+ Reply to Thread
Results 1 to 10 of 10

Thread: 7.55 Swiss vs K31 Die sets?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member amadeus76's Avatar
    Join Date
    Dec 2016
    Last On
    01-11-2024 @ 06:51 PM
    Location
    Harker Heights, tx
    Posts
    305
    Local Date
    03-28-2024
    Local Time
    09:32 AM

    7.55 Swiss vs K31 Die sets?

    So I have both a Swissicon 1911 long rifle and a K31. Obviously both of these are chambered for 7.55 Swiss. And as I do for all my other calibers I would prefer to reload for them. I've done some initial looking around and have noticed that there are dies listed specifically for both, often by the same maker. So my question is, is there a real reason for this or is it a marketing thing? Can I get away with only buying one and if so, is one (K31 vs 7.55 Swiss) preferable?

    Thanks.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Sunray's Avatar
    Join Date
    Mar 2009
    Last On
    03-29-2021 @ 03:01 PM
    Location
    London, Ontario
    Posts
    1,053
    Local Date
    03-28-2024
    Local Time
    10:32 AM
    Everything you ever wanted to know about the rifles and their ammo is here. There are very few sites that are as comprehensive as Swissicon Rifles. Reloading for 'em, including good pictures of the assorted 7.5 Swiss cartridges, is under Ammunition. They say(FAQ's) it's safe to fire modern 7.5x55 rounds in 1896/11s, 1911s and K31s. You'd have to work up a load for both rifles though.
    SwissRifles
    Spelling and Grammar count!

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Contributing Member Ovidio's Avatar
    Join Date
    Dec 2016
    Last On
    03-26-2024 @ 05:58 PM
    Location
    Pordenone, Italy
    Posts
    2,141
    Real Name
    Ovidio Gentiloni
    Local Date
    03-28-2024
    Local Time
    03:32 PM
    I reload with the Lee dies for 7,5x55 Swissicon, FL set for collet only. For my K31.
    No issues at all.
    34a cp., btg. Susa, 3° rgt. Alpini

  6. #4
    Advisory Panel Parashooter's Avatar
    Join Date
    Dec 2008
    Last On
    Today @ 02:24 AM
    Location
    Connecticut
    Age
    79
    Posts
    677
    Local Date
    03-28-2024
    Local Time
    10:32 AM
    K31icon and 1911 chambers differ in body taper (and throat length). Dies made specifically for K31 will not FL size cases to fit smaller 1911 chamber. Standard (1911) dies work for both.


  7. The Following 2 Members Say Thank You to Parashooter For This Useful Post:


  8. #5
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    04:32 PM
    Parashooter's post illustrates a basic rule for all milsurps: even if the rifles have the same nominal caliber, use only neck-sizing dies AND keep the cases separate for each rifle.
    I find that a simple and reliable way to do this is to use cases from different manufacturers for different rifles.

    This prevents the annoyance of getting to the range with the rifle that has the tighter chamber, and finding you have brought the ammo for the rifle with the looser chamber!

    You can, of course, always full-size for the minimum chamber, but case life will be short.
    Last edited by Patrick Chadwick; 07-04-2018 at 10:24 AM.

  9. #6
    Legacy Member bob q's Avatar
    Join Date
    Sep 2014
    Last On
    03-20-2024 @ 10:15 PM
    Location
    north texas
    Posts
    444
    Local Date
    03-28-2024
    Local Time
    09:32 AM
    [QUOTE=Patrick Chadwick;433851]Parashooter's post illustrates a basic rule for all milsurps: [I]even if the rifles have the same nominal caliber, use only neck

    What do you do if you have 300 to 500 rifles in the same caliber ?

  10. #7
    Advisory Panel Parashooter's Avatar
    Join Date
    Dec 2008
    Last On
    Today @ 02:24 AM
    Location
    Connecticut
    Age
    79
    Posts
    677
    Local Date
    03-28-2024
    Local Time
    10:32 AM
    Unfortunately, neck sizing doesn't work very well for these straight-pulls unless significantly reduced loads are used. At full pressure, cases are often expanded enough that they cannot be easily chambered and extracted via a mechanizm where the bolt's turning force is applied indirectly through a cam arrangement that converts axial to radial motion. This is very different from the usual turnbolt action where all we have to do with a tight case is crank a bit more forcefully on the big handle.

    7.5x55 cases that have been fired will full loads should be FL sized to avoid disappointment at the range. At the very least, sized cases should should checked in the rifle for easy chambering and extraction - before charging. Those wishing to enhance case life can learn to adjust FL sizers to produce minimal cartridge end-play while maintaining an easy fit.

  11. Thank You to Parashooter For This Useful Post:


  12. #8
    Legacy Member Eaglelord17's Avatar
    Join Date
    Aug 2014
    Last On
    Today @ 08:26 AM
    Location
    Sault Ste. Marie, ON
    Posts
    1,257
    Real Name
    A.N.
    Local Date
    03-28-2024
    Local Time
    10:32 AM
    My buddy used to reload for the K31icon. It was a absolute nightmare for him. Everything needed to be tight tolerances to get it to function reliably. Everytime he reloaded he had to trim the cases.

    In comparison my for my I.G. 1889 I have never trimmed the cases (though I am going to have to now as I found I couldn't chamber rounds that would fit in the 1889 in my K1893). I could also get away with much more slop in the reloading, whereas he had to spend a lot of time making sure it was all 100% on point.

  13. #9
    Contributing Member Ovidio's Avatar
    Join Date
    Dec 2016
    Last On
    03-26-2024 @ 05:58 PM
    Location
    Pordenone, Italy
    Posts
    2,141
    Real Name
    Ovidio Gentiloni
    Local Date
    03-28-2024
    Local Time
    03:32 PM
    I'm not having all those trouble with my K31icon. I only neck-size, so they are a bit tight when chambering, but really just a tad. I sometimes have to push the handle harder or rap it with the palm just a bit.
    My current brass has gone through 4 reloads and I have not trimmed it yet, although it is on my to-do list after tomorrows "session".
    34a cp., btg. Susa, 3° rgt. Alpini

  14. #10
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Today @ 04:54 AM
    Location
    Brisbane
    Posts
    2,237
    Local Date
    03-29-2024
    Local Time
    12:32 AM
    In barrel production, chamber reamers start out "oversized, (actually at the MAX end of the design tolerance) and, as they wear, are sharpened and re-ground to maintain the acceptable tolerances.

    The first chamber cut with a brand-new reamer will be "bigger" than one cut with one on its last legs, however, BOTH will be within "spec". At the point where the reamer can no longer meet gauging after a re-grind / sharpening, it will be scrapped and a new one put into operation.

    SERVICE ammo MUST fit ALL SERVICE chambers, ALL the time. Generally, service brass is fired in a service chamber ONCE and once only. I recall that the Swedes reloaded some of their 6.5 x 55 brass, on a one-time basis and strictly for use as training ammo. Anyone know if the Swissicon did the same? Before lead-based priming compounds, it was a definite non-starter as a practice.

    If you think Swiss chambers and brass are "funny", try reloading for all-original Japaneseicon 6.5mm and 7.7mm rifles with original factory-cut chambers; "benchrest-grade" chambers they are NOT.

    With two or three different rifles of the same nominal calibre, you may get better groups and case life from careful separation and "custom" loadings. If you are feeding a battalion's worth of rifles of the same calibre, the only sane choice is to load all the ammo the same, zero the rifles accordingly and stop worrying. When a case fails after sundry annealings, resizings and trimmings, consign it to the recycle bucket and enjoy the shooting.

  15. Thank You to Bruce_in_Oz For This Useful Post:


+ Reply to Thread

Similar Threads

  1. Swiss Military and Swiss Reproduction Bags
    By Mil-Spec in forum Swiss Rifles
    Replies: 6
    Last Post: 04-04-2016, 04:49 PM
  2. Swiss Military and Swiss Reproduction Bags
    By Mil-Spec in forum Milsurps General Discussion Forum
    Replies: 2
    Last Post: 03-22-2016, 11:22 AM
  3. Web Gear Sets
    By Harlan (Deceased) in forum Vintage Military Gear
    Replies: 8
    Last Post: 11-27-2011, 12:28 AM
  4. AIM Surplus has No. 4 MK I stock sets
    By kscchtrainer in forum The Restorer's Corner
    Replies: 11
    Last Post: 08-23-2008, 11:10 PM
  5. AIM Surplus has No. 4 MK I stock sets
    By kscchtrainer in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 11
    Last Post: 08-23-2008, 11:10 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks