+ Reply to Thread
Results 1 to 8 of 8

Thread: Seeking opinions/advice restocking Krag Rifle

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member jdmcomp's Avatar
    Join Date
    Dec 2009
    Last On
    01-01-2024 @ 03:35 PM
    Location
    E. Tenn
    Posts
    147
    Local Date
    03-28-2024
    Local Time
    07:05 AM

    Seeking opinions/advice restocking Krag Rifle

    I purchased a Kragicon rifle (1890) that had been refinished both metal and wood. And sadly, the metal appears to have been in first rate shape before refinish with no pits or scratches showing. The stock shows several repairs where wood was replaced. The stock was finished with a poly finish and shines. The story was that the rifle was used in the movie about the SpanAm war. Could be but I bought the gun and not the story. As I remember, I paid $250 for it. It will never be a collectors gun due to the metal refinish but I still would like it to look as original as possible.

    Boyds makes a replacement stock and I am considering restocking due to the wood repairs to the original. I could strip the originals poly finish and put BLOicon on it but the wood repairs are quite visible. I am seeking the opinion/advice of the board as to this action. Also, I seek anyone who has experience using a Boyds Krag stock. (I have used their commercial stocks without problems and find the products a good buy for the money, fitting perfectly and finished as I like them.) Pitfalls and problems? Thanks in advance, John McP
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    noelekal's Avatar
    Join Date
    May 2011
    Last On
    01-31-2020 @ 10:49 AM
    Location
    Texas
    Posts
    19
    Local Date
    03-28-2024
    Local Time
    06:05 AM
    I'd probably try the stripping route first but with raw linseed oilicon. Apparently Springfield Armory used raw linseed oilicon to finish stocks in that era. It does cure to a slightly reddish hue as may be found on original stocks.

    It'd be worth it just for the experience and knowledge gained from the stock rehab effort.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member Salt Flat's Avatar
    Join Date
    Nov 2011
    Last On
    Yesterday @ 03:57 PM
    Location
    USA
    Posts
    760
    Local Date
    03-28-2024
    Local Time
    05:05 AM
    I agree. First of all the wood that is being used for reproduction stocks (in most cases) is inferior in grain and color to the original wood Spirngfield Armory used. There is a lot to be said for saving an original stock, even if repaired and refinished. Also my experience with Boyds---The C stock that I got from Boyds was the worst piece of wood I've ever seen. It was light colored sap wood that was about a 1/4 inch fat everywhere. It didn't even work like hardwood. Show us a picture or two of what you have to work with. Salt Flat

  6. #4
    Legacy Member jon_norstog's Avatar
    Join Date
    Mar 2009
    Last On
    11-01-2021 @ 12:41 AM
    Location
    Portland, Oregon
    Age
    78
    Posts
    582
    Local Date
    03-28-2024
    Local Time
    05:05 AM
    +1 on that, John. If you can rescue the old wood, use it. As for the metal, you could do a bead blast and blue, or maybe parkerize. I've seen both done and they look good on a beater rifle. Good luck!

    jn

  7. #5
    Legacy Member jdmcomp's Avatar
    Join Date
    Dec 2009
    Last On
    01-01-2024 @ 03:35 PM
    Location
    E. Tenn
    Posts
    147
    Local Date
    03-28-2024
    Local Time
    07:05 AM
    Thread Starter
    The old wood is ok except for the small repairs (wood match is not especially good) and a very shiny poly finish that will be the devil to remove. I have done it and I know how hard that stuff is to remove from the grain. The metal is refinished and also very shiny, no beater here, but rather the metal refinish is a bit too good (very high polish). All that said, I think I will have a go at the stock and see what it turns out to be. I recently did a K98icon (Brno RC) that had been given a shiny finish and it turned out quite well, looking very good as a laminate with BLOicon finish. Using unboiled linseed oil is not possible, as I doubt any of us will live long enough to see that harden (at least from my experience). I guess you could add some Japanicon dryer but then why not use BLOicon? The rifle is meant to be a display and shooting gun so the fact that it is not desirable as a collectors item makes it perfect. The purchase price did not hurt either.

    Thanks all for the advice. Will post pics when finished.

  8. #6
    FREE MEMBER
    NO Posting or PM's Allowed
    professor9's Avatar
    Join Date
    Jan 2013
    Last On
    05-20-2013 @ 10:34 PM
    Location
    Cranberry Township, PA
    Posts
    1
    Local Date
    03-28-2024
    Local Time
    08:05 AM
    I have an 1898 with a stock built in 1895 and the stock is very poor shape - nearly split in two at one time in it's history. I have decided to go with a repro stock and wonder if Boyd's or any other would be a good choice. I've read plus and minus comments about Boyd's.
    Thanks Prof

  9. #7
    Legacy Member Salt Flat's Avatar
    Join Date
    Nov 2011
    Last On
    Yesterday @ 03:57 PM
    Location
    USA
    Posts
    760
    Local Date
    03-28-2024
    Local Time
    05:05 AM
    Professor, Can you post a picture of your stock? Depending on how it broke it might be repairable. See my above post regarding repro stocks. I would always be in favor of saving an original Kragicon stock if possible. One of the most desirable things about a Krag IS that beautiful stock. You just can't accurately reproduce it. Here is a picture of a repaired stock that was cracked from just behind the trigger guard and going back 3-4 inches. Repair was done using epoxy and a screw. Note: Always mask areas around the crack real close to keep the epoxy off the surface. The screw was covered with a small wood plug that is under the grip area. The plug was stained very dark is hardly noticeable. I also made the forearm from the rear band forward. The original finish was mostlty retained with the exception of the repaired areas. Salt Flat

  10. #8
    Legacy Member andiarisaka's Avatar
    Join Date
    Dec 2008
    Last On
    02-22-2024 @ 04:00 PM
    Location
    Upper Appalachia aka SE Ohio
    Posts
    343
    Local Date
    03-28-2024
    Local Time
    07:05 AM
    Quote Originally Posted by professor9 View Post
    I have an 1898 with a stock built in 1895 and the stock is very poor shape - nearly split in two at one time in it's history. I have decided to go with a repro stock and wonder if Boyd's or any other would be a good choice. I've read plus and minus comments about Boyd's.
    Thanks Prof
    If you have a stock that was made in 1895, it is for a model 1892 rifle. Although an 1898 rifle would fit in one, one could peer in and see the trigger mechanism as the cut for the bolt handle is larger. I've had to some repairing myself. One 92 rifle was delivered to me broken in two at the wrist, to jagged to fix, so I bought another 1895 made rifle, it too was cracked at the thin wrist, and it had the forearm lopped off. So I repaired the crack by drilling a hole through it, then using a syringe to inject epoxy throughout the crack. A brass screw and wooden cap for it finished the repair. Then I spliced the forearm from the woefully broken stock onto the repaired stock.

+ Reply to Thread

Similar Threads

  1. Seeking advice about a DP-stamped No1Mk3
    By louthepou in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 4
    Last Post: 09-02-2012, 07:20 AM
  2. P14 Restocking - Please help
    By paulseamus in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 4
    Last Post: 10-25-2011, 09:07 AM
  3. Seeking advice about what to feed a SA M1A.
    By SGTHurley in forum Other U.S. Service Rifles
    Replies: 3
    Last Post: 03-24-2011, 10:13 PM
  4. Seeking opinions on Unertl spotting scope
    By Jeff L in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 8
    Last Post: 08-30-2009, 10:18 PM
  5. Advice and opinions needed
    By RickM in forum .22 Smallbore
    Replies: 4
    Last Post: 03-29-2009, 10:38 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks