+ Reply to Thread
Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 36

Thread: Questionable reduced loads with slow rifle powder. Should I be concerned?

Click here to increase the font size Click here to reduce the font size
  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    Swagman00's Avatar
    Join Date
    Mar 2012
    Last On
    03-26-2012 @ 01:39 AM
    Location
    East Bay, CA
    Posts
    7
    Local Date
    03-28-2024
    Local Time
    02:36 AM

    Questionable reduced loads with slow rifle powder. Should I be concerned?

    So I was talking to an old friend that is thinking of trying his first 20 round batch of reloaded 7.62x54R. At first he thought he was OK, but now has second thoughts after not using specified reload data. I told him to hang on for a bit until I could find out myself.

    His loads are 180 gr gas checked pan lubed hard cast RNL .303 Britishicon that have already been bore slugged. They're .001 over so he's good in that department. He's also using unloaded unfired steel milsurp berdan primed cases with 32 grains of Varget (roughly a 70% load) and TP as a buffer rather then dacron or kapok. I know Vargant is a rather slow powder and have read several articles about the dangers under-loading slow burning rifle cartridges. The idea he has is to get them down to the 2000 FPS zone to prevent leading, but maintain stability.

    No laughing, hazing, heckling or damnation please. I'm just looking out for him.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by Swagman00; 03-23-2012 at 02:47 PM.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel Parashooter's Avatar
    Join Date
    Dec 2008
    Last On
    Today @ 02:24 AM
    Location
    Connecticut
    Age
    79
    Posts
    677
    Local Date
    03-28-2024
    Local Time
    05:36 AM
    While "detonation" with reduced loads of slow powders remains a controversial topic (probably happens, but very difficult to reproduce in a controlled setting), your friend could make a more efficient powder choice than Varget for a load in the 2000 fps class. RL-7, 4759, and 5744 are all more effective. They take a lighter charge to produce the same velocity and burn more completely at the reduced pressure involved. FWIW, Varget isn't an especially slow powder and is therefore less likely to produce pressure anomalies in low-density loads than some of the really slow numbers.

    It's now generally considered inadvisable to use fillers of any kind in bottleneck cartridges, there being a risk that the filler will compress into a solid obstruction as it tries to pass from case body into the smaller neck. If one has to employ a filler, polyester fluff (Dacron) offers the advantage of burning/melting down to a very small volume when heated.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    02:36 AM
    I would suggest using ONLY data from proven sources and stick with it. Reduced loads can and often ore dangerous to both firer and spectators. Don't reduce below stated loads and use only recommended powders for this. Like para shooter said I wouldn't put the kapoc or dacron in a bottleneck case for filler. Lyman has a lead load book for this very thing.
    Regards, Jim

  6. #4
    FREE MEMBER
    NO Posting or PM's Allowed
    Swagman00's Avatar
    Join Date
    Mar 2012
    Last On
    03-26-2012 @ 01:39 AM
    Location
    East Bay, CA
    Posts
    7
    Local Date
    03-28-2024
    Local Time
    02:36 AM
    Thread Starter
    I knew it sounded like a bad idea. I was doing some reading and it sounds like a 70% load of H4895 without any filler is a safe bet for reduced loads.

  7. #5
    Legacy Member Calif-Steve's Avatar
    Join Date
    Mar 2009
    Last On
    10-01-2023 @ 12:52 AM
    Posts
    2,508
    Local Date
    03-28-2024
    Local Time
    04:36 AM
    I would use 5744. I don't use very low loads of Varget.

  8. #6
    Legacy Member Bruce McAskill's Avatar
    Join Date
    Mar 2009
    Last On
    01-17-2023 @ 09:10 PM
    Posts
    1,880
    Local Date
    03-28-2024
    Local Time
    04:36 AM
    Varget is in the same burn range as IMR 4064 and not much slower then 4895.

  9. #7
    FREE MEMBER
    NO Posting or PM's Allowed
    Pedersoli's Avatar
    Join Date
    Apr 2012
    Last On
    08-25-2019 @ 07:07 PM
    Location
    Port Angeles, Washington
    Posts
    1
    Local Date
    03-28-2024
    Local Time
    02:36 AM
    There is good information available on the Cast Bullet Association Inc Forum for this topic. In particular articles written by C. E. Harris.

  10. #8
    Legacy Member jarmann's Avatar
    Join Date
    Dec 2009
    Last On
    05-21-2023 @ 02:30 PM
    Location
    flanders southern nederlands
    Posts
    38
    Real Name
    Frans
    Local Date
    03-28-2024
    Local Time
    09:36 AM
    dear sirs ,
    redused loads are always made with fast burning powders (H4198 ,unique, 5744 n110 n340 2400)(pistol powders/ m1 powders ) this you find all over the differend forums and magazines ,
    allways use a keeper over the powder (dacron fluf 2/3 gn ,toilet paper kitchenroll in small amounts ,carton disk on straight walled cases ) I even use them with fmj bullets in springfield 1903a3 and the m17 mostly with N110 vitha
    this is not new, it has been done for years ,the only DANGER in this matter is DOUBLE CHARGE , and the flash over ,but that we all new allready a long time !!!!!!AND WE ALL NOW HOW TO AVOID THIS PROBLEM (weight every charge and compleet your rounds piece by piece )no TV no radio ,complete consentration on the matter, like a monk in is cell
    What we do ourselfs we mostly do better
    greetings from over the pond
    jarmann

  11. #9
    FREE MEMBER
    NO Posting or PM's Allowed
    Pyno&dyno's Avatar
    Join Date
    Mar 2010
    Last On
    02-16-2018 @ 10:36 PM
    Location
    Italy
    Posts
    39
    Local Date
    03-28-2024
    Local Time
    10:36 AM
    Hi
    I have been using reduced load on 30-06 6,5x55 and 7,62x54, initially I used to insert cotton as a filler but now I don't use it anymore. For lead bullet as suggested you should move to a pistol powder. I tested some N340 (because here is easier to find Vithavuory than American powder),then because I shoot fmj bullet I tested the N110 with very good results, the precision is matching the full load charge.

  12. #10
    Legacy Member jarmann's Avatar
    Join Date
    Dec 2009
    Last On
    05-21-2023 @ 02:30 PM
    Location
    flanders southern nederlands
    Posts
    38
    Real Name
    Frans
    Local Date
    03-28-2024
    Local Time
    09:36 AM
    buen giorno
    I load 26 gn n110 on a 168 gn privi fmj bullet for the 30/06 1903a3 smith corona velocity 636 m/sec gives same results as sr4759 powder with same bullet
    a other few examples
    us krag 18 gn n110 HN ( haenel en natterman) .308 copper plated high speed 180 gn bullet best groups at 100 m
    in danish krag 1889 17 gn n110 .323 190 gn HN bullet also with 17 gn N340 same bullet same results at 100m cases made from 45/90 starlight
    winchester musket 1873 n340 7gn on 200 gn leadbullet (shoots like a .22 rifle) nice groups at 100 m
    a la prossima volta
    greetings from the same site of the pond but a little more to the north/west
    jarmann

  13. The Following 2 Members Say Thank You to jarmann For This Useful Post:


+ Reply to Thread
Page 1 of 4 1 2 3 ... LastLast

Similar Threads

  1. Hello, again! Rifle mag 8x57 hot loads
    By jon_norstog in forum Ammunition and Reloading for Old Milsurps
    Replies: 20
    Last Post: 11-28-2011, 08:16 AM
  2. Reduced loads for Milsurps
    By aprayinbear in forum Ammunition and Reloading for Old Milsurps
    Replies: 5
    Last Post: 07-29-2010, 07:45 PM
  3. Smokeless Powder out of oa cordite Rifle
    By EnfieldNutt84 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 3
    Last Post: 02-05-2010, 11:52 PM
  4. Questionable 30-rounder
    By dnikkor in forum M1/M2 Carbine
    Replies: 3
    Last Post: 11-25-2009, 05:25 PM
  5. ? On Shipping Black Powder Rifle
    By DavidS in forum Black Powder
    Replies: 1
    Last Post: 09-01-2009, 12:38 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks