+ Reply to Thread
Page 2 of 2 FirstFirst 1 2
Results 11 to 16 of 16

Thread: Wood furniture solid wood and laminated date of use

Click here to increase the font size Click here to reduce the font size
  1. #11
    Legacy Member nzl1a1collector's Avatar
    Join Date
    Aug 2008
    Last On
    03-27-2024 @ 02:26 AM
    Location
    New Zealand
    Posts
    621
    Real Name
    Kevin
    Local Date
    03-30-2024
    Local Time
    02:29 AM
    The NZicon pattern carrying handle didn't appear until about 1980, the earliest photo Ive seen is on a rifle in Rhodesia/Zimbabwe where the Kiwis were there for the independence change over.

    How frequently are NZ pattern carrying handles found on Malay contract rifles? its possible they have been fitted when the rifles were imported into the UKicon? a large quantity of ex NZ L1A1 SLRs made it out into the wild, about 7000 were sold to CAI and from there they were turned into parts kits and also sold elsewhere as complete rifles. A lot of NZ rifles had the carrying handles removed by a directive, the carrying handles to be replaced with a neoprene washer.

  2. The Following 2 Members Say Thank You to nzl1a1collector For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #12
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-29-2024
    Local Time
    03:29 PM
    The main problem with wood L1A1 handguards was splitting longitudinally from the front cupped and threaded insert forwards for an inch or so. We had to patch those PDQ otherwise the screw and threaded insert would just rotate and nothing would get it out. for some years during my time in Malaya, a longitudinal split along the top rear along the rear of the gar cylinder could be repaired by roughing up the wood and overlaying that section with a 1" wide 2+" long 3/16" or so thick piece of wood beveled at the edges. It worked well and stood up to the rough treatment they got out in the Far East. But never saw it adopted in the UKicon. Laminated was the best things we had. I seem to recall that the quarter guard who formed up for visiting dignitaries couldn't have the laminated hand guards french polished or varnished because they were treated with some special chemicals. Probably the same stuff that they put into the single blokes tea!

  5. The Following 4 Members Say Thank You to Peter Laidler For This Useful Post:


  6. Avoid Ads - Become a Contributing Member - Click HERE
  7. #13
    Contributing Member mrclark303's Avatar
    Join Date
    Jul 2012
    Last On
    Yesterday @ 11:11 AM
    Location
    The wild west of England
    Posts
    3,401
    Real Name
    Mr Clark
    Local Date
    03-29-2024
    Local Time
    02:29 PM
    Quote Originally Posted by nzl1a1collector View Post
    The NZicon pattern carrying handle didn't appear until about 1980, the earliest photo Ive seen is on a rifle in Rhodesia/Zimbabwe where the Kiwis were there for the independence change over.

    How frequently are NZ pattern carrying handles found on Malay contract rifles? its possible they have been fitted when the rifles were imported into the UKicon? a large quantity of ex NZ L1A1 SLRs made it out into the wild, about 7000 were sold to CAI and from there they were turned into parts kits and also sold elsewhere as complete rifles. A lot of NZ rifles had the carrying handles removed by a directive, the carrying handles to be replaced with a neoprene washer.
    Hi Kev,

    I have seen it on quite a few Rifles, I bought the furniture sets from five ex Malay Rifles that were slated for dismantling, three had NZ spec carry handles plus rather rough two slot handguards.

    I've seen the same NZ handles on ex Malay Rifles in Germanyicon too.

    Why they are on there I don't know. I assumed surplus NZ examples supplied to replace the worn out wooden handles during the final years of Malaysian service.

    They appeared to have been on the Rifles for some years.

    ---------- Post added at 12:26 AM ---------- Previous post was at 12:22 AM ----------

    Probably the same stuff that they put into the single blokes tea!
    .303, helping Englishmen express their feelings since 1889

  8. #14
    Legacy Member nzl1a1collector's Avatar
    Join Date
    Aug 2008
    Last On
    03-27-2024 @ 02:26 AM
    Location
    New Zealand
    Posts
    621
    Real Name
    Kevin
    Local Date
    03-30-2024
    Local Time
    02:29 AM
    That's possible, maybe we sold them some surplus carrying handles after they had them removed and returned to base workshops.?

    Here's some photos showing some of the various handguard repairs


    and the same on the Butts

  9. The Following 3 Members Say Thank You to nzl1a1collector For This Useful Post:


  10. #15
    Contributing Member mrclark303's Avatar
    Join Date
    Jul 2012
    Last On
    Yesterday @ 11:11 AM
    Location
    The wild west of England
    Posts
    3,401
    Real Name
    Mr Clark
    Local Date
    03-29-2024
    Local Time
    02:29 PM
    Thanks for the info kev, I think I have examples of slip patch repaired butts and forends in my spares box. I will have to dig them out.

  11. #16
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    03-24-2024 @ 09:52 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,507
    Real Name
    Peter Laidler
    Local Date
    03-29-2024
    Local Time
    03:29 PM
    We used to repair the front of the hand guards by completely cutting away the front at 60 degrees to half depth and wood patching at 90 degrees to the grain. That seemed OK. But once the threaded insert came loose again - as it would - it was the end of the line. That's a LOT of slip patches in a butt. But if needs must, then that's what you do.

    As apprentices we would patch butts and grips time and time again until the cows came home just for the experience but it was NEVER good enough for Paddy Reilly or Jack Hobbs the class instructors. Some examples of superb work were presented to visiting dignitaries and a brass plate tacked on. But mine work was usually just piled in the corner with the remainder of the 'also rans'

  12. The Following 2 Members Say Thank You to Peter Laidler For This Useful Post:


+ Reply to Thread
Page 2 of 2 FirstFirst 1 2

Similar Threads

  1. Long Branch C/|\ marked "blonde" Maple wood furniture
    By Seaforth72 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 31
    Last Post: 12-09-2016, 03:09 PM
  2. Wood
    By Bruce_in_Oz in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 2
    Last Post: 10-15-2013, 04:55 AM
  3. How to clean wood furniture?
    By Charlie303 in forum FNFAL Rifles
    Replies: 15
    Last Post: 09-09-2013, 04:43 AM
  4. Low Wood or High Wood
    By Bulls-I_24 in forum M1/M2 Carbine
    Replies: 7
    Last Post: 04-28-2010, 11:25 PM
  5. Replacing Wood Furniture on No4 MK2
    By paul_costall in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 6
    Last Post: 07-28-2009, 03:50 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks