+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 19

Thread: 1897 Project No. 2

Click here to increase the font size Click here to reduce the font size
  1. #1
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    04:01 AM

    1897 Project No. 2

    Here we go! Still has matching serial on the extension and original 30" full choke. 739xxx, early 1924 according to https://www.winchesterguns.com/conte...ture-dates.pdf. Forend was very loose and already on it's last notch. A swap of the adjusting sleeve cured that problem.

    The last one I just finished was far worse off - bent and dented barrel, broken extension. This one's major defect is that it's just plain filthy. Filthiest firearm I've ever encountered (including the mosin's I've done - one that appeared straight out of the sewer and another still packed in cosmolineicon).

    Lot's of old dried grease/oil mixed with carbon/dirt/dust/sand forming a concrete in every corner, under every spring.


    The consistency of grime changes with likely exposure during storage. Areas around the bolt and front of the carrier are a loose mix of dust and grease, forming almost like a soft packed felt substance. In the rear and along the sides, its rock hard and gritty. Brake cleaner wouldn't touch it. After a soak in wd-40 followed by a brass scraper to chisel out the worst of it, then a brass brush to get the rest of major deposits, I have it all boiling in water to get the remainder - while I prep the receiver for rust bluing.

    Note the deep striations in the outside receiver. I saw these in the last 97 project, although they hadn't worn as deep as this one. From my experience there, these are caused by the metallurgy of the receiver. They present a challenge in bluing to get rid of them. I'll capture this in my next post.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    01:01 AM
    Quote Originally Posted by ssgross View Post
    Note the deep striations in the outside receiver. From my experience there, these are caused by the metallurgy of the receiver.
    That's what we thought too, from looking at '94 Winchesters, rifles and carbines from early 1900s.
    Regards, Jim

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    04:01 AM
    Thread Starter
    This one needs/demands new wood. Boyds sells original pattern forends. Their butts are available in XX walnut, but their pics are horrible so no telling what I'd get. The wrist looks a little stubby. However midwayusa has a pick of a Boyd butt that looks perfect, but they out of stock. I'm thinking I want something mid-grade, not over the top but with a just bit of curl. When I'm done practicing on scraps, I think I'll make my checkering debut on this one. Has anyone used one of the Boyds stocks? are they indeed as ugly and misshapen as their single photo lets on? or is the wrist longer like in their version sold on midwayusa?

    the Boyds stock on Boyds website...
    the midwayusa Boyds stock...

  6. #4
    Legacy Member Tom Doniphon's Avatar
    Join Date
    Mar 2009
    Last On
    @
    Posts
    317
    Local Date
    03-28-2024
    Local Time
    01:01 AM
    739xxx would have had its serial number applied in October 1920.

  7. #5
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    04:01 AM
    Thread Starter
    Quote Originally Posted by Tom Doniphon View Post
    739xxx would have had its serial number applied in October 1920.
    Thanks, Tom. Can you provide your source as that is different then what I found, linked above?

  8. #6
    Legacy Member Tom Doniphon's Avatar
    Join Date
    Mar 2009
    Last On
    @
    Posts
    317
    Local Date
    03-28-2024
    Local Time
    01:01 AM
    Winchester Polishing Room Serialization Records. They show when the serial number was applied to the receiver. They are the most accurate way to date a Winchester. Most all of the other serialization tables are incorrect or have some errors in them.

  9. Thank You to Tom Doniphon For This Useful Post:


  10. #7
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    04:01 AM
    Thread Starter
    long overdue. got busy.

    So the topic I promised was rust bluing with these "flaws" in the metal that was producing the striations which wear faster than the surrounding metal, and then look like long deep scratches after 100yrs. After lots of trial and error with the last 97, this one went along pretty uneventful.


    as soon as you degrease, these lines flash rust, deep and fast. Don't worry. just don't let it sit - go ahead and wipe on your first iteration.


    I'm using mark lee's express blue no. 1. you can see the striations aren't playing nice. Just ignore them and keep going


    it gets worse in the boil. now, when it comes out and after carding, grab a square of clean paper, and lightly go over the area until the lines disappear. In my initial prep, I usually finish with a piece of worn paper, so I go one step of finer grit this time so there is nothing that stands out. The etching of the rust process will make any variation irrelevant and unnoticeable in the end, so long as you finished at ~320grit or beyond (depending on manufacturer of the paper. no benefit to going finer than needed. 400 seems to be a good number that works across many brands, even the cheap stuff.) You can't see it, but there is just barely enough magnatite over the striated spot to keep it from flash rusting again, so at the next application the striations catch up.


    here we are after the second application, just before boiling.

    now where did I save the final pics, with the bolt and everything? ugh.
    Last edited by ssgross; 01-10-2023 at 08:54 AM.

  11. The Following 4 Members Say Thank You to ssgross For This Useful Post:


  12. #8
    Contributing Member fjruple's Avatar
    Join Date
    Dec 2006
    Last On
    10-29-2023 @ 04:38 AM
    Location
    New Jersey, USA
    Posts
    1,021
    Real Name
    Franklin Ruple
    Local Date
    03-28-2024
    Local Time
    04:01 AM
    Good luck on your project, please keep us advised of your progress!!

  13. #9
    Legacy Member RAM1ALASKA's Avatar
    Join Date
    Aug 2020
    Last On
    Yesterday @ 10:47 AM
    Location
    Southcentral AK
    Posts
    68
    Real Name
    Rob
    Local Date
    03-28-2024
    Local Time
    12:01 AM
    Always a pleasure watching the many steps it takes to bring these projects to life!

    Thank You

  14. Thank You to RAM1ALASKA For This Useful Post:


  15. #10
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    04:01 AM
    Thread Starter
    here it is.

    There was some prior moderate corrosion top front that made the oval-pw stamp pretty faint when it was all done, even though I tried to be as delicate as possible to that area. It's still there, and stands out if you hit the light at just the right angle.
    The barrels (original 30" full choke + NOS norinco 20" riot) still need blued, along with mag tubes, slides, and extensions. I think instead of bluing this weekend I'll be drinking away my sorrows over the wood I got in the mail today (see other thread in this forum).

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. 1897 Project No. 1
    By ssgross in forum Military Shotguns
    Replies: 47
    Last Post: 06-25-2023, 06:30 PM
  2. 1897 Winchester What?
    By Rubicon2003 in forum Military Shotguns
    Replies: 2
    Last Post: 08-22-2018, 11:50 AM
  3. Win. 1897 Riot ???
    By gunsdora in forum Military Shotguns
    Replies: 2
    Last Post: 11-27-2015, 09:30 PM
  4. 1897 Take Down Model
    By cm1 in forum Military Shotguns
    Replies: 0
    Last Post: 02-16-2010, 07:23 PM
  5. Win. 1897 Riot ?
    By jls77 in forum Military Shotguns
    Replies: 1
    Last Post: 02-12-2010, 09:19 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks