+ Reply to Thread
Page 1 of 5 1 2 3 ... LastLast
Results 1 to 10 of 41

Thread: Bren Mk 2 Recoil Spring Issues

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member djandj's Avatar
    Join Date
    Mar 2013
    Last On
    12-01-2021 @ 11:53 PM
    Location
    So.Cal
    Posts
    109
    Local Date
    03-28-2024
    Local Time
    06:35 AM

    Bren Mk 2 Recoil Spring Issues

    Greetings all. Question for the collective oracle. I have a 1942 Bren MK 2 (1942) rebuilt by Len Savage himself. It is chambered in 54R. Has had many issues with the main spring. His rebuild seems to use only one 3/4 in diameter sized recoil spring. When I get them from Len, they start out at about 12 inches however, after only a few hundred rounds they get crushed down to about 9 inches. I start having issues with light primer strikes and/or the trigger not resetting. I have also had issues with a couple of rounds going off with the same pull of the trigger. I am quite sure the springs he is using are too weak for the recoil on the gun. (even though I have the gas setting set at their lightest)

    Does anyone else have a MK2 in 54R? I have seen other builds using two mainsprings (larger one and then a smaller one right over the metal guide rod jutting out from the butt and trigger assembly. Any ideas? Does anyone have a source for stronger springs? Ideas as to what might cause more than one round to fire at a time?

    I have e-mailed Len a few times on this and he did send me more main springs, but I just keep replacing them and having the same problems.

    Thanks,
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-28-2024
    Local Time
    04:35 PM
    Just from the metallurgical point of view, then this is definately(?) a spring problem. No 'spring' that is made from the correct steel wire that is correctly treated should compress from 12" long to 9" long after however many cycles you state. While we don't know the mechanical complexities of your gun, this doesn't alter the facts

    As a matter of fact, I have seen a recovered Bren gun found buried on an old wartime landing ground just off the Salisbury Plain training area together with several full magazines with retuen springs that were still in serviceable, albeit not perfect, condition. The magazine springs sprung out of the base oif the magazine STILL under tension when the rust was scraped away.

    Metallurgists out there comment please..... JM?

  4. Thank You to Peter Laidler For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member Joe H's Avatar
    Join Date
    Oct 2010
    Last On
    03-21-2024 @ 03:25 PM
    Posts
    210
    Local Date
    03-28-2024
    Local Time
    10:35 AM
    djandj,

    The original MkI's had a single spring. They were replaced with the double spring. Later replacement springs for both the MKI & MkII were the double spring. Sounds like you have a bad spring. They should never compress that much. Light strikes may indicate a weak striker spring if the semi is striker fired.

    I have a MKII I converted to 54R. It uses a striker set up. Gas settings 3 / 4. I put a 1" plug behind the return spring (double spring) so that the return spring was in full compression at the end of the stroke. The length of spring compression in the semi with a striker is about 1" short of the full stroke due to the length of the striker.


    The specs for the double spring are:

    Inner 90 1/2 coil Left wire dia .036" OD .358" Free length 13.2/12.8

    Outer 68 coils RT wire dia. .048" OD .477" Free length 13.2/12.8


    You can buy them here:

    50: SPRING, return, Mk 1 - BRP CORP Store

    BREN recoil spring

    Joe
    Last edited by Joe H; 05-27-2014 at 08:24 AM.

  7. #4
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-28-2024
    Local Time
    04:35 PM
    I don't think he is using the real Bren spring/springs Joe H as they rarely give trouble or compress with age. But.....

    Just to clear up a bit of doubt here forumers......
    The reason for the double return spring was to buffer the rearward action of the breech block and piston/piston post assembly during its rearward travel. and NOT to increase the loading of the forward action of the working parts. This was because they had recently opened up the gas port of the Mk1 barrel to make it a Mk1* and also the gas regulator holes to suit. When they did this, all sorts of problems arose........ It was chaos! Now, the piston post hit the unlocking cam with such brute force that it 'bottomed-out- the piston post plunger inside the piston extension, spreading it out and making it impossible to remove from the piston post plunger spring - which also broke regularly due to it now becoming coil-bound on the damaged plunger*! After this, the breech block hit the rear gun buffer plate with such force that it cracked/broke the plate away from the collar at the rear. Anyway, to cure all of this the double springs were introduced. You'll realise that the poundage required to START the rearwards motion is similar with one or two springs but thereafter it starts to show as it buffers. It obviously works because cracked buffer plates aren't a real problem. But that is why Armourers always polish them so that you can see any hairline fractures that are about to get worse.

    * The breaking of the piston post spring problem was never really cured but was lessened with the introduction of the different length piston post plunger and adjustment of the depth of the seating in the piston post housing. Yes, that's why there are Mk2 variants of each! The broken piston post spring became a 'user' maintenance item and as such a spare was always in the spare parts tin.

    Not a lot of people know that!

  8. The Following 3 Members Say Thank You to Peter Laidler For This Useful Post:


  9. #5
    Legacy Member Joe H's Avatar
    Join Date
    Oct 2010
    Last On
    03-21-2024 @ 03:25 PM
    Posts
    210
    Local Date
    03-28-2024
    Local Time
    10:35 AM
    Quote Originally Posted by Peter Laidlericon View Post
    I don't think he is using the real Bren spring/springs Joe H as they rarely give trouble or compress with age. But.....

    * The broken piston post spring became a 'user' maintenance item and as such a spare was always in the spare parts tin.

    Not a lot of people know that!
    Peter,

    Definitely not original Bren springs. Maybe they were wound using the wrong grade of wire.

    Very interesting info. I wondered why a heavy spring like the piston post spring would be in the spare parts tin for user replacement.

    Joe

  10. #6
    Advisory Panel Brian Dick's Avatar
    Join Date
    Apr 2008
    Last On
    03-25-2024 @ 05:18 PM
    Location
    Edgefield, SC USA
    Posts
    4,038
    Local Date
    03-28-2024
    Local Time
    10:35 AM
    See if you can get some good springs from Wolff Gunsprings. They won't steer you wrong.

  11. #7
    Legacy Member djandj's Avatar
    Join Date
    Mar 2013
    Last On
    12-01-2021 @ 11:53 PM
    Location
    So.Cal
    Posts
    109
    Local Date
    03-28-2024
    Local Time
    06:35 AM
    Thread Starter
    Quote Originally Posted by Joe H View Post
    djandj,

    The original MkI's had a single spring. They were replaced with the double spring. Later replacement springs for both the MKI & MkII were the double spring. Sounds like you have a bad spring. They should never compress that much. Light strikes may indicate a weak striker spring if the semi is striker fired.

    I have a MKII I converted to 54R. It uses a striker set up. Gas settings 3 / 4. I put a 1" plug behind the return spring (double spring) so that the return spring was in full compression at the end of the stroke. The length of spring compression in the semi with a striker is about 1" short of the full stroke due to the length of the striker.


    The specs for the double spring are:

    Inner 90 1/2 coil Left wire dia .036" OD .358" Free length 13.2/12.8

    Outer 68 coils RT wire dia. .048" OD .477" Free length 13.2/12.8


    You can buy them here:

    50: SPRING, return, Mk 1 - BRP CORP Store

    BREN recoil spring

    Joe

    Fantastic info here Joe. See I definitely think that I am missing a spring. Shouldn't the MK2 have one larger 3/4" recoil spring and then a small diameter spring right along the guide rod? I only have ONE spring back there. Where is the striker spring supposed to go? Cause I think I don't have one.

    Can anyone post pics of their MK2 disassembled with the springs in place? I'm pretty sure I have only one spring back there.
    Last edited by djandj; 05-28-2014 at 12:09 AM.

  12. #8
    Legacy Member Joe H's Avatar
    Join Date
    Oct 2010
    Last On
    03-21-2024 @ 03:25 PM
    Posts
    210
    Local Date
    03-28-2024
    Local Time
    10:35 AM
    D,

    There are two common types of semi conversion. Hammer fired which uses a hammer as part of the trigger group to fire the gun. It has no striker or striker spring. The striker fired semi uses a striker placed behind the carrier. It has a separate spring and is fired directly from the original Bren fire control group.

    I don't know which type Len Savage builds. I doubt you are missing a spring. A weak return spring could cause the problems you are experiencing in either type of build.

    Joe

  13. #9
    Legacy Member WallyG.'s Avatar
    Join Date
    Jan 2008
    Last On
    05-22-2022 @ 11:10 AM
    Location
    Heart of Dixie
    Age
    62
    Posts
    126
    Local Date
    03-28-2024
    Local Time
    09:35 AM
    Greetings:

    I have many of Lens Brens... The Striker spring is the 3/4 inch by 12 inch spring that rides over the return rod and is immediately seen when you remove the butt group from the front/receiver. This spring is not original Bren equipment... and it has been added to the design to power the striker block forward to contact the firing pin when the trigger is puled The Original Bren recoil springs (if in fact there are two... as the kits used for these builds came with both singular MkI springs and the doubled up MkII) are contained in a tube inside of the butt stock...they load the return rod so if you can push it easily to the rear (into the butt) then this might be the first place to try and replace springs. The access point being at the rear of the butt. If your recoil springs are under powered then the bolt group is recoiling with much more force than required to reset the action and in the process is crushing the striker spring. BRP Guns in Maryland has new replacement recoil springs... or at least they did the last time I looked. Are you shooting 7.62x54r light ball or heavy ball ammo? If you are using heavy ball... I'd try some light ball and see if your new replaced spring performance is improved. Feel free to PM me if you wish to discuss in more detail.

  14. #10
    Legacy Member djandj's Avatar
    Join Date
    Mar 2013
    Last On
    12-01-2021 @ 11:53 PM
    Location
    So.Cal
    Posts
    109
    Local Date
    03-28-2024
    Local Time
    06:35 AM
    Thread Starter
    Thanks again Wally. I have ordered the springs from BRP. Will I use BOTH the springs? (seems I should) May have to turn up the gas, but that is no problem. As is, I am running at the lowest setting. (higher settings crushed the springs much quicker and allowed the bolt group to slam into the butt with enough force to pop out the wooden spline!

+ Reply to Thread
Page 1 of 5 1 2 3 ... LastLast

Similar Threads

  1. Bren and L4 spring and thread sizes
    By Peter Laidler in forum The Bren LMG (Light Machine Gun)
    Replies: 6
    Last Post: 05-13-2014, 12:20 PM
  2. Why do the Bren Mk3 and Bren MkII rear sights have the same part number?
    By Lee Enfield in forum The Bren LMG (Light Machine Gun)
    Replies: 1
    Last Post: 06-26-2012, 03:03 PM
  3. Recoil Spring Housing
    By rocky321 in forum M1/M2 Carbine
    Replies: 4
    Last Post: 11-12-2010, 03:31 PM
  4. FNP-9 Recoil Spring Solution
    By Newsfeed Hound in forum The Watering Hole OT (Off Topic) Forum
    Replies: 0
    Last Post: 02-18-2010, 08:55 PM
  5. Slide Spring Housing (Spring Tube)
    By JimF4M1s (Deceased) in forum M1/M2 Carbine
    Replies: 0
    Last Post: 11-19-2009, 12:36 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks