the № 32.

    But i would still like to see the graticle piece inside.

    My № 42 is perfect condition and the optics are crystal clear but i would like to change the graticle to the rail and post like the № 32. It looks like the threads have been sealed, maybe thats why its still so clear.
    The № 42 did have a variation with the rail and post that was mounted on the .22 Winchester Model-74.

    Mine is 1943 dated R.E.L/Canadaicon Mk1

    Attachment 102189Attachment 102188Attachment 102190Attachment 102191
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Scout Sniper's Avatar
    Join Date
    Jul 2019
    Last On
    12-11-2023 @ 05:45 PM
    Location
    United Kingdom
    Posts
    232
    Local Date
    03-28-2024
    Local Time
    05:33 PM
    Thread Starter

    Cool

    I decided to have a go at disassembly, i have tried to unscrew the brass front shade a few times before but it wont budge a mm.

    The screw on the front shade came undone like it was dont up a couple of days ago.

    I could see the threads had been sealed with like a grey putty. It was soft and could be scraped away easily with a wooden tooth pick but the thread was still solid.
    I decided to heat the front shade gently with a hairdryer, still it wouldnt come undone as i couldnt grip it good enough. I wrapped masking tape around the brass shade to aid grip, put on my leather palmed cycling gloves and kept the scope in the mount to hold the tube. Heated it again and the grip was so good i could unscrew it easily. Success!

    Next was removing the lenses, under a hidden pocket of more putty i could see a tiny screw head. I cleaned it out and it once again un screwed like it had just been done up!
    I had to apply a small bit of heat after that and the lense slid right out.

    At this point i could now see the graticule inside, once again i located another hidden tiny screw covered with putty. A quick dig with a wooden tooth pick and its accessible. Again undid very easy, and that was it. The graticule tube slid out like a treat.

    Well its absolutely nothing like the № 32 diaphragm wise, obviously this scope has no adjustment so its a fixed tube with wires soldered in place.

    All i have to do is fit a new graticule, easier said than done!

    I studied it hard to figure out how they mounted it square and the wires perpendicular to each other.
    Very clever, they have machined a very small Vee slot so the wire drops into the Vee essentially self locating on the centre line. Then soldered in place.

    To achieve what i would like, i need to get another vee slot machined perfectly square to the verticle slot. Fit wires, job done! Cough!! 🤣

    Would anybody like to help with machining these for me, any help much appreciated.
    All i need is the machining work done and im happy to do the wires...

    Attachment 102217Attachment 102216Attachment 102218

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member Scout Sniper's Avatar
    Join Date
    Jul 2019
    Last On
    12-11-2023 @ 05:45 PM
    Location
    United Kingdom
    Posts
    232
    Local Date
    03-28-2024
    Local Time
    05:33 PM
    Thread Starter
    Anybody have any wire or know where to find sum?

    Thanks

  6. #4
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-28-2024
    Local Time
    07:33 PM
    Save yourself a whole lot of bother and get a No 42 or 53 with what looks like a horizontal AND vertical crosswire. These are actually etched onto a glass plate (which changes the nomenclature from a graticle to a reticle). You then have an already (reasonably) accurately collimated centre-dot/spot to aim with instead of the vertical line which was OK when using it to aim the BESA gun on the Mk7 Churchill but, alas, not a good way to hit targets with a rifle.

    The BAD thing about trying to convert your existing No42 inner sleeve (the long brass bit that holds the wire) is that to fix a NEW wire and post, you have to heat up the whole thing to the melting point of solder before it will take. If you insist on converting the glass reticle to cross-wire and post, you can kick out the plate and fit the new wire and post. And you only have a simple 1/16" thick plate to heat up

    PS, the reticle plate is held in with screws. Easy to undo, work on and replace.

  7. Thank You to Peter Laidler For This Useful Post:


  8. #5
    Legacy Member Scout Sniper's Avatar
    Join Date
    Jul 2019
    Last On
    12-11-2023 @ 05:45 PM
    Location
    United Kingdom
    Posts
    232
    Local Date
    03-28-2024
    Local Time
    05:33 PM
    Thread Starter
    Thanks for the info Peter.

    I should have clarified im looking to use this scope more as a prop than a scope i will be shooting with. Perfect post and wire centering is not essential for this project. I have a 1943 Long Branch and would like to be able to sit this Canadianicon 1943 scope on top of it.

    Realistically if i can get the vee machined then mounting the wire should be pretty straight forward.
    I have engineering knowledge and im handy at fine work through an eye glass.

    At work we have sum amazing loctite adhesive for metals and was going to glue rather than solder. I know, i know... glue sounds terrible but trust me the glues these days are amazing and will be almost as strong as solder.

    I have my heart set on this scope also for the amazing condition its in. Its one of the best i have seen, and 42 prices seem to be creeping up. I was lucky, this cost me £50!
    Last edited by Scout Sniper; 08-11-2019 at 11:58 AM.

  9. #6
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-28-2024
    Local Time
    07:33 PM
    I was going to say how simple it all seems to be nowadays but will hold off on that. But back to the subject and keep my immediate thoughts to myself.....

    You are really making a mountain out of a molehill if you don't mind me saying. If, as you say, a perfect post isn't an important or critical issue then centreing the little V slot for the upright grat post is absolute simplicity itself. And by using a pair of dividers, you will get the new slot EXACTLY square and EXACTLY central. Exactly right should be near enough I say.

    Hold inner sleeve in 3-jaw vice and file small accurately marked out slot with model-makers triangular needle file. Make sure that you don't touch the crosswire while doing so. Done that and filed a small slot........?
    Now mount .006" steel wire into a watchmakers lathe and grind the angled tip of the new post. 10 minutes work - and you'll need your eye glasses for this so get them handy.....
    Lay new-made post on inner sleeve. Adjust height in relation to the crosswire, dob of glue, allow to set and there it is. Simple as falling off a log as they say around these parts.

    New problem. Assemble up. If locating peg on inner sleeve (shown in photos) puts new post and crosswire 90degrees out in relation to the scope markings and segment cover, just rotate scope to suit OR rotate inner sleeve until it is correct in relation to your rifle. Drill and tap 10BA, replace anti rotation screwed peg and assemble up
    What could possibly go wrong?

  10. #7
    Legacy Member Scout Sniper's Avatar
    Join Date
    Jul 2019
    Last On
    12-11-2023 @ 05:45 PM
    Location
    United Kingdom
    Posts
    232
    Local Date
    03-28-2024
    Local Time
    05:33 PM
    Thread Starter
    Yeah, that is pretty straight forward!
    Thanks for taking the time to lay it out like that, sometimes my brain runs away with itself... i will follow all advice.

    Think my biggest issue will be sharpening the post. I have a standard lathe (Colchester Bantam) but that is a tad too big.
    Maybe i need to find a watch maker who can grind me up a post or 2.

    Thanks again Peter, i will update this tread with pictures as i go.

  11. #8
    Legacy Member Roy W's Avatar
    Join Date
    Aug 2015
    Last On
    Today @ 07:05 AM
    Location
    Hampshire
    Posts
    561
    Local Date
    03-28-2024
    Local Time
    12:33 PM
    Why not just find a real No32 scope to put on the rifle, or one of the copies, if it is just a prop?

    There can't be too many REL No.42's around, especially in that condition. Shame to damage it

  12. #9
    Legacy Member Scout Sniper's Avatar
    Join Date
    Jul 2019
    Last On
    12-11-2023 @ 05:45 PM
    Location
    United Kingdom
    Posts
    232
    Local Date
    03-28-2024
    Local Time
    05:33 PM
    Thread Starter
    I cant afford a real No.32 and i dont want to buy a reproduction.

    I take your point onboard about my scope but i wouldnt say im damaging it. Just modifying it and could be put back as was at any point. Just think of all the No.42 that have been sacrificed to save a No.32.
    At least mine is loved and will be enjoyed. Just like the date and Canadianicon connection between scope and rifle.

  13. #10
    Advisory Panel
    Roger Payne's Avatar
    Join Date
    Mar 2008
    Last On
    03-20-2024 @ 06:05 AM
    Location
    Sutton Coldfield, UK.
    Posts
    3,429
    Real Name
    Roger Payne
    Local Date
    03-28-2024
    Local Time
    05:33 PM
    Roy, you’d probably want to hang me from the nearest yardarm then........I have a large cardboard box FULL of No42 & No53 tubes that I’ve nadgered over the years in order to pinch the lenses to complete needy No32’s. Other parts come in handy too, such as the segments, ocular lens retaining rings, & even the tubes themselves. Thanks to a trick taught to me by Peter years ago, even a No32 with a rusted through or torn ocular housing can be repaired with a little ‘grafting’.

  14. Thank You to Roger Payne For This Useful Post:


+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. No 32 graticule repair - materials and methods
    By jss in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 3
    Last Post: 08-10-2017, 06:02 AM
  2. No.32 MkII with cross wires graticule not post & crosswire
    By desperatedan in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 7
    Last Post: 07-12-2015, 01:47 PM
  3. Berdan II, Бердана № 2 обр. 1870 года
    By slovakia in forum Black Powder
    Replies: 2
    Last Post: 03-08-2013, 07:14 AM
  4. Need a replacement stock
    By JimB in forum M1/M2 Carbine
    Replies: 8
    Last Post: 07-28-2009, 08:18 AM
  5. Questions about №4 MK I*
    By dimon in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 16
    Last Post: 05-17-2008, 12:01 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks