+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14

Thread: Rim locking issue.

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member mikedal's Avatar
    Join Date
    Dec 2016
    Last On
    03-13-2023 @ 04:04 AM
    Location
    New Zealand
    Posts
    13
    Local Date
    03-29-2024
    Local Time
    09:18 AM

    Rim locking issue.

    Hi there from down in New Zealandicon.
    My normally reliable and trusty Eddystone P14 has decided to rim lock itself every time a case or unfired round is extracted. Some how the top round ends up with it's rim behind the next one down.
    I haven't changed the way I load the rifle either one at a time or with charger clips and last military shoot it was fine.
    I can't see anything untoward and it is normally fine apart from the odd difficult to feed round which appears to be a brass manufacturer issue.
    Any suggestions would be most appreciated especially since I have a rapid fire military shoot coming up soon.
    Cheers Mike
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by mikedal; 06-18-2017 at 03:27 AM.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Eaglelord17's Avatar
    Join Date
    Aug 2014
    Last On
    Today @ 08:26 AM
    Location
    Sault Ste. Marie, ON
    Posts
    1,257
    Real Name
    A.N.
    Local Date
    03-28-2024
    Local Time
    05:18 PM
    What length do you have the ammo made to and what size bullets are you using? The reason I ask is when I was practicing for a mad minute with the P14, I tried using 129grn bullets (i.e. 7.62x39 bullets) which worked very well for the shooting but would rimlock because it wasn't long enough. With a longer bullet the magazine worked the way it was supposed to and there was no rimlock.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member mikedal's Avatar
    Join Date
    Dec 2016
    Last On
    03-13-2023 @ 04:04 AM
    Location
    New Zealand
    Posts
    13
    Local Date
    03-29-2024
    Local Time
    09:18 AM
    Thread Starter
    Quote Originally Posted by Eaglelord17 View Post
    What length do you have the ammo made to and what size bullets are you using? The reason I ask is when I was practicing for a mad minute with the P14, I tried using 129grn bullets (i.e. 7.62x39 bullets) which worked very well for the shooting but would rimlock because it wasn't long enough. With a longer bullet the magazine worked the way it was supposed to and there was no rimlock.
    Hi
    My loads are 3.05 inchs long (77.5 mm) and I use Hornady 150gr sp interlock projectiles.
    They have been fine in the past which is why I am a bit lost with this problem. I would like to try another mag spring and follower but they don't exactly grow on trees in New Zealandicon.
    Thanks Mike

  6. #4
    Legacy Member mikedal's Avatar
    Join Date
    Dec 2016
    Last On
    03-13-2023 @ 04:04 AM
    Location
    New Zealand
    Posts
    13
    Local Date
    03-29-2024
    Local Time
    09:18 AM
    Thread Starter
    Quote Originally Posted by Eaglelord17 View Post
    What length do you have the ammo made to and what size bullets are you using? The reason I ask is when I was practicing for a mad minute with the P14, I tried using 129grn bullets (i.e. 7.62x39 bullets) which worked very well for the shooting but would rimlock because it wasn't long enough. With a longer bullet the magazine worked the way it was supposed to and there was no rimlock.
    Hi
    My loads are 3.05 inchs long (77.5 mm) and I use Hornady 150gr sp interlock projectiles.
    They have been fine in the past which is why I am a bit lost with this problem. I would like to try another mag spring and follower but they don't exactly grow on trees in New Zealandicon.
    Thanks Mike

  7. #5
    Legacy Member oldfoneguy's Avatar
    Join Date
    Oct 2015
    Last On
    Today @ 04:08 PM
    Location
    long island, ny
    Posts
    561
    Real Name
    Bill
    Local Date
    03-28-2024
    Local Time
    04:18 PM
    My Hornady book lists max COL for .303 Britishicon as 3.035". The books from all my other bullet manufacturers list the max COL at 3.075". I always set my length at 3.075" just to slightly reduce freebore distance. With rifles as old and well used as these it can't hurt to give them a little extra length. Will .025" make a difference most likely not but who knows? I've never run into this problem and am using the spring and follower that came in my P14 which seem to be original to the rifle.

    Just for giggles I decided to measure up some of the 1955 Radway Green ammo I picked up last month and the cartridge lengths run from 3.025 up to 3.068 so that was no help at all. - Bill

  8. #6
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 01:16 PM
    Location
    Victoria BC
    Posts
    29,838
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    02:18 PM
    I've NEVER had this problem, but also never shortened the cartridges up that much. It could well be a case of them moving lengthwise in the magazine box.
    Regards, Jim

  9. #7
    Legacy Member mikedal's Avatar
    Join Date
    Dec 2016
    Last On
    03-13-2023 @ 04:04 AM
    Location
    New Zealand
    Posts
    13
    Local Date
    03-29-2024
    Local Time
    09:18 AM
    Thread Starter
    Progress report.
    I lengthened 5 cartridges to 3.075 inches and this seems to be preventing the rim lock problem although I did have to give the magazine spring a bit of a stretch to lift cartridges up properly for bolt to pick up, mainly only the 2nd round though.
    A great result but strange how it was ok last time I used it with the shorter cartridges I normally use in my SHTLE Enfield. Now I know I guess.
    I haven't long had the P14 and it was in very poor condition when I got it ie so dirty it wouldn't feed at all.
    It is going for a birthday at a military gunsmiths which will hopefully bring it up to much better standard. My biggest problem is finding a set of wood as it has been hacked up by someone who thought they know better. At least they left the barrel alone.

    Thanks for your help everyone and I will let you know how I get on with rebuild.
    Cheers Mike
    Last edited by mikedal; 06-20-2017 at 03:45 AM.

  10. The Following 2 Members Say Thank You to mikedal For This Useful Post:


  11. #8
    Legacy Member 22SqnRAE's Avatar
    Join Date
    Feb 2017
    Last On
    09-27-2023 @ 11:49 PM
    Location
    Brisbane - the middle of right side of Oz
    Posts
    304
    Local Date
    03-29-2024
    Local Time
    07:18 AM
    Mike,

    I've dragged a couple fo No 1 Mk III*s out of the safe after oooh.. aaahhh... eerm... 30 years?

    The mag springs are about as good as half my undies elastics in summer. You've worked out the COL matter, thanks to some fine guidance above, but I do think you've supplied about 60-70% of the solution by dealing with the spring. A strong spring does wonders for rim over in the No 1s, as evidenced by experiment and changes. Found same with No 4 rifles. New spring, no rim lock.

    Well done!
    Trying to save Service history, one rifle at a time...

  12. #9
    Legacy Member mikedal's Avatar
    Join Date
    Dec 2016
    Last On
    03-13-2023 @ 04:04 AM
    Location
    New Zealand
    Posts
    13
    Local Date
    03-29-2024
    Local Time
    09:18 AM
    Thread Starter
    Quote Originally Posted by 22SqnRAE View Post
    Mike,

    I've dragged a couple fo No 1 Mk III*s out of the safe after oooh.. aaahhh... eerm... 30 years?

    The mag springs are about as good as half my undies elastics in summer. You've worked out the COL matter, thanks to some fine guidance above, but I do think you've supplied about 60-70% of the solution by dealing with the spring. A strong spring does wonders for rim over in the No 1s, as evidenced by experiment and changes. Found same with No 4 rifles. New spring, no rim lock.

    Well done!
    Thanks for that. I have a mate bringing me another mag spring up to the range this weekend. That will hopefully make the Mad minute shoot a little less embarrassing. Just got to reconfigure a few box's of ammo now.
    Cheers

  13. #10
    Contributing Member CINDERS's Avatar
    Join Date
    Nov 2009
    Last On
    03-25-2024 @ 11:01 AM
    Location
    South West Western Australia
    Posts
    7,734
    Real Name
    CINDERS
    Local Date
    03-29-2024
    Local Time
    05:18 AM
    Using a kinetic puller or a collet the latter is the way to go I had to do 120 rounds of 303 the other day man that collet puller is miles ahead of the kinetic the powder stays put wish I have brought one years ago.

  14. The Following 2 Members Say Thank You to CINDERS For This Useful Post:


+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. No4 Mk 1* locking Lugs
    By rgallant in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 6
    Last Post: 10-30-2014, 09:16 AM
  2. No32 Mk3 locking rings
    By Merlin266 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 8
    Last Post: 07-03-2014, 03:23 AM
  3. P14 Left Locking Lug
    By rjn in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 2
    Last Post: 04-17-2013, 06:17 AM
  4. Locking Lug Issues
    By vintage hunter in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 2
    Last Post: 03-06-2012, 08:58 PM
  5. p14 Locking Lug size problem
    By Pcahill in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 8
    Last Post: 12-01-2011, 02:26 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks