+ Reply to Thread
Results 1 to 4 of 4

Thread: Scale/check weight issue...

Click here to increase the font size Click here to reduce the font size
  1. #1
    Senior Member amadeus76's Avatar
    Join Date
    Dec 2016
    Last On
    Yesterday @ 10:21 PM
    Location
    Harker Heights, tx
    Posts
    194
    Local Date
    07-16-2018
    Local Time
    11:14 PM

    Scale/check weight issue...

    So I have a RCBS M500 mechanical scale. I also have a set of RCBS check weights. When I adjust the scale and set it at zero and check it against the check weights it never comes out right. Now usually I go by my chargemaster and check it against a smaller electronic scale when needed (they're usually within .1 of each other) and against the M500 if I feel really unsure, but the scale looks to be farther off. This has yet to be a safety concern as I tend to use powder charges under the maximum pressure. But for safety's sake if I do start using higher pressure charges, should I trust the scale or the check weights?

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    No Drill-Tap scope mounts for Mosin Nagant, Mauser K98K, Yugo M48, Swedish M96 and M38, Swiss K31, K11, 1911 and more! Bringing mil-surplus rifles to modern standard without damaging historical values! LIMITED TIME OFFER FROM THE AMERICAN GUNSMITHING INSTITUTE: Get Immediate Online Access To AGI's NEW Armorer's Course for Glock Pistols, Covering Every Generation of Glocks, Including the Latest Model 42/43 and Double Stack Pistols for ONLY $7.00! Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Chuck in Denver ... Buy-Sell-Trade .. Guns, Cars Motorcycles Service Publications - Collectors books that earn their place in your library! Your source for the finest in High Power Competition Gear. Canadian Import and Export Services (Click banner ad for more information) Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Contributing Member Mr E's Avatar
    Join Date
    Feb 2012
    Last On
    Yesterday @ 08:43 PM
    Location
    Flippin Arky
    Posts
    363
    Local Date
    07-16-2018
    Local Time
    11:14 PM
    See if you have some grit in the pivot point on the scale. I did on my scale one time and it made the scale unreliable so I got another set of scales. when I was packing up the old scales I found the piece of grit so I cleaned the scales and tested them again and they were right on
    1ATSR 177AD & 4/3 RNSWR

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Really Senior Member us019255's Avatar
    Join Date
    Mar 2008
    Last On
    Yesterday @ 10:02 AM
    Location
    reluctantly in Santiago, MN
    Age
    76
    Posts
    241
    Local Date
    07-16-2018
    Local Time
    09:14 PM
    0.1 grain is about 6 milligrams. If your check weight is a commercial 20 gram weight like mine, it should be within .1 milligram of actual mass. I would trust the check weights not any mechanical powder scale or electronic one. In the good old days when I took analytical chemistry, which was before electronic analytical balances, our mechanical balances were in special conditioned rooms, on concrete benches attached to a concrete wall that went down to the ground. The other way to do it was to put the balance on a rock or concrete slab that sat on a half inflated inner tube. We also calibrated each weight against a standard verified by the bureau of standards.

    We did this because we needed to be within 0.1 milligrams of actual weight. That is equivalent to 0.0015 grains. My bottom line is that weighing to .1 grain is not all that hard. Just be careful about big drafts, and passing trucks and you will be fine.
    Ed reluctantly no longer in the Bitterroot

  6. Thank You to us019255 For This Useful Post:


  7. #4
    Really Senior Member Sunray's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 02:03 PM
    Location
    London, Ontario
    Posts
    492
    Local Date
    07-17-2018
    Local Time
    12:14 AM
    "...within .1 of each other..." .1 of what? Ounces? Grams? Grains? 1 grain = 1/7000 of a pound. 1/10 of 1 grain is infinitesimally small.
    Personally, if I had an electronic scale I'd be retiring the balance scale. However, what you sit the RCBS scale on matters a bit too. If it's not flat that can throw it off a little. Never had any kind of check weights myself in 40 some years of reloading. Don't over complicate the whole thing.

    Spelling and Grammar count!

  8. Thank You to Sunray For This Useful Post:


+ Reply to Thread

Similar Threads

  1. A simple trigger lightening fix and weight check
    By Von Gruff in forum Martini Henry Rifles
    Replies: 2
    Last Post: 04-19-2017, 02:34 AM
  2. P14 scale drawing - SAID series
    By ssj in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 5
    Last Post: 08-06-2014, 05:58 PM
  3. No.4(T) pewter 1/4 scale model
    By Nigel in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 20
    Last Post: 04-22-2014, 02:47 PM
  4. 1:4 scale M16 Rifle Available?
    By bgilmore in forum M16A2/AR15A2 Rifles
    Replies: 0
    Last Post: 10-13-2009, 05:50 PM
  5. electric/digital scale
    By biggles in forum Ammunition and Reloading for Old Milsurps
    Replies: 6
    Last Post: 10-03-2009, 09:31 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts