+ Reply to Thread
Results 1 to 3 of 3

Thread: Stocking up P14

Click here to increase the font size Click here to reduce the font size
  1. #1
    Really Senior Member nijalninja's Avatar
    Join Date
    Nov 2017
    Last On
    Today @ 05:17 PM
    Location
    Australia
    Age
    20
    Posts
    353
    Local Date
    02-17-2019
    Local Time
    07:19 AM

    Stocking up P14

    G'day there, I have a rifle I am restoring at the moment which had a lot of cracks in the fore-end (Tang crack, behind the mag, etc), but I have repaired all of that as good as I can.

    One which I am curious about is that the wooden block that is acted on by the recoil block on the action was totally sheared out of the stock. I cut-out and refit it as best I could but I am now wondering how it is meant to bear on the action block so that this cannot happen again. Is it meant to be quite tight, like the draws of a Lee-Enfield? If so I can just carve out the front of it, fit a hardwood block, and then fit the action. Just don't want to dive in and make an idiot of myself.

    Also, how are the action screws and there collars meant to bear with the action? Such that the collars are bottoming out at the same time the action and stock bottom out like the main screw on an SMLE/No4/etc?

    Is the barrel meant to be bedded with the stock as well? Just things that I know about Lee-Enfields but know basically nothing with this rifle. Damn mauser looking thing.

    Anyway, I appreciate any help to get the stock fitted the right way. I also have pictures of the whole mess if people want to see it. Cheers.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Age
    2010
    Posts
    All Threads
    No Drill-Tap scope mounts for Mosin Nagant, Mauser K98K, Yugo M48, Swedish M96 and M38, Swiss K31, K11, 1911 and more! Bringing mil-surplus rifles to modern standard without damaging historical values! We specialise in military utensils and artefacts such as helmets, daggers, medals and badges, etc.  The on-line store is intended for personal browsing and searching of collecting objects. All items are provided historical value only and can be used for home collection or other purposes except of fascism, Nazism or other extremism manifestation or its propaganda. LIMITED TIME OFFER FROM THE AMERICAN GUNSMITHING INSTITUTE: Get Immediate Online Access To AGI's NEW Armorer's Course for Glock Pistols, Covering Every Generation of Glocks, Including the Latest Model 42/43 and Double Stack Pistols for ONLY $7.00! Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Chuck in Denver ... Buy-Sell-Trade .. Guns, Cars Motorcycles We pride ourselves on being the new lowest price listing service, and the simplest to use. If you need to buy or sell collectible firearms or any firearm in your legal possession, then this is the place for you. If you’re a big collector clearing house, or other seller that could benefit from a Premium seller account, then we can also support you here at Gunonline.com. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Member gc1054's Avatar
    Join Date
    Jul 2012
    Last On
    Yesterday @ 04:44 PM
    Location
    Central PA USA
    Posts
    55
    Local Date
    02-16-2019
    Local Time
    04:19 PM
    Quite a bit of work required to get this stock ready for shooting! Some thoughts below:

    -The receiver recoil lug should be against the face of the recoil block in the stock when the trigger guard screws and stock bushings are installed and just snugged.
    -The stock bushings are installed such that there is a small amount of wood compression when the front and rear trigger guard screws are snugged up (similar to a No4 rifle front trigger guard bushing setup).
    -When the front and rear screws are tightened up (but not gorilla tight) there should be >2lbs required to lift the barrel off the forend barrel bed (barrel is pressure bedded at muzzle end). The actual weight can vary a bit but the range of 2-7lbs (similar to a No 4 rifle) usually works ok to start off. When tightening the screws do the front one first then the rear tang screw.
    -The rear tang screw can be adjusted a bit to help set the barrel pressure (tighter normally equals less pressure. If there is no barrel pressure and the stock is heavily compressed under the tang a shim may be required under the tang to tip the action slightly down in the stock to reestablish barrel pressure at the stock tip. Of course other bedding areas may affect (for example the height of the replacement recoil block just installed) this so check the usual suspects prior to inserting tang shims.

    There's lots of info on the forum about stocking up this type of action (1917, 1903, Mauser 98s, etc.)

  4. Thank You to gc1054 For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Really Senior Member nijalninja's Avatar
    Join Date
    Nov 2017
    Last On
    Today @ 05:17 PM
    Location
    Australia
    Age
    20
    Posts
    353
    Local Date
    02-17-2019
    Local Time
    07:19 AM
    Thread Starter
    Thanks mate, that is pretty much all the answers I was after. Cheers.


+ Reply to Thread

Similar Threads

  1. Stocking a no4 mk2 for target shooting 300, 500 and 600m
    By ssj in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 8
    Last Post: 07-03-2013, 08:22 PM
  2. Stocking up a P14
    By Ridolpho in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 2
    Last Post: 05-09-2013, 10:51 AM
  3. Stocking up Grease
    By Jugs in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 21
    Last Post: 11-04-2012, 10:05 AM
  4. Garand Christmas Stocking....
    By Amsdorf in forum M1 Garand/M14/M1A Rifles
    Replies: 0
    Last Post: 12-18-2011, 12:03 PM
  5. Question on stocking up
    By newcastle in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 5
    Last Post: 07-31-2011, 06:27 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts