Help me pick apart my old gal?

[garrettbragg12]

Since I have my rifle torn apart for yearly cleaning, and am waiting on the stock to come back to me, I figured I'd see what parts are "Correct" for my rifle, and which ones I'd have to replace. Can you guys take a look and lemme know? If one isn't correct, tell me what would be?

The receiver is a
2, 750, 1XX which should put her around December of '44. I know for sure she was rebarreled in 52.

The bolt and uncut oprod seem correct. The hammer seems to be Winchester. Other than that I am lost! Lemme know if y'all need better pictures of anything!

[attachment=4]ImageUploadedByTapatalk1380073322.082216.jpg[/attachment]
[attachment=3]ImageUploadedByTapatalk1380073338.314747.jpg[/attachment]
[attachment=2]ImageUploadedByTapatalk1380073350.947827.jpg[/attachment]
[attachment=1]ImageUploadedByTapatalk1380073365.965028.jpg[/attachment]
[attachment=0]ImageUploadedByTapatalk1380073378.681316.jpg[/attachment]


M1/M3 Carbine: late '44 Inland
M1 Garand: late '44 Springfield

---------- Post added at 09:52 PM ---------- Previous post was at 09:51 PM ----------

For whatever reason it is not allowing me to post photos from tapatalk?


M1/M3 Carbine: late '44 Inland
M1 Garand: late '44 Springfield

Information

Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current.

[Joe W]

Part of the fun is figuring this stuff out on your own. Get a good book such as Scott Duffs "The M1 Garand: World War ll" and go at it. In this book you will find charts that describe the correct parts for the various years of manufacture. You will also find, on page 232, a data sheet for rifle # 2720806. All the parts on this rifle would be correct for your rifle.

[SRiverrat11]

Since I have my rifle torn apart for yearly cleaning, and am waiting on the stock to come back to me, I figured I'd see what parts are "Correct" for my rifle, and which ones I'd have to replace. Can you guys take a look and lemme know? If one isn't correct, tell me what would be?



Hey Garrettbragg. I have a 3,26x,XXX and its Nov. 44 so I'm not sure where you're getting you're production dates. Try Scott Duff's red M1 Garland book. He's one of the most knowledgeable on the M1.











The receiver is a
2, 750, 1XX which should put her around December of '44. I know for sure she was rebarreled in 52.

The bolt and uncut oprod seem correct. The hammer seems to be Winchester. Other than that I am lost! Lemme know if y'all need better pictures of anything!

[attachment=4]ImageUploadedByTapatalk1380073322.082216.jpg[/attachment]
[attachment=3]ImageUploadedByTapatalk1380073338.314747.jpg[/attachment]
[attachment=2]ImageUploadedByTapatalk1380073350.947827.jpg[/attachment]
[attachment=1]ImageUploadedByTapatalk1380073365.965028.jpg[/attachment]
[attachment=0]ImageUploadedByTapatalk1380073378.681316.jpg[/attachment]


M1/M3 Carbine: late '44 Inland
M1 Garand: late '44 Springfield

---------- Post added at 09:52 PM ---------- Previous post was at 09:51 PM ----------

For whatever reason it is not allowing me to post photos from tapatalk?


M1/M3 Carbine: late '44 Inland
M1 Garand: late '44 Springfield

Hey Garret

[Joe W]

Your right about that SRiverrat11, more like Apr. 1944, per Scott Duff.

[RCS]

I have an original but well used SA 2.77 million rifle with an April 1944 barrel. This rifle came out of an estate sale in a rual area, only other weapons were a 22 rim fire and a shotgun

[RCS]

garrettbragg, I will post the data from my April 1944 rifle for you, unable to post any additional photos as I am challenged in removing the old ones and only use the photos in storage.
serial number 2770090 D 28291 32 0 65 B <> without anneal 60% original color
bolt D28287-12SA S-A1<>
barrel (side) 1SA 4 44 top D35448-28-Y-67-A-M not chromed at gas port bright bore TE 5.0
gas cyl wide base S on top lock screw single slot lock round top
rear sight Type 2 lock bar knurled knobs
follower rev 12 bullet guide forged op catch late follower arm late follower rod long fork clip latch round front
trigger housing rev 12 trigger guard milled hammer rev 5 safety SA_11
op rod D35382 9 SA no relief cut
stock SA GAW faint cartouche rear handguard has relief cut, rear band gray color
butt plate Late WW2 checkering pattern long screw blue without step

[Joe W]

Scott Duffs Data Sheet for 2720806 reads the same as the Apr. 44 that RCS posted data on. Only difference is, as this rifle is about 1 month earlier, the barrel markings are 1-SA-3-44. Also the lock screw is of the poppet valve type, though I believe either could be correct for the period. RCS can answer this for sure.

[RCS]

I believe Scott Duff stated that both types of lock screws were used throughout the war. When the grenade launcher was first issued, the special lock screw was also issued (valve type) with it.

[browningautorifle]

I believe Scott Duff stated that both types of lock screws were used throughout the war

We've even had veteran testimony that the new gas cylinder lock screw relief valve came with the launchers...the rest all had solids.

[TDH]

Correct parts? Do they fit? Do they function properly? When you squeeze the trigger does the rifle go bang, eject the case, chamber a new round and lock up? It's the correct part!
If you find a rifle out there today with all the (correct) numbered parts it in all probability is still incorrect because it is not arsenal original. Arsenal original would be somewhat of a miracle as after the first G.I. cleaning party they wouldn't be.
Scenerio of a typical G.I. party. Rifles issued. Rifles stripped and trigger groups and other parts put in bucket of solvent to soften and remove cosmoline (with a lot of elbow grease). The chance of getting the same parts back in your rifle that you took out with the parts of a dozen or more rifles in the same bucket are slim to none.

Does it fit and function? It's the right part.