+ Reply to Thread
Results 1 to 5 of 5

Thread: Load for S@W Mod.52

Click here to increase the font size Click here to reduce the font size
  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    SUB VET II's Avatar
    Join Date
    Mar 2009
    Last On
    06-21-2013 @ 11:55 PM
    Location
    Concord CA.
    Posts
    43
    Local Date
    03-28-2024
    Local Time
    07:06 AM

    Load for S@W Mod.52

    Has anyone had experience loading the Hornady 148gr HBWC for the 52? If so; good or not so good? Currently using 2.8 gr. BE with ww primer. Results leave a little to be desired. With the Speer and Fed Match its a one hole group at 25yds. Off the Bench of course. Thanks in advance.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    Sid's Avatar
    Join Date
    Mar 2009
    Last On
    11-26-2009 @ 11:59 AM
    Location
    Havertown, Pa.
    Posts
    51
    Local Date
    03-28-2024
    Local Time
    09:06 AM
    I had one of these pistols for many years and it was the most accurate handgun I have ever owned. Recoil was mild and it was a real pleasure to shoot. The spent cases also landed nearby so it was easy to pick them up. The load I used was 3.1 grains of # 231 with a 148 grain hollow base wadcutter bullet. You will have a great time with this gun.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    Jerome Cooper's Avatar
    Join Date
    Mar 2009
    Last On
    09-26-2014 @ 11:04 PM
    Posts
    55
    Local Date
    03-28-2024
    Local Time
    10:06 AM

    M52 Loading

    For many years I have enjoyed shooting this pistol. It is truly a classic and it can work well with HBWC's, but it is possible that HWBC's do somewhat better in target revolvers. I however realized much success with the H&G #251, (not a HB),but a BBWC weighing 148 grains. With an H&G mold the bullet uniformity and quality is amazing. The 2.7-2.8 grains of Bullseye loading is a/the classic loading for the 38 special, (with a H&G #50 style WC) but I found the load to be a trifle warm because of the seating of the #251 bullet flat flush with the case mouth. Reducing the charge softened the recoil and improved the grouping, but I developed and finally settled on 2.6 grains of 700X which consistently shot the best groups for me...perhaps because it is a bit bulkier and improved the loading density. I sometimes used mil spec brass which was thicker so had to size my castings at .356. When using regular commercial brass such as WW or Rem, I sized bullets to .357. I lubed one groove(the bottom) only. I used two different lubes; my own mix of beeswax and vaseline or the old NRA 50/50 Alox/beeswax formula. Both shot the same. I'm sure that many other powder combinations are also possible. You are abolutely corrrect; off the bench at 25 yards it is one hole in the 10 ring all day long. It can be 1.0"-1.5" At 50 yards if you handweigh the bullets and the powder charges individually, adjust your trigger pull carefully, do a lot of synced breathing and loads of practice. All that takes a lot of patience and devotion; A shooting friend of mine did it, but it takes/took a lot of time as well. I'm currently working with a M952 which is a 9mm and supposedly in the same league as our 52's. We'll see. Good luck with/enjoy your targetmaster. JC

  6. #4
    FREE MEMBER
    NO Posting or PM's Allowed
    MK111's Avatar
    Join Date
    Mar 2009
    Last On
    09-02-2015 @ 12:48 AM
    Location
    SW Ohio
    Posts
    98
    Local Date
    03-28-2024
    Local Time
    10:06 AM
    If you use mixed brands of brass in the S&W 52 you may have problems with functioning as some brands of brass is thicker than others. In this case use the Lee Factory Crimp Die. It resizes the case after the bullet is seated to what Lee calls high factory specs for loaded rounds. Have never had a problem again. Just don't load too hot with HBWW's as you can blow the bases off and ring you basrrel on the next round.

  7. #5
    FREE MEMBER
    NO Posting or PM's Allowed
    Larry Gibson's Avatar
    Join Date
    Mar 2009
    Last On
    12-04-2017 @ 04:06 PM
    Location
    University Place, WA
    Posts
    40
    Local Date
    03-28-2024
    Local Time
    07:06 AM
    As mentioned the classic 2.7 load of Bulleseye under a HBWC and with PB'd WCs works very well in most revolvers. In the M52 with the bullets seated flush things can be a little different. A lot depends on the thickness of the the skirt and the depthof the HB along with the alloy used. With the soft lead swaged Hornady's I suggest starting at 2 gr and working up in 1/10 gr increments until accuracy goes south. In the event that accuracy is still poor to begin with at 2 gr and remains that way....well some guns do have their preferences so just get the Speer HBWCs.

    Larry Gibson

+ Reply to Thread

Similar Threads

  1. .310 Cadet Load
    By Amatikulu in forum Martini Henry Rifles
    Replies: 24
    Last Post: 08-26-2011, 10:13 AM
  2. Load for 1903
    By SUB VET II in forum Ammunition and Reloading for Old Milsurps
    Replies: 9
    Last Post: 11-07-2009, 02:07 PM
  3. ,308 Garand load
    By Busterman in forum Ammunition and Reloading for Old Milsurps
    Replies: 7
    Last Post: 08-06-2009, 11:38 PM
  4. NM AR-15 69 SMK Load ?
    By Weez556 in forum Ammunition and Reloading for Old Milsurps
    Replies: 3
    Last Post: 03-26-2009, 02:53 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks