+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 16

Thread: Is this possibly a head space issue?

Click here to increase the font size Click here to reduce the font size
  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    Jaxson50's Avatar
    Join Date
    Aug 2018
    Last On
    01-29-2020 @ 12:35 PM
    Location
    Idaho
    Posts
    50
    Local Date
    03-28-2024
    Local Time
    05:04 PM

    Is this possibly a head space issue?

    I took my recently acquired US Model 1917 to the range last week, shooting commercial 180 gr. loads the recoil was pronounced enough that the range master commented on it.
    After about 12 rounds it became difficult to pull the bolt back, it rotated well, but after three more rounds it wouldn’t pull back at all. The range master used a rubber mallet to tap it open.
    I was slow firing so I don’t believe it was a heat issue. The shells extracted correctly.
    I inspected the primers and it did seem they had rounded off, in other words the fired primers were no longer flat but rounded a bit.
    After returning home I cleaned it well, the bolt cycles well now, but there was a considerable amount of black caked of goop in the action where the bolt lugs rotate.
    To be clear, I have fired more than a few .30 caliber and larger rifles, I’m not a stranger to recoil, my standard range rifle is a M1Aicon.
    The recoil was more what I would expect from a 45 70.
    Does this sound like a head space issue?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by Jaxson50; 10-16-2018 at 10:20 PM.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-29-2024
    Local Time
    02:04 AM

    Is it still a 30-06?

    Quote Originally Posted by Jaxson50 View Post
    After returning home I cleaned it well, the bolt cycles well now, but there was a considerable amount of black caked of goop in the action where the bolt lugs rotate.
    My guess: the only place that "black goop" material can come from is from the cartridge case itself, in the form of incompletely burnt powder.

    Since the case neck normally obturates to seal against the chamber, one has the nasty suspicion that this is precisely what is not happening.

    This effect may appear with underloaded ammo that does not provide enough "bang" to expand the neck sufficiently. But you say that you used commercial ammo, so we are left with the worrying possibility that the neck area of the chamber is too large. In which case, the barrel is kaputt, KO, scrap, whatever you like to call it, but NBG for shooting.

    When you bought the rifle, was it specifically sold as being chambered in 30-06? In the past, some very peculiar things have happened, such as old 30-06s being reamed out to take 8mm Mauser or wildcat chamberings.

    A chamber cast seems to be advisable here. Maybe the rifle is no longer chambered in 30-06.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Contributing Member mmppres's Avatar
    Join Date
    Mar 2014
    Last On
    03-22-2024 @ 08:15 AM
    Location
    butler pa
    Age
    58
    Posts
    1,082
    Real Name
    mike
    Local Date
    03-28-2024
    Local Time
    08:04 PM
    I am also in the mind set that you need to get a chamber case done. Were there any other sign on the fired cases. Rings splits etc?

  6. #4
    Contributing Member rcathey's Avatar
    Join Date
    Dec 2012
    Last On
    Yesterday @ 11:56 AM
    Location
    St. Louis, MO Area
    Posts
    1,645
    Local Date
    03-28-2024
    Local Time
    07:04 PM
    Did you clean any oil/grease out of the chamber that may have been present? A lubricated chamber would increase bolt thrust.

  7. #5
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-29-2024
    Local Time
    02:04 AM
    Before making a chamber casting, the simplest thing to do would be to measure a fired case, and compare the results with the SAAMI or CIP standards. A chamber casting can be very problematical if the chamber has a ring (from overpressure or scoured-out rust) as it is then very difficult or even impossible to extract the casting !

    A properly obturated case will be a couple of thousandths smaller than the SAAMI/CIP chamber dimensions, but never larger. If, for instance, the neck on a fired case is wider than the maximum chamber dimension, then the chamber is no longer correct for 30-06.
    Last edited by Patrick Chadwick; 10-17-2018 at 10:19 AM.

  8. The Following 2 Members Say Thank You to Patrick Chadwick For This Useful Post:


  9. #6
    Legacy Member us019255's Avatar
    Join Date
    Mar 2008
    Last On
    Today @ 09:58 AM
    Location
    reluctantly in Santiago, MN
    Age
    81
    Posts
    266
    Real Name
    Ed Hauser
    Local Date
    03-28-2024
    Local Time
    05:04 PM
    Quote Originally Posted by Patrick Chadwick View Post
    Before making a chamber casting, the simplest thing to do would be to measure a fired case,
    I like that advice. I never thought of that, even though I was suspecting a chamber problem. I learn a lot from this forum! I hope Jaxon50 finds out what is going on.
    Ed reluctantly no longer in the Bitterroot

  10. #7
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 01:16 PM
    Location
    Victoria BC
    Posts
    29,838
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    05:04 PM
    Quote Originally Posted by Patrick Chadwick View Post
    measure a fired case
    How about a picture of one here? It should be obvious...if there's something amiss.
    Regards, Jim

  11. #8
    FREE MEMBER
    NO Posting or PM's Allowed
    Jaxson50's Avatar
    Join Date
    Aug 2018
    Last On
    01-29-2020 @ 12:35 PM
    Location
    Idaho
    Posts
    50
    Local Date
    03-28-2024
    Local Time
    05:04 PM
    Thread Starter
    Thanks for the suggestions, I will follow up on them asap, and post what I learn here.
    A couple of notes, the barrel is original, date stamps indicate Sept. 1918. The serial number indicates the receiver was made in October 1918.
    Before firing I cleaned the bore and chamber.
    The problem wasn't that the brass was stuck, it was the bolt itself. It rotated fine, but wouldn't draw back. As soon as it was tapped it would draw back and the brass extracted without any problems.
    I was shooting Federal Power Shock 180 grain bullets. I saved all the brass, looking at them now I see very minor scratches on a few, the finish is bright from the rim up about 1/4 inch, then they aren't dull. I can find not signs of cracking, splitting or excessive widening of the throat.
    The unfired primers aren't rounded a bit, but the primers on the fired brass are flat, like they were flattened against the bolt face.

  12. #9
    Legacy Member Ridolpho's Avatar
    Join Date
    Jan 2012
    Last On
    09-27-2022 @ 11:12 PM
    Location
    Province of Alberta, Canada
    Age
    66
    Posts
    1,019
    Local Date
    03-28-2024
    Local Time
    06:04 PM
    Jaxson50: You didn't say anything about the general condition of the gun. How does a bullet seem to fit at the muzzle? Have someone shine a light from the muzzle and try to eyeball the chamber area from the rear- is it clean and rust free? Was the gun completely cleaned of any storage grease crappola- I'm always amazed at how much of this stuff I find in the locking shoulder/ extractor cutout area of some rifles that I know have been shot by previous owners. What you describe almost sounds like more gunk than a few rounds of quality ammo can generate from gas leakage. As BAR suggests- try to post some photos.


    Ridolpho

  13. #10
    FREE MEMBER
    NO Posting or PM's Allowed
    Jaxson50's Avatar
    Join Date
    Aug 2018
    Last On
    01-29-2020 @ 12:35 PM
    Location
    Idaho
    Posts
    50
    Local Date
    03-28-2024
    Local Time
    05:04 PM
    Thread Starter
    Sorry I haven't posted pics. I have tried but had problems as I'm using a tablet I guess.
    I did cover a bullet with a magic marker ink and cycled the shell, it left two light impressions from lands on the bullet half water between the tip and the shoulder of the bullet.
    The weapon itself is in excellent condition, certainly worth fixing.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. IHC Head Space Issue?
    By SpikeDD in forum M1 Garand/M14/M1A Rifles
    Replies: 6
    Last Post: 05-17-2015, 10:31 PM
  2. Insufficient Head Space?
    By 101VooDoo in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 10
    Last Post: 01-31-2011, 02:00 AM
  3. garand head space
    By DaveN in forum M1 Garand/M14/M1A Rifles
    Replies: 4
    Last Post: 03-09-2010, 03:46 PM
  4. Checking Head Space
    By miketuite in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 4
    Last Post: 01-16-2010, 11:18 PM
  5. measuring head space
    By RJW NZ in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 8
    Last Post: 09-23-2009, 08:46 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks