+ Reply to Thread
Results 1 to 5 of 5

Thread: Restoration of a Martini Henry - inletting fun

Click here to increase the font size Click here to reduce the font size
  1. #1
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-29-2024
    Local Time
    08:42 AM

    Restoration of a Martini Henry - inletting fun

    Hi folks, thought I'd share this one with you, simply given the fun I had inletting the forend to receive the metal tab (or "hook").

    The India-made forend came rather "naked" - it required inletting both for that hook, and for the semi-hexagonal shape of the barrel at the knox.

    I started by drilling the two screw holes on the new forend, to make sure I was going to draw out the profile of the metal hook in the right spot.




    i screwed the hook upside down to get a flat contact with the forend, to mark the contour.



    I figured that doing all the inletting by hand was going to be time consuming and, given my hand carving skills, the result would probably end up unsatisfactory. What I needed was a milling machine. But, have you seen the prices on such tools?

    Cheap as I am, I started looking for alternatives. I do have a drill press, so... I found out that small milling "tables" exist. Some $120 later, I was set for some milling on that forend. I went for the "Proxxon micro compound table". I'Ve screwed it on a rectangular piece of plywood, and clamped that plywood in my drill press vise. I used a small, round router bit
    for the inletting.

    In this picture I had just started. The clamping of the forend is a rather... "homemade" affair but, it worked. Almost.



    After I started the forend began creeping upwards. So I made a simple cross-member between two of the screws. You can see it in the following picture.



    After that, final inletting was done with chisels. I'm pretty sure I saved some time, and it was fun too.



    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. The Following 3 Members Say Thank You to louthepou For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Age
    2010
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-29-2024
    Local Time
    03:42 PM
    Good work Lou! And now that you've made the investment in the milling table, you will have to tackle a few more projects!

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-29-2024
    Local Time
    08:42 AM
    Thread Starter
    i'm afraid of what's going to find its way into my shop now...

    A few more pics, almost done. Missing a front band, and a screw to install the small cap at the tip of the muzzle. The grain of the wood is decent (even with the knot in the buttstock). This is typical made-in-India stuff, and it was covered with dark brown stain. Looks much better after being stripped and refinish with linseed oilicon in my opinion.

    the action was rather... full of crud...


    All cleaned and reassembled now.





    Lou

  7. The Following 2 Members Say Thank You to louthepou For This Useful Post:


  8. #4
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-29-2024
    Local Time
    03:42 PM
    Quote Originally Posted by louthepou View Post
    The grain of the wood is decent (even with the knot in the buttstock).
    Actually, as knots go, that is a splendid example, with the grain swirling round the knot like a galaxy round its core. Polish it carefully and make it a real feature - to be displayed, not hidden!

    After all, what is burr walnut but a highly decorative form of "knottiness"?
    Last edited by Patrick Chadwick; 09-03-2018 at 10:20 AM.

  9. #5
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-29-2024
    Local Time
    08:42 AM
    Thread Starter
    It's the eye of Sauron from Lord of the Rings! lol

    I does look great. Gives it character, sets it apart from other Martinis in a crowd for sure. Sadly, it's not mine!!!

+ Reply to Thread

Similar Threads

  1. martini henry MK IV
    By enfield n2 mk1 in forum Martini Henry Rifles
    Replies: 11
    Last Post: 11-05-2017, 09:11 AM
  2. Martini Henry Mk I
    By boltaction in forum Martini Henry Rifles
    Replies: 6
    Last Post: 10-10-2016, 06:41 PM
  3. New Martini Henry MK IV
    By Aragorn243 in forum Martini Henry Rifles
    Replies: 17
    Last Post: 02-05-2016, 09:34 PM
  4. Martini-Henry in .303?
    By csm102d in forum Martini Henry Rifles
    Replies: 7
    Last Post: 08-12-2012, 04:20 PM
  5. Best Martini Henry
    By MIL rifle1 in forum Martini Henry Rifles
    Replies: 12
    Last Post: 03-08-2010, 05:14 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks