+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14

Thread: Smith 1917 Conundrum

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member jakebevt48's Avatar
    Join Date
    May 2018
    Last On
    01-29-2023 @ 07:51 AM
    Location
    Tennessee
    Posts
    41
    Local Date
    03-18-2024
    Local Time
    10:42 PM

    Smith 1917 Conundrum

    I recently acquired a Smith and Wesson 1917. It is US Property marked. It's serial number is 628xx.

    The Good:
    It came with a leather (non standard issue) holster stamped "Service in Worlds War 1918 J.F.R." It also has "J.F. Rose" stamped elsewhere on the ammo belt.

    The Bad:
    The GI gave it some "hand checkered" grips with his pocket knife. Sigh.

    The Ugly--(and some questions):
    It is theoretically a 45ACP, however 45ACP, rounds will drop all the way through the cylinder holes. Is this normal, or has this gun been reamed to 45 Colt?

    I ordered full moon clips and shot it today. However, the loaded moon clips do not go into the cylinder very smoothly. You have to push them hard to get them to seat enough to close the cylinder. Maybe an issue with the clips (from SpeedBeez)?

    Also, when I shot it today it shaved a good chunk of copper off of one round. So, I realized I have some timing problems too. This gun has turned out to be a bit of a lemon. Anyone send a 1917 back to Smith and Wesson to have the timing fixed before? Or should I send it to Clark's custom guns?

    Thanks
    Jake
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member jakebevt48's Avatar
    Join Date
    May 2018
    Last On
    01-29-2023 @ 07:51 AM
    Location
    Tennessee
    Posts
    41
    Local Date
    03-18-2024
    Local Time
    10:42 PM
    Thread Starter

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Contributing Member rcathey's Avatar
    Join Date
    Dec 2012
    Last On
    03-14-2024 @ 03:09 PM
    Location
    St. Louis, MO Area
    Posts
    1,645
    Local Date
    03-18-2024
    Local Time
    09:42 PM
    45 ACP should not go through. I would agree it’s been reamed out. 45 Colt seems like a likely candidate.
    The moon clip issue is interesting. Mine drop right in.
    Perhaps it’s had an entirely different cylinder dropped in that has a different spacing. That would explain the timing issue as well.

    And by the way, I love those grips. Trench art type modifications to firearms are cool to me.
    I’d gladly trade you the grips from my 1917 if you’re interested. Shoot me a PM if you are!

  6. #4
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:51 PM
    Location
    Victoria BC
    Posts
    29,810
    Real Name
    Jim
    Local Date
    03-18-2024
    Local Time
    07:42 PM
    Quote Originally Posted by rcathey View Post
    Perhaps it’s had an entirely different cylinder dropped in that has a different spacing.
    I agree, can you find a number stamped on the cylinder rear that should also match one on the bottom of the barrel. Get a .45 ACP cylinder and the cartridges go in and stay. The clip makes it so they eject. I doubt the clips are to blame but can't say as I haven't used them. Mine came from Brownells and were full moon. I only have one single half moon clip... We should be able to give you a measurement for a cylinder in .45 ACP and one in .45 Colt. The thin rim of the long cartridges have the cylinder sitting far back to the recoil shield...
    Last edited by browningautorifle; 05-14-2019 at 11:20 PM.
    Regards, Jim

  7. #5
    Legacy Member jakebevt48's Avatar
    Join Date
    May 2018
    Last On
    01-29-2023 @ 07:51 AM
    Location
    Tennessee
    Posts
    41
    Local Date
    03-18-2024
    Local Time
    10:42 PM
    Thread Starter
    I thought about it more, and realized I have one moon clip that drops in very easily. It is loaded with self defense ammo, whereas all the other stiff ones were loaded with some remanufactured brass case ammo. I’ll blame that remanufactured ammo for some of the problems.

    The number on the cylinder does not match the frame. But like I said it will close and shoot with 45ACP in the clips. The cylinder has a couple H looking marks on it, as well as a serial number and a eagle head or something with S24 under it.

    Also, I realized the ejector rod is slightly bent. This thing is looking worse by the second.

  8. #6
    Contributing Member rcathey's Avatar
    Join Date
    Dec 2012
    Last On
    03-14-2024 @ 03:09 PM
    Location
    St. Louis, MO Area
    Posts
    1,645
    Local Date
    03-18-2024
    Local Time
    09:42 PM
    Ejector rods can be straightened but unless you have the tools (I use a metal lathe and a dial indicator) it probably makes more sense to buy a new one. I wouldn't think it would cost any more than $20 for just the stripped rod. You'd have to add parts from yours on to it.

    The mark on the cyclinder you describe is appropriate. Sounds like a correct cylinder to me. Maybe your ejector rod is the root of the problems.

  9. #7
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:51 PM
    Location
    Victoria BC
    Posts
    29,810
    Real Name
    Jim
    Local Date
    03-18-2024
    Local Time
    07:42 PM
    Quote Originally Posted by rcathey View Post
    Maybe your ejector rod is the root of the problems.
    Agreed, it will turn the cylinder out of true...first thing a pistol smith checks is frame straightness and discards those simple parts for replacement. Your centerpin will be bent too...just a bit.
    Regards, Jim

  10. #8
    Legacy Member Bruce McAskill's Avatar
    Join Date
    Mar 2009
    Last On
    01-17-2023 @ 09:10 PM
    Posts
    1,880
    Local Date
    03-18-2024
    Local Time
    09:42 PM
    A lot of the 1917 pistols went to the US mail service. Some of them where chambered to the .45 Long Colt as that is what some of the Mail agents wanted. Ammo was available for the .45 Long Colt out west more so then .45 acp as most of the pistols were in military use so not much demand for the .45 acp at that time.

  11. #9
    Legacy Member Bruce McAskill's Avatar
    Join Date
    Mar 2009
    Last On
    01-17-2023 @ 09:10 PM
    Posts
    1,880
    Local Date
    03-18-2024
    Local Time
    09:42 PM
    S&W no longer works on the older hand ejectors. They don't even have parts for them anymore. They sold what they had to a company named Jack First if I remember right. A parts supply outfit.

  12. #10
    Legacy Member jakebevt48's Avatar
    Join Date
    May 2018
    Last On
    01-29-2023 @ 07:51 AM
    Location
    Tennessee
    Posts
    41
    Local Date
    03-18-2024
    Local Time
    10:42 PM
    Thread Starter
    I did ask Smith and Wesson a few days ago, and you are correct, they no longer work on them. Jack First Gun Supplies does not seem to have any parts available on their website.

    Honestly, I'm kind of bummed about this revolver. I'll probably sell it (and I'll be sure to let the buyer know about the issues). Thanks for your help though gentlemen!

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. Smith corona
    By cmecha in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 3
    Last Post: 03-12-2012, 09:09 AM
  2. Bubba No4 MKI sniper conundrum..ID help?
    By ickmann in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 7
    Last Post: 01-27-2012, 12:50 AM
  3. Smith & Wesson 1917 2" revolver
    By userids in forum Milsurps General Discussion Forum
    Replies: 2
    Last Post: 02-22-2010, 09:59 AM
  4. Who is R.M. Smith, III
    By Loy Hamilton in forum M1 Garand/M14/M1A Rifles
    Replies: 12
    Last Post: 11-15-2009, 11:09 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks