+ Reply to Thread
Results 1 to 9 of 9

Thread: Italian Vitterli 1874/1886

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Humpy70's Avatar
    Join Date
    Nov 2010
    Last On
    06-15-2021 @ 05:29 PM
    Location
    Aiken, SC
    Posts
    20
    Local Date
    03-28-2024
    Local Time
    04:22 PM

    Italian Vitterli 1874/1886

    Just became the proud owner of a 1874 Torino Arsenal rifle reworked in 1886 by Torino today.

    So far I have figured the sear surface on the striker is very dangerous and needs to be TIG welded to restore the sear surface as closing the bolt without holding back of bolt down it will sear off with a out of battery bolt handle. If I can get it to hold about a 1/2 pound on the trigger will set it off.

    That I can take care of. I will get a buddy to TIG weld the sear surface and build it up about .050" and then stone it off. I will not attempt to fire it till I am sure it is not going to sear off out of battery.


    My problem is that I can't figure out how to get the bolt out of the rifle. Just to the rear of the magazine cut off is a another area. At 3:00 on the bolt there is a slot that looks like it is for a screwdriver. On the same piece about 12:00 there is something that looks like it needs to move forward into a opening on the mag cut off ring.

    Have the bolt apart, just can figure out how to get the bolt body out??????
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 01:16 PM
    Location
    Victoria BC
    Posts
    29,838
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    01:22 PM
    Is there a key affair at the rear of the bolt, lying crosswise to the bolt? It should be hooking onto the extractor and holds the square top part from being pulled out. The key needs to be driven out to one side but it doesn't come out. Then the bolt will remove.
    Regards, Jim

  4. Thank You to browningautorifle For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member Humpy70's Avatar
    Join Date
    Nov 2010
    Last On
    06-15-2021 @ 05:29 PM
    Location
    Aiken, SC
    Posts
    20
    Local Date
    03-28-2024
    Local Time
    04:22 PM
    Thread Starter
    Found out all about it with some great pics.

    Yesterday's Weapons Forums View topic - Vetterli bolt removal - a photo tutorial

    Apparently it takes two screwdrivers pushing two different directions while rifle held in vice! ! !

  7. #4
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 01:16 PM
    Location
    Victoria BC
    Posts
    29,838
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    01:22 PM
    Don't get how you came to that , although you may have to doctor it and smooth it up to function correctly. That was the cross piece I was talking about though.
    Regards, Jim

  8. #5
    Legacy Member Humpy70's Avatar
    Join Date
    Nov 2010
    Last On
    06-15-2021 @ 05:29 PM
    Location
    Aiken, SC
    Posts
    20
    Local Date
    03-28-2024
    Local Time
    04:22 PM
    Thread Starter
    Update: I got two screwdrivers and while I pushed forward on one I pushed on the one at 3:00 and nothing. Then I realized it would probably work better pushing wards and it started to move.

    Got it up to where the screw is exposed and got out my Brownell's screwdriver kit and found the right screwdriver and after soaking started working it back and forth and it moved. Soaked it some more and it moved more and finally came out.

    I put that little sucker in a magnet parts bowl immediately and along with the block that came out after I took a steel bristle wheel to bolt and got off all the dried up oil and rust from probably a hundred years of disuse.

    I then started working on the bore and to my surprise I am seeing shiney spots appear but I don't have a 44 cal brush so I wrapped patches soaked with Ed's Red (ER) and made a bunch more passes and more shiney area appeared.

    I took a 45 cal cast bullet and tapped the ogive into the muzzle and squirted ER down the chamber end and it did not leak so I filled the entire bore all the way to the end of the chamber with ER and I am going to let it soak for a week which should loosen anything.

  9. #6
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 01:16 PM
    Location
    Victoria BC
    Posts
    29,838
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    01:22 PM
    Quote Originally Posted by Humpy70 View Post
    dried up oil and rust from probably a hundred years of disuse.
    Yes, that was where I was. Once I removed the rust it worked by fingers.

    Quote Originally Posted by Humpy70 View Post
    a 45 cal cast bullet
    I had to make ammo for mine, a center fire, and used primed 348 cases cut at the shoulder and filled with FFF black. I poured a wax plug and used a 240 gr .44 bullet and with iron sights could keep them on 18" square at 200 yd offhand. Throw in the bullet, chamber the blank and touch off. It was a decent barrel too...lots of fun.
    Regards, Jim

  10. #7
    Legacy Member Humpy70's Avatar
    Join Date
    Nov 2010
    Last On
    06-15-2021 @ 05:29 PM
    Location
    Aiken, SC
    Posts
    20
    Local Date
    03-28-2024
    Local Time
    04:22 PM
    Thread Starter
    Thought I would give you guys a update on how the resurrection is going. Got delayed due to spinal surgery and four heart procedures ending up in tripple bypass.

    As of today the Vett is sporting a M14icon front sight which now allows me to shoot POA/POI at 100 yards. Here is how I mounted it.

    Note the factory front sight is not center of the bore line. To get zeroed I had to have the new sight a tad left.









    As of today I can obtain POA/POI at 100 yards shooting a 257 Gr. Lyman cast bullet over 17.5 gr 2400. Made cases from Jamison 348 Win brass.

    Bore cleaned up beautifully.

  11. #8
    Legacy Member Humpy70's Avatar
    Join Date
    Nov 2010
    Last On
    06-15-2021 @ 05:29 PM
    Location
    Aiken, SC
    Posts
    20
    Local Date
    03-28-2024
    Local Time
    04:22 PM
    Thread Starter
    First off to save a ton of typing do a google search for "Suicide by Italianicon Vetterli" and this will give you lots of good info and pics of what I have learned and where one needs to be to successfully reload ammo for this fine old weapon for many years to come.

    First off genuine Vetterli 10.4X47 dies can be had from CH for like $152.00. Had I known that two years ago I might have sprung for them but all I could find was 41 Swissicon dies by Lee and I have loaded about a hundred rounds with them and they will work up to a point and are about 1/4th the cost of the CH dies.

    One major problem in reloading the Vetterli has been confirmed by an avid Vetterli shooter in Italy and that is the necks on fired/resized cases don't hold the bullets well and there is a tendency for the bullets to FALL down in the case and this will result in colorful language for sure.

    Others have surmised that 44 Mag dies can be used. Yes, No and Maybe. In repeated practice the 44 Mag dies are about .003" to big so what is a body to do?

    Yesterday I ordered a Lee trim die for 41 Magnum pistol and the plan is to convert this trim die to a neck size die by opening the base to where is it .004" smaller than 44 Mag TC dies.

    Here's a pic of the problem you are likely to encounter:



    Note fired case is on the left and the new case is on the right. A close look will show the neck is really opened up on firing and what I described above happens.

    I have two fixes planned, first is I have a Lee 41 Mag trim die inbound and I will grind the inside base area to where it will resize the neck down about .004 smaller than the Lee or 44 Mag dies will which should have as much grip as a 7.62 NATO round on their bullets.

    I also have inbound a set of 348 Winchester FL dies and I plan on cutting off the top of the FL die and opening it up to the small dimension as I am also seeing a gradual expansion of cases bases and a few don't want to open and release the fired case and have to be tapped out with a gentle taps with a rod. Basically it will be converted to a body die that I will FL size with every few loadings to restore orginal base dimension. If it doesn't size it small enough I will remove a few thou from base of die to all case further up into the taps to squeeze it down.

    I am stress relieving necks with propane torch about every third round. Basically I try to move brass as little as possible in order to get longer case life. If I can I set things up to where the brass doesn't move over .002 on firing so it takes very min force to restore it to where I want it.

    Bottom line is has been a labor of love to resurrect this 144 year old girl to shooting condition and is worth the effort. Take a looksee at the Suicide article above for much more info and pics.

  12. The Following 3 Members Say Thank You to Humpy70 For This Useful Post:


  13. #9
    Legacy Member sshackle's Avatar
    Join Date
    Aug 2012
    Last On
    03-24-2024 @ 04:14 PM
    Location
    Anchorage, Alaska USA
    Posts
    11
    Local Date
    03-28-2024
    Local Time
    12:22 PM
    Thanks the info. I am working on getting my 1870/87 Vetterli shooting. I posted it and photos yesterday. I order a Lee die for 330 gr. .430 bullet the i plan to alter for a heeled bullet. I bought formed brass from Ammunition Artifacts.



+ Reply to Thread

Similar Threads

  1. Photo of 1874 Gras bolt stop screw
    By Calfed in forum Black Powder
    Replies: 3
    Last Post: 09-24-2013, 09:31 PM
  2. 'Nomadic' St. Etienne Gras 1874/80 carbine.
    By Anzac15 in forum Milsurps General Discussion Forum
    Replies: 7
    Last Post: 08-29-2012, 12:17 PM
  3. Cleaning question: French 1874 Gras bayonet
    By Aragorn243 in forum Edged Weapons Forum
    Replies: 3
    Last Post: 02-28-2011, 08:11 AM
  4. Lebel 1886 - 93
    By rdj94a in forum Ammunition and Reloading for Old Milsurps
    Replies: 1
    Last Post: 05-11-2010, 07:40 PM
  5. New Rifle 1886
    By 1941WillysMB in forum Other U.S. Service Rifles
    Replies: 0
    Last Post: 04-15-2009, 04:26 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks