+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 26

Thread: Bought a 1903 Turkish Mauser

Click here to increase the font size Click here to reduce the font size
  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    nuget102's Avatar
    Join Date
    Dec 2016
    Last On
    01-26-2020 @ 02:15 PM
    Location
    Kentucky, USA
    Posts
    23
    Local Date
    03-29-2024
    Local Time
    09:03 AM

    Arrow Bought a 1903 Turkish Mauser

    I bought a 1903 Turkishicon Mauser yesterday. It was manufactured in 1937 and has a 29.5" barrel.

    It's in rough shape, and costed me around $175. It has the cleaning rod, and comes with a sling. The guy I bought it from says it fires and loads okay. I tried loading it when I got home (didn't have any 8mm ammo on me. And yes, this one was modified to be 8mm by the Turks.) and I had a problem.. The bullets wouldn't feed.

    We could feed a single bullet no problem, but more than that and it'd be difficult. To the point we had to get a screw driver and fiddle with the bullets. I'm slightly annoyed, but the gun looked okay to me. Hoping it's just a weak spring? The stock appeared to be okay, and I seen no visible rust.. But I couldn't get the floorplate out of the trigger guard, so naturally I just took the trigger guard off. And I seen rust mixed with rotten wood. I began to field strip the rifle and I found more of the same. My observation is the stock will probably need replaced eventually. Although I think it's okay for now.

    But, the bolt cycles flawlessly and easily. The safety flips without a problem. And the iron sights look okay, although i'm missing the front sight hood. I'm guessing the previous owner did nothing but routine maintenance on the gun, since all the visible areas are pristine.

    So basically my problems: floorplate won't release. I think it's a push pin and then push on the plate and slide it towards the trigger type release. But my guess, it's rusted shut. So soak it in WD-40?

    And the follower won't feed the bullets properly. It's like they get jammed in the mag, so the bolt can't even catch them. Weak spring? Or perhaps the spring was re-bent some one who doesn't know better?

    Also, here's a couple pics of the rifle. Not the best, but all I have is my cell.
    Attachment 79123 Trigger guard pins
    Attachment 79124
    Attachment 79125 The part of the stock where the trigger guard inserts
    Attachment 79126
    Attachment 79127
    Attachment 79128
    Attachment 79129
    Attachment 79130
    Attachment 79131
    Attachment 79132
    Attachment 79133
    Attachment 79134
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by nuget102; 01-02-2017 at 01:18 PM.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    cipherk98's Avatar
    Join Date
    Jan 2016
    Last On
    @
    Location
    Pennsylvania
    Posts
    278
    Local Date
    03-29-2024
    Local Time
    10:03 AM
    It's a bit hard to tell, but some of that may just be grease in the stock. I'd try to wipe it up and see what happens. My big concern would be getting that action out of the stock to see how bad it is under the wood line. I think the rust looks worse in the pictures than it perhaps is due to it being a mix of rust and dirt and dust suspended in grease but you'll only know for sure once you begin to clean it up and see the pitting underneath. The one spot that sticks out to me as something to really look over is on the front left side of the receiver ring.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    nuget102's Avatar
    Join Date
    Dec 2016
    Last On
    01-26-2020 @ 02:15 PM
    Location
    Kentucky, USA
    Posts
    23
    Local Date
    03-29-2024
    Local Time
    09:03 AM
    Thread Starter
    Quote Originally Posted by cipherk98 View Post
    It's a bit hard to tell, but some of that may just be grease in the stock. I'd try to wipe it up and see what happens. My big concern would be getting that action out of the stock to see how bad it is under the wood line. I think the rust looks worse in the pictures than it perhaps is due to it being a mix of rust and dirt and dust suspended in grease but you'll only know for sure once you begin to clean it up and see the pitting underneath. The one spot that sticks out to me as something to really look over is on the front left side of the receiver ring.
    I took a look and there appears to be a good deal of rust. I'll post pictures soon, but there is some bad pitting... Hopefully it will be visible in the pictures. The pitting is noticeable, but I think the gun is still safe to shoot. The inside of the barrel is good, just the outside is rusted.

  6. #4
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 09:31 AM
    Location
    Victoria BC
    Posts
    29,839
    Real Name
    Jim
    Local Date
    03-29-2024
    Local Time
    07:03 AM
    The spring looks correct from here. I agree about the goop being grease, could be axle grease which isn't even close to the right stuff. I'd put the trigger group together on the rifle and smack it with a nylon hammer. It'll release. The follower could be bent so your rifle doesn't feed, can't see... There's a thread currently about restoring a find like this...worth a look. He's going through what you will be. https://www.milsurps.com/showthread.php?t=59252
    Regards, Jim

  7. #5
    FREE MEMBER
    NO Posting or PM's Allowed
    nuget102's Avatar
    Join Date
    Dec 2016
    Last On
    01-26-2020 @ 02:15 PM
    Location
    Kentucky, USA
    Posts
    23
    Local Date
    03-29-2024
    Local Time
    09:03 AM
    Thread Starter
    Attachment 79143Attachment 79144Attachment 79145Attachment 79146Attachment 79147Attachment 79148Attachment 79149Attachment 79150

    Here's some photos of the gun taken apart. For some reason the stock has holes drilled in it? They're all connected and I think it may be some sort of drain for water perhaps? The barrel isn't drilled or anything.

    Any opinions on the safety of this gun would be appreciated...

  8. #6
    Contributing Member Aragorn243's Avatar
    Join Date
    Apr 2009
    Last On
    Yesterday @ 09:10 PM
    Location
    Pennsylvania, United States
    Posts
    6,974
    Real Name
    Steve
    Local Date
    03-29-2024
    Local Time
    10:03 AM
    Never saw holes drilled like that. they are connected because that is the channel for the cleaning rod. I expect the rifle is fine to shoot. I've seen rust that was a lot worse than that and the stock looks fine also.

  9. #7
    FREE MEMBER
    NO Posting or PM's Allowed
    nuget102's Avatar
    Join Date
    Dec 2016
    Last On
    01-26-2020 @ 02:15 PM
    Location
    Kentucky, USA
    Posts
    23
    Local Date
    03-29-2024
    Local Time
    09:03 AM
    Thread Starter
    Quote Originally Posted by Aragorn243 View Post
    Never saw holes drilled like that. they are connected because that is the channel for the cleaning rod. I expect the rifle is fine to shoot. I've seen rust that was a lot worse than that and the stock looks fine also.
    You can't tell it in the picture, but the stock is actually acting like it's wet... and the inside is mostly crumbling, hopefully it's just on the surface. The stock is incredibly brittle for some reason.

    Also, how's the electrolyte bath working? I read your thread, and it may be what I do. But I'm thinking i'll do a vinegar bath first. Which is really just 1/2 vinegar, 1/2 water and you soak it for a few hours. You need to scrub/wipe the rust off after (depending how long you soak it) and you need to neutralize the vinegar with baking soda/water mixture. But It's easier for me since I have vinegar on hand. Just need a pan to put the barrel in to soak it. I'm currently only soaking the trigger guard. I don't think my gun really NEEDS an electrolyte bath though, it's not as bad as yours was Aragorn :P

  10. #8
    Contributing Member mmppres's Avatar
    Join Date
    Mar 2014
    Last On
    03-22-2024 @ 08:15 AM
    Location
    butler pa
    Age
    58
    Posts
    1,082
    Real Name
    mike
    Local Date
    03-29-2024
    Local Time
    10:03 AM
    Holes were drilled to get cleaning rod out at one time. some one pushed it in to far an then had to drill to find end. saw it one time before on an old Springfield

  11. #9
    FREE MEMBER
    NO Posting or PM's Allowed
    nuget102's Avatar
    Join Date
    Dec 2016
    Last On
    01-26-2020 @ 02:15 PM
    Location
    Kentucky, USA
    Posts
    23
    Local Date
    03-29-2024
    Local Time
    09:03 AM
    Thread Starter
    Quote Originally Posted by mmppres View Post
    Holes were drilled to get cleaning rod out at one time. some one pushed it in to far an then had to drill to find end. saw it one time before on an old Springfield
    Oh, okay. That would makes sense haha. Thanks! As long as it's not a big deal i'm not going to worry about it.

  12. #10
    Contributing Member Aragorn243's Avatar
    Join Date
    Apr 2009
    Last On
    Yesterday @ 09:10 PM
    Location
    Pennsylvania, United States
    Posts
    6,974
    Real Name
    Steve
    Local Date
    03-29-2024
    Local Time
    10:03 AM
    Vinegar will strip the bluing off. I wouldn't recommend it. It also tends to turn deep rust into black rust rather than remove it. I've done it before and if you don't care about the bluing, it does work.

+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. Turkish 8MM Mauser
    By Mike Haas in forum Mauser Rifles
    Replies: 5
    Last Post: 03-07-2015, 08:41 PM
  2. WWI Turkish Mauser
    By Aragorn243 in forum Mauser Rifles
    Replies: 9
    Last Post: 06-04-2012, 12:48 AM
  3. Turkish Mauser???
    By cd202 in forum Mauser Rifles
    Replies: 8
    Last Post: 11-17-2011, 03:44 PM
  4. I broke my 1903 turkish Mauser firing pin
    By labrat1469 in forum Mauser Rifles
    Replies: 6
    Last Post: 10-23-2011, 11:45 PM
  5. My 1903/38 Turkish Mauser
    By labrat1469 in forum Mauser Rifles
    Replies: 3
    Last Post: 10-11-2011, 09:50 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks