+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 23

Thread: MPI of Lee enfield No.4 MkII UF55 series

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member ToineS's Avatar
    Join Date
    Mar 2020
    Last On
    08-06-2023 @ 08:02 AM
    Location
    Netherlands
    Posts
    16
    Local Date
    03-28-2024
    Local Time
    01:02 PM

    MPI of Lee enfield No.4 MkII UF55 series

    As a long time admirer of the No.4 Lee Enfield, I managed to pick up a No.4 MkII from the UF 55 A batch.
    It was sold from an old stock and put on the market in 1995.
    They say it is from a batch made for the RAF, but I’ve never found anything to substantiate that.

    Anyway, it turns out my cousin has a similar rifle, with a serial number only a few hundred from mine.
    The thing with these two is that the MPI is more than 9” too low!
    When shooting at 100 yards, sight set at 200 yards, the MPI should be about 3” above point of aim.
    In reality, the MPI is about 6” BELOW POA...
    Not just for mine, for my cousin’s Lee as well.
    To shoot anywhere near the target we have to set the MkI sight to 450 yards!

    Are we the only ones experiencing this, or is this somehow a common feature with these rifles?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    04:02 AM
    What recipe of ammunition are you using? Anything other than the issue of the day will show deviation.
    Regards, Jim

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member ToineS's Avatar
    Join Date
    Mar 2020
    Last On
    08-06-2023 @ 08:02 AM
    Location
    Netherlands
    Posts
    16
    Local Date
    03-28-2024
    Local Time
    01:02 PM
    Thread Starter
    Quote Originally Posted by browningautorifleicon View Post
    What recipe of ammunition are you using? Anything other than the issue of the day will show deviation.
    I’m using Privi 174gr FMJ ammo. According to tests I’ve read, these fly quite true to the MkVII, which also is 174gr FMJ.

    But would different ammo produce a 9” deviation from the standard at 100 yards?

  6. #4
    Legacy Member Alan de Enfield's Avatar
    Join Date
    Nov 2007
    Last On
    Today @ 05:50 AM
    Location
    Y Felinheli, Gogledd Cymru
    Posts
    2,526
    Real Name
    Alan De Enfield
    Local Date
    03-28-2024
    Local Time
    11:02 AM
    Prvi is not exactly the same as MkVII so POI will difer.

    Simply replace the front sight blade with a smaller one. as per the table :
    Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...

  7. #5
    Legacy Member ToineS's Avatar
    Join Date
    Mar 2020
    Last On
    08-06-2023 @ 08:02 AM
    Location
    Netherlands
    Posts
    16
    Local Date
    03-28-2024
    Local Time
    01:02 PM
    Thread Starter
    Quote Originally Posted by Alan de Enfield View Post
    Prvi is not exactly the same as MkVII so POI will difer.

    Simply replace the front sight blade with a smaller one. as per the table :
    Thanks for that!
    Yes, it will not be exactly the same, but a 9” difference at 100 yards seems excessive?

    According to the calculations, I would need a -0.060 sight blade!
    I don’t think these are available, are they?

  8. #6
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 06:54 AM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,392
    Real Name
    Daan Kemp
    Local Date
    03-28-2024
    Local Time
    01:02 PM
    Interesting. Does using the battle sight result in the same MPI?

    Options: Try another ammunition brand. Fit a lower front sight. Check back sight for correct fitting.

  9. #7
    Legacy Member Alan de Enfield's Avatar
    Join Date
    Nov 2007
    Last On
    Today @ 05:50 AM
    Location
    Y Felinheli, Gogledd Cymru
    Posts
    2,526
    Real Name
    Alan De Enfield
    Local Date
    03-28-2024
    Local Time
    11:02 AM
    Quote Originally Posted by ToineS View Post
    Thanks for that!
    Yes, it will not be exactly the same, but a 9” difference at 100 yards seems excessive?

    According to the calculations, I would need a -0.060 sight blade!
    I don’t think these are available, are they?

    No a -0.060 were not available.

    The poor quality manufacture of Fazakerley rifles meant that in some batches the sighting in / zeroing was almost impossible and they applied for a derogation to allow Sten sights to be used (in that case the POI was 'high'), a short extract from a very long 'training lecture' on No4 Front sights, given by Peter Laidlericon (some years ago)

    But back to No4 rifles and the BLOCK band, foresight. Are you in for the long haul? Soon after the large late 40’s FTR programmes, it was established at Fazakerley that a large percentage of fully refurbished rifles were impossible to zero due to them shooting too high. Fazakerley sought to obtain a relaxation in order to use the +.090” and +.105” STEN gun foresight blades but already there were problems relating to the final inspection standards that I won’t go into. But the same problems were apparent outside the factories and Base Workshops, in service too so while the factories, FTR programme contractors and the large REME Base workshops were NOT permitted to use the higher Sten foresight blades, a relaxation was sought that they could be used at unit level (both high sizes) and Field workshop level (just the .090 size). But this was palliative and not a cure by any means. The answer was that where a rifle was perfect in every other way, then a Mk2 BLOCK Band foresight was available.

    Have a look at your 'Block Band Foresight' and see if it is a Mk2. (A Mk2 will be marked 1H or 2H) If it is that gives an increase in POI of two (2) front sight blades, if it is a Mk2 and you replace it with a Mk1 that effectively reduces your POI by two (2) sight blades so you can easily achieve the required 9" drop using the available sight blades.
    Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...

