+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: Salvaging & Reloading 30-06 Blanks

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member CarlC's Avatar
    Join Date
    Mar 2009
    Last On
    05-01-2022 @ 01:49 PM
    Location
    Colorado front range
    Posts
    17
    Real Name
    Carl
    Local Date
    03-28-2024
    Local Time
    04:43 PM

    Question Salvaging & Reloading 30-06 Blanks

    I inherited several thousand rounds of cardboard wad roll crimped blanks with duties as our AL Post armorer. I have pulled the powder and popped the primers (via 03) on a couple hundred to sell as brass salvage but that is time consuming and boring. With the dearth of brass and primers these days I wondered about reloading the primed brass. I opened the crimp with a tapered punch then ran them through a die sans depriming pin. What you see is what I got. The brass is mixed headstamps of 53 & 54 vintage with no indication of neck/shoulder annealing. I assume the primers are corrosive so the cases would be reloaded with cast bullets for bolt guns.

    Anybody have experience doing this? If nobody has any "OMG, never do that!" experiences or knowledge, I'll brew up a few rounds and see if the neck holds together.

    Thanks for your input,

    Carl
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Bruce McAskill's Avatar
    Join Date
    Mar 2009
    Last On
    01-17-2023 @ 09:10 PM
    Posts
    1,880
    Local Date
    03-28-2024
    Local Time
    05:43 PM
    Carl, Most of the time blanks are made from cases rejected during the loading process for normal ammunition and were not considered safe to use. Being that they were not subject to much if any pressure as blanks they were used for that. When rejected brass was not available the plants used fired brass to make blanks from but there is no way to tell what case is a flawed case and what case isn't. Might be best to just scrap the cases.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member CarlC's Avatar
    Join Date
    Mar 2009
    Last On
    05-01-2022 @ 01:49 PM
    Location
    Colorado front range
    Posts
    17
    Real Name
    Carl
    Local Date
    03-28-2024
    Local Time
    04:43 PM
    Thread Starter
    Thanks for the info. I'll pop the primers and wait for brass prices to recover. There could be a couple of needed op rods in it for us.

  6. #4
    Legacy Member sigman2's Avatar
    Join Date
    Mar 2009
    Last On
    08-14-2021 @ 10:53 PM
    Location
    North Alabama
    Age
    72
    Posts
    26
    Local Date
    03-28-2024
    Local Time
    05:43 PM
    Carl,

    I have reformed many 1909 Blanks into 6.5x55 and 7.65x43mm and have had no problems whatsoever.

    In fact, my all time best group with my stock Arg. 1909, 7/8" 5 shot/100 yds, was fired with mixed headstamp reformed 1909s.

    I have never has any case failures. I do aneal after forming.
    sigman2

    Retired
    NRA Patron Member
    03 C&R Holder

    Forever searching for my father's M1 Garand SA 893999.

    In honor of my father, Howard C. Ricks, 4th Marine Division - Roi-Namur, Saipan, Tinian & Iwo Jima. 85 years and still going strong!

  7. #5
    FREE MEMBER
    NO Posting or PM's Allowed
    Bob S's Avatar
    Join Date
    Nov 2006
    Last On
    11-25-2012 @ 11:47 PM
    Location
    Northern Virginia USA
    Posts
    76
    Local Date
    03-28-2024
    Local Time
    05:43 PM
    I have been reloading ex-blank cases since the late 60's; mostly for cast bullet loads, but not all. I pulled out the cardboard closure piece, dumped the flash powder, used a marlinspike made from an EMD diesel engine valve stem to partly remove the roll crimp, then ran the primed cases through a FL sizing die with the decapping pin removed. Instant primed cases. Most of those cases are still going strong today.

    Sometime later, I came across a bunch of blanks with "MATCH" headstamps. I wrote off to Dope Bag about my "Match-grade blanks", and this is the response form Chuck Suydam:



    Resp'y,
    Bob S.
    Last edited by Bob S; 06-07-2009 at 10:07 PM.

  8. #6
    FREE MEMBER
    NO Posting or PM's Allowed
    Wink's Avatar
    Join Date
    Mar 2009
    Last On
    04-19-2013 @ 12:21 PM
    Location
    Central Mich.
    Posts
    15
    Local Date
    03-28-2024
    Local Time
    06:43 PM
    Live blanks? 1903? Might be interested in a bunch as they work VERY well with my golf ball launcher and can be used in my f/a 1919A4. Finds at gun shows are sparse and WAY too expensive to shoot. TIA

  9. #7
    FREE MEMBER
    NO Posting or PM's Allowed
    musketshooter's Avatar
    Join Date
    Mar 2009
    Last On
    12-21-2019 @ 10:51 AM
    Location
    Montana
    Posts
    142
    Local Date
    03-28-2024
    Local Time
    06:43 PM
    I don't understand why you are destroying them. They are non-corrosive and would be an asset to sell if you need money for other club stuff. Most blanks dated in that range were made up from regular fired ctgs. The primer pockets were heavily swaged to allow for insertion of the new primers. The pockets are usually to large to safely reload. If the crimp looks a little wider than normal, that is what you have.

  10. #8
    Legacy Member seabee73's Avatar
    Join Date
    Mar 2009
    Last On
    05-03-2022 @ 04:24 AM
    Posts
    10
    Local Date
    03-28-2024
    Local Time
    06:43 PM
    I've removed the crimp with a screwdriver blade, resized with the decap pin removed, loaded with 47g of 4895, 150g surplus bullets, retaining the original GI primer. Used them for plinking, fun rounds with no problems. Shot hundreds of them. Don't waste those primers!

  11. #9
    FREE MEMBER
    NO Posting or PM's Allowed
    Wink's Avatar
    Join Date
    Mar 2009
    Last On
    04-19-2013 @ 12:21 PM
    Location
    Central Mich.
    Posts
    15
    Local Date
    03-28-2024
    Local Time
    06:43 PM
    1903! I meant to type M1909! Seriously, I could use some if the price isn't too bad. Last good batch I found at a gun show a couple years ago I grabbed 400 for $60-70 w/a can. Early opening morning and I snagged 'em quick! Use the money to get pull-downs from Bartletts, he still shows LC as available.

  12. #10
    Legacy Member CarlC's Avatar
    Join Date
    Mar 2009
    Last On
    05-01-2022 @ 01:49 PM
    Location
    Colorado front range
    Posts
    17
    Real Name
    Carl
    Local Date
    03-28-2024
    Local Time
    04:43 PM
    Thread Starter
    I've loaded up a small assortment of cast loads as well as 20 rounds of M2 Ball spec loads. I'll give them a try over the week.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. Reloading for AR in .223
    By JohnMOhio in forum Ammunition and Reloading for Old Milsurps
    Replies: 18
    Last Post: 07-03-2009, 12:07 AM
  2. Reloading 30-06 Blanks
    By fuzybum in forum Ammunition and Reloading for Old Milsurps
    Replies: 4
    Last Post: 06-02-2009, 12:38 AM
  3. T & T Reloading.... ?
    By MEHavey in forum Ammunition and Reloading for Old Milsurps
    Replies: 2
    Last Post: 05-11-2009, 06:19 PM
  4. .30-06 blanks
    By PhillipM in forum The Watering Hole OT (Off Topic) Forum
    Replies: 2
    Last Post: 05-04-2009, 03:51 PM
  5. Reloading Blanks for semi-autos
    By diopter in forum Ammunition and Reloading for Old Milsurps
    Replies: 2
    Last Post: 08-15-2008, 11:12 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks