+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 30

Thread: 1941 Savage No. 4 Mk 1 Sniper rifle?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Bigwagon's Avatar
    Join Date
    Dec 2016
    Last On
    03-21-2024 @ 10:22 PM
    Location
    WI
    Posts
    40
    Local Date
    03-29-2024
    Local Time
    12:17 AM

    1941 Savage No. 4 Mk 1 Sniper rifle?

    I'd like some opinions and info on this rifle I took a bit of a gamble on at a recent gun show. Hopefully I didn't pay 3x what it's worth! From my basic research it appears to have many correct features and markings of a No.4 T, at least for a Savage. The photos show most of the details, but a few other points to mention.

    SNs match on bolt and magazine
    5-groove barrel with excellent bore
    The forehand was cut off in shorter style with no upper hand guard but a milled band refit
    Buttstock has aluminum buttplate and holes where a cheekrest was mounted
    Micrometer rear sight was butchered into a V-notch (what buffoon thought that was a good idea??)

    I'm most curious about whether this is a legit No. 4 sniper and about the TR and FTR markings. I would like to refit a full fore end and possibly a retro scope and mount as I probably can't afford originals.












    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. Thank You to Bigwagon For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Advisory Panel
    Roger Payne's Avatar
    Join Date
    Mar 2008
    Last On
    03-20-2024 @ 06:05 AM
    Location
    Sutton Coldfield, UK.
    Posts
    3,429
    Real Name
    Roger Payne
    Local Date
    03-29-2024
    Local Time
    05:17 AM
    You can stop worrying, it's real! Well, at least, IMHO it is. As you say, an early Savage rifle, converted to T specs, & having been FTR'ed & wearing a few replacement parts, but a genuine conversion all the same. The FTRing is just a part of its service history. If you need a replacement cursor for your rear sight pm me. I have a plastic ice cream tub full of them somewhere in the garage.......

  5. The Following 3 Members Say Thank You to Roger Payne For This Useful Post:


  6. Avoid Ads - Become a Contributing Member - Click HERE
  7. #3
    Advisory Panel Brian Dick's Avatar
    Join Date
    Apr 2008
    Last On
    Yesterday @ 02:10 PM
    Location
    Edgefield, SC USA
    Posts
    4,040
    Local Date
    03-29-2024
    Local Time
    01:17 AM
    It's certainly legit and well worth restoring properly.

  8. Thank You to Brian Dick For This Useful Post:


  9. #4
    Advisory Panel Surpmil's Avatar
    Join Date
    Feb 2008
    Last On
    @
    Location
    West side
    Posts
    4,651
    Local Date
    03-28-2024
    Local Time
    10:17 PM
    Interesting that the "TR" and "F.T.R" marks appear to have been struck over the finish that presumably went on at the time of the 1945 or later (based on barrel date) FTR.

    The "TR" is not the usual font seen on later rifles, so perhaps one of the not-uncommon retroactive stampings done to early conversions to make them conform to the later markings SOP.

    If both stampings are over and through the FTR refinish, then it seems quite likely they were both done at the same time: as the last steps in the FTR. That is interesting as I don't think we've seen that here before.

    Just about everything but the bolt, and probably the backsight, appears to have been replaced, probably during the FTR, but Peter has told us in the past that common and standard parts were not kept with a particular rifle through FTR.
    “There are invisible rulers who control the destinies of millions. It is not generally realized to what extent the words and actions of our most influential public men are dictated by shrewd persons operating behind the scenes.”

    Edward Bernays, 1928

    Much changes, much remains the same.

  10. The Following 2 Members Say Thank You to Surpmil For This Useful Post:


  11. #5
    Advisory Panel Brian Dick's Avatar
    Join Date
    Apr 2008
    Last On
    Yesterday @ 02:10 PM
    Location
    Edgefield, SC USA
    Posts
    4,040
    Local Date
    03-29-2024
    Local Time
    01:17 AM
    Savage No.4's selected for sniper conversion weren't marked TR as original so it had to be done during FTR. The TR stamp was a selection mark that came into being during production for standard BSA service rifles that shot above average during the range testing. Those rifles so marked were then shipped to Holland and Holland for conversion to No.4T. Very early examples from BSA, Savage, Fazakerley and Maltby up until 1943 seldom have those markings present. At some point in 1943, markings became standardized along with BSA becoming the only supplier of rifles for conversion.

  12. Thank You to Brian Dick For This Useful Post:


  13. #6
    Legacy Member Bigwagon's Avatar
    Join Date
    Dec 2016
    Last On
    03-21-2024 @ 10:22 PM
    Location
    WI
    Posts
    40
    Local Date
    03-29-2024
    Local Time
    12:17 AM
    Thread Starter
    Thanks for the responses. Would I be correct in assuming that even though this rifle is scope-less, it was probably not one of the rifles partially converted without a scope, since it wouldn't have gone through FTR unless it had been issued and used? I will take it to the range tomorrow to see how it performs before how I decide how to proceed. I'd like to pick up a mount at least to put some kind of scope on it along with fixing up the fore-end.

  14. #7
    Advisory Panel
    Roger Payne's Avatar
    Join Date
    Mar 2008
    Last On
    03-20-2024 @ 06:05 AM
    Location
    Sutton Coldfield, UK.
    Posts
    3,429
    Real Name
    Roger Payne
    Local Date
    03-29-2024
    Local Time
    05:17 AM
    Having been made & converted relatively early it is unlikely that it would have been left scopeless. It would probably have had a Mk1 scope, or just possibly an early Mk2 on it.

    I would agree absolutely with Surpmil & Brian. The TR & FTR were applied after the black paint & were probably applied, at least in the case of the TR, to bring it up to the accepted 'standard'. The TR & FTR are in fonts that I have seen on a number of early conversions (both Trials rifles & early run of production rifles), that have been through the FTR process perhaps late in WW2 or immediately afterwards, before the standard pantographed FTR markings became the norm.

    P.S. I was just looking at smleaddict's post about his Maltby 4T - if you look at the FTR & TR stamps on the butt socket of his rifle I reckon they're pretty similar to those on the Savage. They might even be the same font, although I'd hesitate to go that far as the markings on the Maltby are not very well applied, with parts of most of the letters missing. Note that both of these rifles are (presumably) early conversions of early rifles that got early FTR's!
    Last edited by Roger Payne; 06-02-2018 at 08:05 PM.

  15. The Following 2 Members Say Thank You to Roger Payne For This Useful Post:


  16. #8
    Legacy Member Bigwagon's Avatar
    Join Date
    Dec 2016
    Last On
    03-21-2024 @ 10:22 PM
    Location
    WI
    Posts
    40
    Local Date
    03-29-2024
    Local Time
    12:17 AM
    Thread Starter
    Took it to the range today to sight in and function check. Function was fine but sighting in at 50 yards with the irons and PPU ammo took some time. It was shooting way to the left and to get it centered up I had to move the front blade almost all the way to the left side of the dovetail block. With the butchered rear sight aperture it was difficult to get good vertical alignment and the grouping showed that. Horizontal dispersion looks like it will be capable of 1-2 MOA (the six shots along the left were adjusting elevation up; the 5 shots farthest to the right in the bull were my last. I made another front sight adjustment but was out of ammo). Since the sight is already ruined I might drill and tap it for a removable aperture and see if that helps. Bedding with the cutoff stock may be part of the problem too.

    Last edited by Bigwagon; 06-03-2018 at 03:31 PM.

  17. #9
    Legacy Member Strangely Brown's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:06 AM
    Location
    Wiltshire UK
    Age
    72
    Posts
    551
    Real Name
    Mick Kelly
    Local Date
    03-29-2024
    Local Time
    05:17 AM
    Answered my own question by re reading the original post!
    Last edited by Strangely Brown; 06-03-2018 at 04:25 PM.
    Mick

  18. #10
    Advisory Panel
    Roger Payne's Avatar
    Join Date
    Mar 2008
    Last On
    03-20-2024 @ 06:05 AM
    Location
    Sutton Coldfield, UK.
    Posts
    3,429
    Real Name
    Roger Payne
    Local Date
    03-29-2024
    Local Time
    05:17 AM
    Bigwagon, if you want a replacement cursor for the knackered one on your existing rear sight, I'll give you one. Just drop me a pm. It does mean though, that you'll have to take the sight apart to remove the old one & put on the new. There are plenty of people on this forum who can talk you through that, if you need any advice. It's not really complicated, just a bit fiddley.

  19. Thank You to Roger Payne For This Useful Post:


+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. USMC M-1941 sniper Unertl Sniper rifle
    By Boom-Boom in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 2
    Last Post: 11-08-2010, 11:15 AM
  2. 1942 No.4 Mk1*(T) Savage Sniper Rifle (less scope)
    By Badger in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 4
    Last Post: 07-13-2008, 02:46 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks