+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 13

Thread: Phosphating/Parkerising

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member paulseamus's Avatar
    Join Date
    Aug 2008
    Last On
    07-01-2020 @ 09:08 PM
    Location
    Stratham - South Western Australia
    Posts
    386
    Local Date
    04-25-2024
    Local Time
    12:17 PM

    Phosphating/Parkerising

    When re-finishing a barrelled receiver is there a technique to phosphate/parkerize both the barrel and the receiver without affecting the bore?


    Paul
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 06:06 PM
    Location
    Victoria BC
    Posts
    29,927
    Real Name
    Jim
    Local Date
    04-24-2024
    Local Time
    09:17 PM
    All we ever did was to parkerize and then after the boil out and cold water, was to oil liberally and run a real good bore brush through the bore. As if to clean. It removed the crystaline formation on the surface and everything was well. We never had any problems.
    Regards, Jim

  4. Thank You to browningautorifle For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    Bearclaw's Avatar
    Join Date
    Sep 2010
    Last On
    07-13-2016 @ 03:48 PM
    Location
    Brisbane, Australia
    Posts
    177
    Local Date
    04-25-2024
    Local Time
    02:17 PM
    Paul,

    I played around with some test barrels and oiled the bore and used some those foam ear plugs to prevent excess solution getting in, worked fine and didn't pop out when the barrel was boiled.

    Myles

  7. #4
    Contributing Member Buntlineguy's Avatar
    Join Date
    Jul 2009
    Last On
    Yesterday @ 08:27 PM
    Location
    Akron, Ohio
    Posts
    115
    Real Name
    Ronald Rose
    Local Date
    04-25-2024
    Local Time
    12:17 AM
    Corks work well. Sears hardware has them in various sizes.
    B

  8. Thank You to Buntlineguy For This Useful Post:


  9. #5
    Advisory Panel Chuckindenver's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 03:30 PM
    Location
    Denver Co
    Age
    61
    Posts
    3,155
    Real Name
    chuck
    Local Date
    04-24-2024
    Local Time
    10:17 PM
    avoid corks...use rubber stoppers on the breach, and high temp silicone for the muzzle and then pick it out after your done, make sure you clean the bore well after your done. and run a oil patch afterwards..
    been my experiance that real corks are a bear to get out they seal too good, lol.. rubber stoppers on both ends works ok, but they tend to pop out when you set them in a heated tank, air expands, and one pops out, usually the muzzle.
    warpath metal finishing contact info.
    molinenorski@msn.com
    720-841-1399 during normal bus, hours.

  10. The Following 3 Members Say Thank You to Chuckindenver For This Useful Post:


  11. #6
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    04-25-2024
    Local Time
    06:17 AM
    As someone who has no idea where to get corks or rubber plugs out here in the middle of Mauserland, but who has a drawful of foam earplugs, I find Bearclaw's suggestion brilliant!

    Patrick

  12. Thank You to Patrick Chadwick For This Useful Post:


  13. #7
    FREE MEMBER
    NO Posting or PM's Allowed
    Bearclaw's Avatar
    Join Date
    Sep 2010
    Last On
    07-13-2016 @ 03:48 PM
    Location
    Brisbane, Australia
    Posts
    177
    Local Date
    04-25-2024
    Local Time
    02:17 PM
    Patrick, I placed the earplugs in after I boiled the barrel in water for a final degrease before putting it in the solution. As the barrel cooled caused a vacum and it seemed to hold them in place. But I like Chuck's idea. Maybe smear a bit of silicone on the earplugs.

    Myles

  14. #8
    FREE MEMBER
    NO Posting or PM's Allowed
    gunner's Avatar
    Join Date
    May 2009
    Last On
    09-02-2018 @ 08:20 AM
    Location
    Bavaria, Germany
    Posts
    1,657
    Local Date
    04-25-2024
    Local Time
    04:17 AM
    Where to get the parkerizing stuff here in Mauserland?

  15. #9
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 06:06 PM
    Location
    Victoria BC
    Posts
    29,927
    Real Name
    Jim
    Local Date
    04-24-2024
    Local Time
    09:17 PM
    I can't say Gunner, you may have to mix it yourself. I'm sure someone here has a recipe.
    Regards, Jim

  16. #10
    FREE MEMBER
    NO Posting or PM's Allowed
    gunner's Avatar
    Join Date
    May 2009
    Last On
    09-02-2018 @ 08:20 AM
    Location
    Bavaria, Germany
    Posts
    1,657
    Local Date
    04-25-2024
    Local Time
    04:17 AM
    Thank you! Hope it has ingredients that are allowed to us to buy. But i hope ill get a recipe, thanks!

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts