+ Reply to Thread
Page 1 of 6 1 2 3 ... LastLast
Results 1 to 10 of 53

Thread: My .308/7.62mm fullauto conversion- Plug & Play Success!!

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member TactAdv's Avatar
    Join Date
    Apr 2014
    Last On
    01-17-2024 @ 02:44 AM
    Location
    NE Colorado, USA
    Posts
    236
    Real Name
    Thomas T. Hoel
    Local Date
    03-18-2024
    Local Time
    09:02 PM

    My .308/7.62mm fullauto conversion- Plug & Play Success!!

    Finally got around to looking at doing a .308 conversion for my '42 Daimler Mk II fullauto gun.

    I've been picking up the various bits over the last year, finally got interested enough to put it all together,,,,litterally as it turns out. ;-))

    I've been reading with much interest the various posts of doing the .308 conversions.....with all the ups and downs, so I now feel kind of sheepish to report to you all that, for my original gun at least, this turned out to be a "plug & play" exercise........not sure what to feel about that bit of luck but I'll report on my affair here.....

    My receiver/gun as I said, and have posted several pictures around other posts herein, is a factory original condition Daimler Mk II from 1942, so that may/may not have turned out to be an important data point in this....

    I am using one of the long-ago imported "South African"/DENEL/Lyttleton Eng. 7.62mm barrels that were new made for the SADF conversions there. Many of you seemingly have the same barrels.

    I had been holding off on this project because, stupid me, I never really looked at the damn barrel carefully when it came in except to note the R1/FAL flash hider they used, which I think is a nice visual change for the BREn. Then one of you pointed out here that these barrels are markedly differently constructed in the that the barrel shank end is cut back, and chambered accordingly, to permit use of the standard .303 bolt with horns. I had been thinking I'd need to machine the barrel base for the normal .303 bolt, machine in the ramp to accommodate the feed horns a la the .303 barrels. That was a major discovery.... ;-))

    In this particular combination of receiver & S.A. 7.62mm barrel, I was very lucky I think in that the combination breached up tight on the first try, and the bolt locked perfectly, with both the currently installed barrel lock and bolt locking shoulder. With that bit of luck, I checked the head-spacing and was in luck again. I swapped in a S.A. 7.62mm extractor into the normal .303 bolt it had in there, and that was it.

    I am using unmodified Bulgy ZB-39 mags. I have read a lot here about using them for various things but wanted to try them first as-is. They took the full 25rds no problems. I was also lucky in that they locked in perfectly with the Mk II mag catch I had installed......

    I decided to try some Russianicon "Brown Bear" steel case .308 I have lots of. See pictures below. The whole thing went together Plug & Play style.......I fired 160rds in various semi-auto and fullauto shooting, with only a couple of things to note.

    As JoeH here pointed out, occasionally, I had the last round fail to get picked up out of the magazine. It was an intermittent thing, maybe 20% of the time. Interestingly, when that happened, leaving that single round in there, the gun would fire it if cocked again.

    No failure to chamber or fire at any time, other than as above for the last round. I tried both gas port position #1 & #2. Both ran it fine, though #2 seemed, with this .308, to run more smoothly and I am guessing at about 600RPM or so.......I'll think about as I shoot it further. So far, so good.

    Here are some pictures; I'll get live fire video next time out.
    -TomH

    Attachment 63376Attachment 63377Attachment 63378Attachment 63374Attachment 63375Attachment 63373
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. The Following 4 Members Say Thank You to TactAdv For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 12:51 PM
    Location
    Victoria BC
    Posts
    29,810
    Real Name
    Jim
    Local Date
    03-18-2024
    Local Time
    09:02 PM
    We did one once using an 8mm Inglis. All we did was changed barrel(plus the minor fitting), checked headspace and carried on. Shot like yours does...used the same mag and bolt too...
    Regards, Jim

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member Joe H's Avatar
    Join Date
    Oct 2010
    Last On
    03-13-2024 @ 04:18 PM
    Posts
    210
    Local Date
    03-18-2024
    Local Time
    11:02 PM
    Tom,

    I'm green with envy. FA Bren in the US.

    Joe

  7. #4
    Advisory Panel Lee Enfield's Avatar
    Join Date
    Oct 2006
    Last On
    03-16-2024 @ 12:24 PM
    Location
    out there
    Posts
    1,820
    Local Date
    03-18-2024
    Local Time
    10:02 PM
    [QUOTE=browningautorifleicon;334679]We did one once using an 8mm Inglis. All we did was changed barrel(plus the minor fitting), checked headspace and carried on. Shot like yours does...used the same mag and bolt too...[/QUOTE]

    I assume you mean "...used the 8mm Mauser magazine and bolt too..." ?
    BSN from the Republic of Alberta

    http://www.cartridgecollectors.org/

  8. #5
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 12:51 PM
    Location
    Victoria BC
    Posts
    29,810
    Real Name
    Jim
    Local Date
    03-18-2024
    Local Time
    09:02 PM
    Quote Originally Posted by browningautorifleicon View Post
    used the same mag and bolt too...
    Like I said, used the same mag and bolt too...the ones in the gun. And, they worked fine.
    Regards, Jim

  9. #6
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-17-2024 @ 02:10 PM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,505
    Real Name
    Peter Laidler
    Local Date
    03-19-2024
    Local Time
    06:02 AM
    Must have had an extractor change surely! I have just used a .303 BB assembly in an L4 gun (not the same I agree....) with a slightly dinged/distorted drill round (to replicate it having been fired and tight in the chamber) and the 7.62 drill round just moves to the rear a couple of mm's, then upwards slightly and slips off the extractor. It's not exactly comparing like with like but the mechanics of it are the same.

    The trouble with a converted gun WITHOUT the magazine well stop inserts is that before long the gun feed lips will tear away. Or maybe this only occurs with those guns that use L1A1/FN type magazines that sit slightly deeper in order for the BB feed horns to make better contact with the smaller base rim diameter of the 7.62 cartridge

  10. #7
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 12:51 PM
    Location
    Victoria BC
    Posts
    29,810
    Real Name
    Jim
    Local Date
    03-18-2024
    Local Time
    09:02 PM
    Quote Originally Posted by Peter Laidlericon View Post
    Must have had an extractor change surely!
    It was an 8mm gun boys, the 8mm extractor...and little square mag...he didn't have any 7.62 extractors so I know we didn't change it.
    Regards, Jim

  11. Thank You to browningautorifle For This Useful Post:


  12. #8
    Advisory Panel Lee Enfield's Avatar
    Join Date
    Oct 2006
    Last On
    03-16-2024 @ 12:24 PM
    Location
    out there
    Posts
    1,820
    Local Date
    03-18-2024
    Local Time
    10:02 PM
    The 8mm Inglis Bren talk has thrown a kink into the conversation, can TactAdv show up a picture of the chamber end of his SA barrel?

    There have been 3 different recent conversations which seem to have confused the waters:

    - The L4 7.62mm series used 8mm Inglis Bren bolts & headspacing locking shoulders, so an L4 Bren barrel should lock into and headspace in a 8mm Inglis Bren assuming the use of the ZB26/30 8mm magazine.

    - The "Government" SA 7.62 conversion used a modified .303 bolt (reducing ring silver soldered onto the face of the breech bolt) with a 7.62 extractor. the .303 bolt allowed them to continue the use of .303 locking shoulders. The barrels chamber end is contoured as a .303 barrel (if I understand correctly) to allow the use of the .303 bolt. The magazine well is altered to accept metric FN mags, and an ejector block fitted with a hold open was fitted.

    - .303 barrels have been bored out and rechambered to 8mm Mauser, these barrels use un-modified .303 bolts which are fitted with 8mm Mauser extractors, newer condition Brens require some opening up of the rear of the magazine recess to accept 8mm ZB26/30 type magazines. This type of conversion "may have been" originally done at the behest of an unknown government user.

    - current civilian owners of working Brens have mixed barrels, bolts and magazines in order to obtain guns which function in a variety of calibers (8mm Mauser, 7.62x54r, 8x56r(Austrian/Bulgarian/Hungarianicon), 7.62NATO, .303 Britishicon) which are available to owners...

    ---------- Post added at 08:32 AM ---------- Previous post was at 08:26 AM ----------

    Quote Originally Posted by browningautorifleicon View Post
    It was an 8mm gun boys, the 8mm extractor...and little square mag...he didn't have any 7.62 extractors so I know we didn't change it.
    As far as I can tell, the 8mm extractor is the same as the 7.62 extractor....certainly much closer certainly than a .303 extractor..
    Last edited by Lee Enfield; 06-11-2015 at 10:30 AM.
    BSN from the Republic of Alberta

    http://www.cartridgecollectors.org/

  13. #9
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-17-2024 @ 02:10 PM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,505
    Real Name
    Peter Laidler
    Local Date
    03-19-2024
    Local Time
    06:02 AM
    You're all correct about the 7.92mm BB's and extractors and L/Sh's. These can be - and were - used un-altered in UKicon L4 guns. We know this because the EMERs stated it quite definately, the early parts lists identified them by their different drawing numbers and occasionally you'll see the 7.92 punched into them occasionally.

    I understand that a very similar extractor, marked with a small letter T (for TANK) is also useable in a 762 or 792 gun as these extractors were for use in the 7.92mm BESA gun. But as I never had anything to do with BESA guns I can't confirm it. The last BESA's went in 1966/67 or so with the last Churchill tanks

  14. Thank You to Peter Laidler For This Useful Post:


  15. #10
    Contributing Member CINDERS's Avatar
    Join Date
    Nov 2009
    Last On
    Yesterday @ 08:42 AM
    Location
    South West Western Australia
    Posts
    7,730
    Real Name
    CINDERS
    Local Date
    03-19-2024
    Local Time
    12:02 PM
    How much do the brens cost as when I win my lotto millions I intend to move the whole lot of us over to the USAicon and buy a nice flat land with no neighbourghs and set up a a super longrange where the 416/478/ma duece could play as well bring in some brens/stens top it off with 6 sniper T's and get some ammo say 15oooo should do the trick

+ Reply to Thread
Page 1 of 6 1 2 3 ... LastLast

Similar Threads

  1. Anyone had success at removing rust stains from slings?
    By painter777 in forum M1/M2 Carbine
    Replies: 9
    Last Post: 06-13-2012, 06:27 PM
  2. .303 to 7.62mm conversion question
    By Longshaor in forum The Bren LMG (Light Machine Gun)
    Replies: 4
    Last Post: 05-20-2010, 08:38 PM
  3. Amount of play on No4 Mk1 bolts
    By spinecracker in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 13
    Last Post: 08-09-2009, 11:56 PM
  4. CMP Rifle Clinic Success!!!
    By rifle guy in forum M1 Garand/M14/M1A Rifles
    Replies: 0
    Last Post: 04-21-2009, 05:14 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks