Which Underwood trig housing is correct?

**colreed** · 03-02-2009 12:48 PM

Am confused by Reisch about which .U. trig housing should be on my Underwood SN 4,042,813. The one I have is a type IV stamped/braised. But should it be a type III?
Any help would be appreciated.
Thanks

Information

Warning: This is a relatively older thread
This discussion is older than 360 days. Some information contained in it may no longer be current.

**Highly Recommended** · 03-02-2009 12:48 PM

A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered. Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping. In the USA shipping is $5.00 for media mail. I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!). CLICK BANNER to send me a PM for International pricing and shipping.

Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles.

Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons

Specializing in premium ammunition and reloading components.

Your source for the finest in High Power Competition Gear.

Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.

**painter777** · 03-02-2009 01:30 PM

Colreed,
I have Underwood 4,054,680 in original condition...but with the rear sight swapped out to a adj type II. My housing is Brazed/Stamed type IV. I would think either a type III or IV could be very possible as issued.

HTH
Charlie-painter777

**colreed** · 03-02-2009 01:45 PM

I noticed at the bottom of your post reply to me, there is a button for PM, which I assume is for someone to send you an Email instead of a post reply. I've looked and looked but can't figure how to activate that. I'd like to give members the opportunity to email me from a post I made rather than reply. Can you tell me how to get my setup to allow that?
Thanks again.
Reed

**painter777** · 03-02-2009 01:57 PM

You have to go into your profile, where you set up your Avatar pic and allow PM's to me sent.
I think....still trying to work the bugs out myself.

Charlie-painter777

**painter777** · 03-02-2009 02:19 PM

Originally Posted by colreed

I noticed at the bottom of your post reply to me, there is a button for PM, which I assume is for someone to send you an Email instead of a post reply. I've looked and looked but can't figure how to activate that. I'd like to give members the opportunity to email me from a post I made rather than reply. Can you tell me how to get my setup to allow that?
Thanks again.
Reed

Go to your Personal Control Panel....
Click on the "Edit Options"
Then find the "Messaging and Notification" section...
Here you can set up your changes.

I think I helped

Charlie-painter777

**colreed** · 03-02-2009 03:07 PM

Thanks again Charlie
Found "messenging" but not "messaging and notification". Still working on it.
This is going to take some getting used to. Too fancy!

**Bruce McAskill** · 03-02-2009 03:37 PM

ColReed, The type 4 trigger housing would be correct for your serial number.

**colreed** · 03-02-2009 08:50 PM

Thank you Bruce. Good news.

**Harlan (Deceased)** · 03-03-2009 03:36 PM

Originally Posted by painter777

You have to go into your profile, where you set up your Avatar pic and allow PM's to me sent.
I think....still trying to work the bugs out myself.

Charlie-painter777

Thanks Charlie,
I set mine up to accept email and just tested it successfully.
(WITH AOL!) - Email was here in seconds.

I hope everyone will set theirs up to accept email.

**lboos** · 03-03-2009 04:55 PM

Harlan, I still cant fix it? I went to per. cont. panel, eddit opt., mesg./ notice and X the accept email, and clk. on save changes? should i have clk. on reset fields?
I think im getting to old to learn new trick's, any advice?

Thread: Which Underwood trig housing is correct?

Thread Tools

Search Thread

Display

Which Underwood trig housing is correct?

Thanks, Charlie

Thank You to painter777 For This Useful Post:

Similar Threads

correct bayonet

Correct parts on mk4 T ?

M1-D Garand, correct?

Looking for a correct PU sniper

no4 mk2 correct info?

Tags for this Thread

Posting Permissions