  10. #8
    Contributing Member CINDERS's Avatar
    Join Date
    Nov 2009
    Last On
    03-25-2024 @ 11:01 AM
    Location
    South West Western Australia
    Posts
    7,734
    Real Name
    CINDERS
    Local Date
    03-28-2024
    Local Time
    07:02 PM

  11. #9
    Legacy Member ToineS's Avatar
    Join Date
    Mar 2020
    Last On
    08-06-2023 @ 08:02 AM
    Location
    Netherlands
    Posts
    16
    Local Date
    03-28-2024
    Local Time
    01:02 PM
    Thread Starter
    Quote Originally Posted by CINDERS View Post
    Thanks! I need a -0.060 blade though…!

    ---------- Post added at 02:46 PM ---------- Previous post was at 02:45 PM ----------

    Quote Originally Posted by Daan Kemp View Post
    Interesting. Does using the battle sight result in the same MPI?

    Options: Try another ammunition brand. Fit a lower front sight. Check back sight for correct fitting.
    Yes, I will try a different ammo brand. Maybe that’s what’s causing it…
    Thanks for the suggestion!

    ---------- Post added at 02:51 PM ---------- Previous post was at 02:46 PM ----------

    Quote Originally Posted by Alan de Enfield View Post
    No a -0.060 were not available.

    The poor quality manufacture of Fazakerley rifles meant that in some batches the sighting in / zeroing was almost impossible and they applied for a derogation to allow Sten sights to be used (in that case the POI was 'high'), a short extract from a very long 'training lecture' on No4 Front sights, given by Peter Laidlericon (some years ago)

    But back to No4 rifles and the BLOCK band, foresight. Are you in for the long haul? Soon after the large late 40’s FTR programmes, it was established at Fazakerley that a large percentage of fully refurbished rifles were impossible to zero due to them shooting too high. Fazakerley sought to obtain a relaxation in order to use the +.090” and +.105” STEN gun foresight blades but already there were problems relating to the final inspection standards that I won’t go into. But the same problems were apparent outside the factories and Base Workshops, in service too so while the factories, FTR programme contractors and the large REME Base workshops were NOT permitted to use the higher Sten foresight blades, a relaxation was sought that they could be used at unit level (both high sizes) and Field workshop level (just the .090 size). But this was palliative and not a cure by any means. The answer was that where a rifle was perfect in every other way, then a Mk2 BLOCK Band foresight was available.

    Have a look at your 'Block Band Foresight' and see if it is a Mk2. (A Mk2 will be marked 1H or 2H) If it is that gives an increase in POI of two (2) front sight blades, if it is a Mk2 and you replace it with a Mk1 that effectively reduces your POI by two (2) sight blades so you can easily achieve the required 9" drop using the available sight blades.
    Thanks for that insight. Interesting stuff!
    You’d think a FTR would be ‘thorough’ right!?

    But my Lee is a new 1955 No.4 MkII which, by all accounts, should be of superior quality. Some of the best ever made, even…
    I’ll see what happens when I use different ammo, like Daan suggested.

    But if all else fails, there is a -0.060 No.1 MkIII sight blade.
    Will that fit a No.4? Opinions seem to differ, so if anyone has experience with those…? 😇

  12. #10
    Legacy Member Alan de Enfield's Avatar
    Join Date
    Nov 2007
    Last On
    Today @ 05:50 AM
    Location
    Y Felinheli, Gogledd Cymru
    Posts
    2,526
    Real Name
    Alan De Enfield
    Local Date
    03-28-2024
    Local Time
    11:02 AM
    Quote Originally Posted by ToineS View Post
    But my Lee is a new 1955 No.4 MkII which, by all accounts, should be of superior quality. Some of the best ever made, even…
    You have been reading things on the internet ..........................

    The quality produced, not only wartime, but post war was probably the worst of all manufacturers, the working relationship was appalling with unionisation and refusal to meet 'conditions' causing huge problems, and because of this they did not get future work and were closed down.

    Another small extract from one of Peter Laidlers training lessons :

    After the end of the upgrading programme, the ‘new-build’ PF- and UF55A- No4 Mk2 rifles were produced. But by this time, industrial relations at Fazakerley were best described as ‘tense’ and the factory began its slow inevitable decline. Even the offer of the secretive L2A3 Sterling and L1A1 rifle contract couldn’t sweeten or un-blinker the suicidal workforce. So while Sterling got on with making and selling its guns to the rest of the world and BSA stepped in at the last moment to rescue the L1A1 SLR, the remaining SLR machinery went from Fazakerley to Lithgowicon …………….. but that’s another story.


    Why do you think almost all of the No4T's were made using BSA manufactured rifles ?
    (The quality was better and more consistent)
    Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...

  13. Thank You to Alan de Enfield For This Useful Post:


+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. Fazakerley UF55
    By gerard488 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 15
    Last Post: 05-16-2017, 08:14 PM
  2. Enfield No4 MkII
    By capt14k in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 3
    Last Post: 03-09-2017, 02:14 PM
  3. No4 mk2 UF55 accurised by Parker Hale
    By ssj in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 15
    Last Post: 09-02-2013, 06:42 PM
  4. No 4 MKII UF55 Should I buy it?
    By fireman in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 19
    Last Post: 12-01-2010, 03:37 PM
  5. UF55 Range Rifle
    By krinko in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 14
    Last Post: 06-10-2010, 10:42 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks