+ Reply to Thread
Results 1 to 8 of 8

Thread: Lee Enfield Sling Swivel Screw

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member DanL96a1's Avatar
    Join Date
    Mar 2009
    Last On
    02-19-2024 @ 04:35 AM
    Age
    41
    Posts
    188
    Local Date
    03-29-2024
    Local Time
    06:36 AM

    Lee Enfield Sling Swivel Screw

    I have had mixed advice on the main sling screw (in front of magazine) being done up tight when not in use or storage. Do you leave Lee Enfield screws done up tight when not in use or leave them tight?

    I would assume it could cause the wood to crack, if left under constant contact/ stress?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Age
    2010
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Alan de Enfield's Avatar
    Join Date
    Nov 2007
    Last On
    Yesterday @ 12:25 PM
    Location
    Y Felinheli, Gogledd Cymru
    Posts
    2,526
    Real Name
    Alan De Enfield
    Local Date
    03-29-2024
    Local Time
    05:36 AM
    Quote Originally Posted by DanL96a1 View Post
    I have had mixed advice on the main sling screw (in front of magazine) being done up tight when not in use or storage. Do you leave Lee Enfield screws done up tight when not in use or leave them tight?

    I would assume it could cause the wood to crack, if left under constant contact/ stress?
    The Front trigger guard screw is not tightened up onto the forend (wood) it is tightened up onto the metal spacer inset into the wood so there is no crushing force on the wood work.

    Leave it tight !!!
    Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...

  4. Thank You to Alan de Enfield For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member DanL96a1's Avatar
    Join Date
    Mar 2009
    Last On
    02-19-2024 @ 04:35 AM
    Age
    41
    Posts
    188
    Local Date
    03-29-2024
    Local Time
    06:36 AM
    Thread Starter
    Thanks for your reply , so I’m the case of Enforcer and L42, which has a plate and spacer removed?

  7. #4
    Advisory Panel Brian Dick's Avatar
    Join Date
    Apr 2008
    Last On
    Yesterday @ 02:10 PM
    Location
    Edgefield, SC USA
    Posts
    4,040
    Local Date
    03-29-2024
    Local Time
    01:36 AM
    You should either replace the plate or fit a guard screw collar. It's there for a reason. In my experience, the "guard screw, front" will loosen with time rather than tighten. Just the normal seasonal expanding and contracting of the wood because of moisture, lack of care, etc. A very wise man told me once to always treat woodwork on a rifle like a living thing. That's why sealed finishes like varnish, polyurethane and others like them were never used on military woodwork.

  8. #5
    Legacy Member Mk VII's Avatar
    Join Date
    Dec 2008
    Last On
    03-20-2024 @ 07:30 PM
    Location
    England
    Age
    62
    Posts
    1,406
    Real Name
    James West
    Local Date
    03-29-2024
    Local Time
    05:36 AM
    Some people do slacken them off in the winter season - but remember to tie a label on it to remind yourself.

  9. #6
    Legacy Member DanL96a1's Avatar
    Join Date
    Mar 2009
    Last On
    02-19-2024 @ 04:35 AM
    Age
    41
    Posts
    188
    Local Date
    03-29-2024
    Local Time
    06:36 AM
    Thread Starter
    Quote Originally Posted by Brian Dickicon View Post
    You should either replace the plate or fit a guard screw collar. It's there for a reason. In my experience, the "guard screw, front" will loosen with time rather than tighten. Just the normal seasonal expanding and contracting of the wood because of moisture, lack of care, etc. A very wise man told me once to always treat woodwork on a rifle like a living thing. That's why sealed finishes like varnish, polyurethane and others like them were never used on military woodwork.
    Hi Brian thanks for reply, in all EMERS and documentation I cannot find a definitive answer. I did have a collar and plate fitted, but the collar was removed as it was no longer required apparently if plate was fitted.

    I tend to give the woodwork a few coats of boiled linseed oilicon, every few weeks. It’s a excellent stress relief and keeps it looking good! But most important the water out!

    All gunsmith of note say leave tight....

    ---------- Post added at 10:33 AM ---------- Previous post was at 10:31 AM ----------

    Quote Originally Posted by Mk VII View Post
    Some people do slacken them off in the winter season - but remember to tie a label on it to remind yourself.
    Yeah i tend to do a thouroght check on all screw, and rifle once out of storage and before shooting. Thanks for advice will put a note around there neck!

  10. Thank You to DanL96a1 For This Useful Post:


  11. #7
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Yesterday @ 04:54 AM
    Location
    Brisbane
    Posts
    2,237
    Local Date
    03-29-2024
    Local Time
    03:36 PM
    There may be a role for an "inch-pound" torque wrench here.

    In shooting disciplines that are out of my financial league, apparently folks use Hex / Torx socket bolts as their trigger-guard screws The idea is that you can "scientifically" test for "optimum" tension and then be able to maintain / repeat it with consistent accuracy.

    One idea is to take a long-shank 1/4" cap / Torx bolt and turn it into something that will fit a No1 or No4. Just remember that the front TG screw on a No4 is a 1/4" ( x 26 tpi) BSF and thus has a 55 deg thread form, The screws on a No1 are 30 TPI, "Enfield special". Most of these fancy socket bolts are grade 6 to 8, thus TOUGH and may require a Carbide thread form tool of the correct form, but every home should have them already......

    More applicable to rifles with L-42 style bedding plates because the "tilt" of a correctly-fitted Lee Enfield trigger-guard is what is really doing a lot of the work of retaining the fore-end during recoil. It is a very fancy wedge. Do not ignore the other part of this retention caper, the "draws" inside the rear of the fore-end. Carefully re-read all of Peter Laidlericon's articles on that subject. In reality, it is not the fore-end "moving forward", but the whole rifle moving rearwards under recoil, AWAY from the mass of the fore-end.

    NOT a Mauser bedding system, nor a Mauser LOCKING system.

    A bit of a study of the ill-fated Canadianicon J-5550 programme is en"lightening".

  12. #8
    Legacy Member Mk VII's Avatar
    Join Date
    Dec 2008
    Last On
    03-20-2024 @ 07:30 PM
    Location
    England
    Age
    62
    Posts
    1,406
    Real Name
    James West
    Local Date
    03-29-2024
    Local Time
    05:36 AM
    Sounds a lot like that 'electric bedding' fad in the 1950s, which we don't hear much about these days - and we don't seem to miss it.

+ Reply to Thread

Similar Threads

  1. Purpose of mid-length sling swivel on No. 4T and Enfield target rifles?
    By Steve762 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 9
    Last Post: 12-30-2015, 06:41 PM
  2. Lee Enfield Sling Swivel
    By Centurion in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 10
    Last Post: 06-27-2012, 05:11 AM
  3. Buttplate swivel screw?
    By Garandrew in forum M1 Garand/M14/M1A Rifles
    Replies: 2
    Last Post: 04-12-2009, 11:30 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks