+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 25

Thread: SMLE No1 MkV Restoration (Part's 1 thru 7)

Click here to increase the font size Click here to reduce the font size
  1. #1
    Contributing Member
    bigduke6's Avatar
    Join Date
    Jul 2008
    Last On
    03-13-2024 @ 07:42 PM
    Location
    North West England,UK
    Posts
    3,279
    Local Date
    03-19-2024
    Local Time
    11:23 AM

    Post SMLE No1 MkV Restoration (Part's 1 thru 7)

    After a lot of other projects etc, i thought it was time to make another start, Just a recap for those who may not have seen it in the original state and what i was left with. Dont like to repeat myself but as this should be completed in the next few weeks i thought id start at the begining and continue to its firing stage, plus some of the original pics have moved to another folder.

    It was bought (with out seeing ) for the action ( advertised as a sporterized SMLE £60),
    I was under the impression i was getting No1 Mk111, and not one to complain I kept it.

    Before and after a strip down with the parts that would go again.











    At this stage, i needed a few things, all woodwork, nose cap + spring and plunger, mag cut off, a rear sight and barrel.

    As the action had undergone some major work by Bubba, i cleaned up the Breeching up ring, and reblued this part along with the top of the charger bridge and the bottom of the mag. (rust blue) (recipe at bottom).







    You can still see bubba,s work regarding the hardened pin,or screw he has used to plug a hole he drilled, the bluing took to the soft center but reluctant to to take to the side, i had stop the process there as the match was perfect.
    Last 2 pics above show the action with the mag cut off, i purchased this with screw, and the plunger and spring for the nose cap last year at the War and Peace show,from:

    D S Solutions DS-Solutions
    Very helpfull and freindly to deal with

    Rust Blue: I use a salt solution (Salammonaiac), area to be done has to be clean, apply with a paper towel etc, and leave to rust, in some cases i leave a soaked towel on the area until dry than remove, once rusted, boil in distilled water approx 20 mins, the area then needs the black oxide removing with a soft wire brush, steel wool or scour pad. the whole process has to be repeated approx 3 or more times for best results.

    (Tip: after cleaning the area, i tend to clean it again with the solution and then after it has dried start the process.)

    Patience is required with rust blueing, you can speed it up, but for the times i do it, i use mother nature. Its a hit and miss affair in the begining,I strongly recomend testing on scrap before your confident to use this process on your pride and joy, i started to test on old barrels for the best solution, when to boil, how long to leave to rust etc.

    I would recomend the following book: Firearm Blueing & Browning by R.H. Angier
    a must for DIY man.

    Will try and get part 2 posted in the next few days.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by bigduke6; 01-03-2012 at 08:06 AM. Reason: Missed part of the blueing procedure

  2. The Following 6 Members Say Thank You to bigduke6 For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Administrator

    Site Owner
    Badger's Avatar
    Join Date
    Oct 2006
    Last On
    @
    Location
    Toronto, Canada
    Age
    75
    Posts
    12,940
    Real Name
    Doug
    Local Date
    03-19-2024
    Local Time
    07:23 AM
    My Videos in Video Club
    12
    Very interesting read ...

    Thanks for posting ...

    Regards,
    Badger

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-19-2024
    Local Time
    06:23 AM
    There's a project for The Patient One!

    Lou

  7. #4
    Contributing Member
    bigduke6's Avatar
    Join Date
    Jul 2008
    Last On
    03-13-2024 @ 07:42 PM
    Location
    North West England,UK
    Posts
    3,279
    Local Date
    03-19-2024
    Local Time
    11:23 AM
    Thread Starter

    SMLE No1 MkV Restoration (Part 2)

    Continued from Part 1

    After being off work for some time and no cash coming in, i was looking at using a SMLE No1 Mk111 fore-end, and fill in the cutouts for the rear sight protector.

    Before I begin, I must point out that woodwork is not my "forte" i,m a metal man.








    That was the Fore-end done, while looking for a butt i found the original fore-end and on a closer inspection i found an old repair, hard to see in the pics but its there, and would say was done when in service and not by the previous owner.




    Next up was the butt, i had one which had come off a No4 which had had some meat taken off it.
    I know the SMLE and No 4 are different, SMLE is a lot more slender, plus i had to fit the butt plate, it wasnt going to be perfect as i didnt want to alter the butt plate, if i come across an original SMLE butt i would swap them over, sods law if i didnt sort one out now i would be waiting a long time.

    Searching through this lot i found the one i was looking for and found some other bits i was after.





    Just a quick note on the last pic above, in some cases,s i use the back of a hacksaw blade or stanley knife blade to remove old varnish.




    The butt (above) is dark as it was just cleaned in white spirit, an old repair visible this will probably be removed and re done for a better fit for the butt plate.

    The next bit was more of an experiment, i had an old forward hangaurd which was broke, which i was going use with a repro rear handgaurd i was going to get from EFD.
    I decided to square up the hand gaurd and have a go of splicing into a rear hangaurd from a No4. i didnt have anything to loose as if it did go pear shaped i could still use it.

    pics below show how a Mk111 set would be and the rear gaurd from a No4



    First job was to square off the end and mark out, then a bit of trimming.




    Next was to square up the No4 rear gaurd, and mark out.






    At this stage it was a case of trim, fit ,trim, fit etc





    That wraps it up for this stage, still a lot of work to do, the hangaurd needs the cut out at the rear and the barrel clip fitting, then its a case of glueing and sanding, linseed oilicon applying etc.
    part 3 Woodwork should be finshed and will looking at relining a barrel to .22. (thats if i can get the donor barrel of its host) which needs a new barrel.

    The reason for the .22 was due to the work that bubba had done, i decided to go for .22. better safe than sorry.
    Last edited by bigduke6; 06-10-2010 at 06:38 PM.

  8. The Following 5 Members Say Thank You to bigduke6 For This Useful Post:


  9. #5
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-19-2024
    Local Time
    06:23 AM
    This is turning out to be quite a nice project! Keep up the good work!

    And, if you're more a metalworker than a wood worker, I can then only imagine what magic you can do with metal...

    Lou

  10. #6
    Contributing Member
    bigduke6's Avatar
    Join Date
    Jul 2008
    Last On
    03-13-2024 @ 07:42 PM
    Location
    North West England,UK
    Posts
    3,279
    Local Date
    03-19-2024
    Local Time
    11:23 AM
    Thread Starter
    Thanks lou,

    Hope to get the other parts posted, next week.

  11. #7
    Contributing Member
    bigduke6's Avatar
    Join Date
    Jul 2008
    Last On
    03-13-2024 @ 07:42 PM
    Location
    North West England,UK
    Posts
    3,279
    Local Date
    03-19-2024
    Local Time
    11:23 AM
    Thread Starter

    SMLE No1 MkV Restoration (Part 3)

    I was wanting to get the woodwork finished and the barrel started in this part but had a few delays and the doner barrel i was going to relign from a 1966, 7.62mm Ishapore 2A1, turned out to be OK (and am now the owner).

    With the barrel on hold thought i,d see what it all looked like with the action.

    Where i left off last time the handgaurd was in its finishing stage, and i did the cut out at the rear. (still to finish this and the barrel clip but left it until i knew what barrel was going on)

    After a few coats of Boiled linseed oilicon,




    Two things i had to remove from the old fore-end, the stock bolt plate, and the gaurd screw bushing.





    after fitting these to the new fore-end it was a case of putting it together to see how it looked ...








    The butt i wasn,t happy with (first thing to be replaced when i find one) if i do use it, will need to remove some material to allow the safety to operate and to cut the recess for the butt disc.

    The last pic shows that the hangaurd still needs work, but will wait till i get the barrel on.

    Am awaiting for the extra barrel band, and while I,v ordered this and have done the handgaurd, i may have a original band and rear handgaurd on the way.

    Sods law once you make a start, things start coming to the surface.

    Last thing is the rear sight, have a few pics on hand of the original, so plan on making this but will use something as a stand in. If bubba had not had his way, then spending the cash on a sight from EFD would be worth it but as its never going to be perfect I will bide my time,
    Am still tempted to put a barrel on chambered to .30 M1icon carbine, it would be single shot and I have a bolt head and barrel, everything else would be unchanged.

    Hope to be finished in part 4, but its suprising how many photo,s you end up with.

  12. The Following 10 Members Say Thank You to bigduke6 For This Useful Post:


  13. #8
    FREE MEMBER
    NO Posting or PM's Allowed
    gunner's Avatar
    Join Date
    May 2009
    Last On
    09-02-2018 @ 08:20 AM
    Location
    Bavaria, Germany
    Posts
    1,657
    Local Date
    03-19-2024
    Local Time
    11:23 AM
    Bigduke,

    all the parts are a great reading! You made a great job,congratulations!!!

    Regards

    Gunner

  14. #9
    Contributing Member
    bigduke6's Avatar
    Join Date
    Jul 2008
    Last On
    03-13-2024 @ 07:42 PM
    Location
    North West England,UK
    Posts
    3,279
    Local Date
    03-19-2024
    Local Time
    11:23 AM
    Thread Starter
    Thanks Gunner,

    The main idea behind it, was to show what can be done to bring a bubba case back to a useable rifle with what you have on hand and then add the original parts when they turn up, also to demonstrate that all is not lost, even if it requires a reduction or change of calibre, ( i must stress am only reducuing the calibre as a safety precaution, am more than confident it will hold up to the .303 but am a firm believer in better safe than sorry)
    posting it in parts i thought was better than one big thread, and helps me to get the photos organized as there was a lot to choose from. hope to get the last part posted when the barrel band arrives, also the last post shows how to recycle an old .308 target barrel.....

  15. Thank You to bigduke6 For This Useful Post:


  16. #10
    FREE MEMBER
    NO Posting or PM's Allowed
    gunner's Avatar
    Join Date
    May 2009
    Last On
    09-02-2018 @ 08:20 AM
    Location
    Bavaria, Germany
    Posts
    1,657
    Local Date
    03-19-2024
    Local Time
    11:23 AM
    Bigduke,

    this is a good idea! And i hope it will be a inspiration for some of the guys to do such an project by themselve and save a poor old rifle from being only cheap scrap. Thank you.

    Regards

    Gunner

+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. G43 Restoration
    By m4a3sherman in forum The Restorer's Corner
    Replies: 17
    Last Post: 03-17-2012, 12:29 AM
  2. The restoration, (BDL FTR), of a Bren Mk.1
    By Brian Dick in forum The Bren LMG (Light Machine Gun)
    Replies: 18
    Last Post: 12-30-2009, 08:01 PM
  3. Rock Ola Restoration
    By painter777 in forum M1/M2 Carbine
    Replies: 16
    Last Post: 10-07-2009, 11:30 PM
  4. recent restoration
    By goo in forum The Watering Hole OT (Off Topic) Forum
    Replies: 1
    Last Post: 06-25-2009, 12:29 PM
  5. 03A4 Restoration ???????
    By RGC in forum The Restorer's Corner
    Replies: 5
    Last Post: 03-22-2009, 04:04 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks