+ Reply to Thread
Results 1 to 8 of 8

Thread: Gas Piston Nut depth?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member tlsher's Avatar
    Join Date
    Aug 2012
    Last On
    10-19-2023 @ 11:01 AM
    Location
    Illinois, USA
    Posts
    15
    Local Date
    03-28-2024
    Local Time
    05:17 AM

    Gas Piston Nut depth?

    Hi all!

    I'm new to the M1icon Carbine and just picked up a 5.1M S/N Inland.

    I took it shooting the other day and pushed ~ 40 rounds through it. When I took it apart to clean it, I noticed a couple of things I will need some expert help on.

    First, I noticed that the Gas Piston Nut was working its way out. I have the special wrench and was able to put it back into place, but then I wondered how deep the nut needs to be tightened down. Are there any specs. for depth? Any suggestions on how to "stake" it in place when it's tightened down? Would I even want to stake it down? Looking for advice.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    M1 Garand, Mosin Nagant 91/30, Mosin Nagant M44 Carbine, SMLE No 1 MK III*, Russian SKS, Yugo M59/66A, WASR 10, AR-15, K31 Karabiner, M1 Carbine, Lee Enfield No 4 MkI*, Kar98k, 1911A1, P.08 Luger, P.38

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    03:17 AM
    Tighten it up to tight. You shouldn't have to stake it, you aren't taking it to the Pacific on a campaign.
    Regards, Jim

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member us019255's Avatar
    Join Date
    Mar 2008
    Last On
    Yesterday @ 10:00 AM
    Location
    reluctantly in Santiago, MN
    Age
    81
    Posts
    266
    Real Name
    Ed Hauser
    Local Date
    03-28-2024
    Local Time
    03:17 AM
    The manuals call for it to be staked down. I stake all mine after rebuild. You will never have to remove it unless you rebuild. The hot gas keeps it clean, and (except from some Chinese ammo, which should never ever be used) all ammo is non corrosive.
    Ed reluctantly no longer in the Bitterroot

  6. #4
    Contributing Member W5USMC's Avatar
    Join Date
    Mar 2018
    Last On
    Yesterday @ 11:29 PM
    Location
    Edgar Springs, MO
    Posts
    280
    Real Name
    Wayne
    Local Date
    03-28-2024
    Local Time
    05:17 AM
    You will get mixed thoughts on piston nut staking. I tend to agree with browningautorifleicon on the subject. Yes most manuals call for the nut to be staked however, there is a PS Monthly magazine dated 1961 that states that when the piston nut is securely seated there is no need for the nut to be staked. There is also a suggestion on the CMPicon site under the Carbine shooting with accuracy thread that mentions that some shooters use loc-tite thread locker, of the appropriate color, on the threads to prevent the nut from backing out.

  7. Thank You to W5USMC For This Useful Post:


  8. #5
    Legacy Member Bruce McAskill's Avatar
    Join Date
    Mar 2009
    Last On
    01-17-2023 @ 09:10 PM
    Posts
    1,880
    Local Date
    03-28-2024
    Local Time
    05:17 AM
    DO NOT use too much force with the wrench. The nut should be a good snug fit BUT THAT IS ALL!!!!. If you go too tight and crack the gas housing the barrel is gone and will have to be replaced. Welding does not work to repair a gas housing. It will crack again and every time you try to weld it, it will continue crack again. If it comes loose again then snug it down and stake it in place. Then take that wrench and throw it away. You do not need it to clean a carbine....ever!!!!.

  9. Thank You to Bruce McAskill For This Useful Post:


  10. #6
    Advisory Panel
    painter777's Avatar
    Join Date
    Mar 2009
    Last On
    @
    Location
    Central Michigan
    Posts
    5,312
    Local Date
    03-28-2024
    Local Time
    06:17 AM
    Quote Originally Posted by Bruce McAskill View Post
    If you go too tight and crack the gas housing the barrel is gone and will have to be replaced.
    Very true Bruce,
    It was about this time last year when I threw my back out trying to pull a stubborn barrel off a WRA 1,126,xxx springtube receiver. The last Springtube variation, I believe called variation 3, with NO holes drilled through the right rail.
    Not knowing it was damaged, It was purchased (for too much) at a farm estate auction by a over ambitious friend. A 60's NRA sold carbine.
    After getting it home upon tear down is when I could see the nut was messed up by probably the use of vice grips. I started to straighten out the nut 'Lugs' so I could use the proper wrench, but 1 nut lug was pretty much broken in half. Then seen the gas cylinder had been badly cracked. Like getting punched in the gut. If you recall.. that was the Winchester barrel this friend bent in to a horse show over his knee and threw it in the back of his truck.... off to the dump.
    He told me to sell what I could to try to recoup some of his lost funds. Mention of a replacement barrel didn't interest him, he'd had it with it.
    Later I asked if he'd thrown it away, he gruffly replied it was junk !
    My thought was as long as I let a potential buyer of the receiver know this, that (I wasn't sure) could possibly just hand screw it back on so I could ship to a C&R holder. Of course I would have had to pry it some what straighter so I could box it up. Oh well.... Nice Receiver with IIRC has no sign of ever having a rear adj sight on it or ever refinished.
    I still have the receiver and parts to sell off for him, just haven't got around to it.
    Sorry I'll stop this reads more like a sale add than advice on gas piston nuts.

    I laughed about it later thinking if you had that bent barrel threaded back on it would have looked like one of those Shoot Around The Corner Rifles.....


    Myself I just check them so there are snug. A good case IMO of less is best.
    You crack it or cross thread = not a happy camper

    YMMV,
    Charlie-Painter777

  11. #7
    Legacy Member bonnie's Avatar
    Join Date
    Dec 2008
    Last On
    01-23-2024 @ 04:14 PM
    Posts
    91
    Local Date
    03-28-2024
    Local Time
    05:17 AM
    Recently picked up a rebuilt Inland and found the piston nut not staked and loose. Tighten and staked it. The end. In my early days I removed the nut and piston just because I had to. I don't do that anymore either.

  12. #8
    Legacy Member DaveHH's Avatar
    Join Date
    Mar 2009
    Last On
    03-18-2024 @ 01:37 PM
    Location
    Northern Calif
    Posts
    1,348
    Real Name
    David Haynes
    Local Date
    03-28-2024
    Local Time
    05:17 AM
    There are two reasons to remove the nut and look inside: Curiosity and wanting to clean it. The discovery that it is as clean as a whistle inside is the result of both. Having removed it would I "restake it?" absolutely not. Staking is the physical distortion or wrecking of the threads so they don't work anymore. That is fine when you can turn the carbine into another place and they fix it like new for free. We don't and they won't. So use a gob of permatex or some Loktite and let it go at that.

+ Reply to Thread

Similar Threads

  1. 7.92 chamber depth
    By c310pilot in forum The Bren LMG (Light Machine Gun)
    Replies: 26
    Last Post: 06-04-2015, 01:47 PM
  2. M1C - Gas Piston Nut
    By ppknut in forum M1/M2 Carbine
    Replies: 7
    Last Post: 03-11-2012, 12:10 AM
  3. Gas piston nut, help?
    By Garandrew in forum M1/M2 Carbine
    Replies: 0
    Last Post: 01-01-2011, 08:17 AM
  4. Gas piston nut
    By bearhunter in forum M1/M2 Carbine
    Replies: 0
    Last Post: 11-27-2010, 02:08 AM
  5. Another superb video; depth charge explosion
    By Louis of PA in forum The Watering Hole OT (Off Topic) Forum
    Replies: 0
    Last Post: 03-04-2009, 07:54 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks