+ Reply to Thread
Results 1 to 7 of 7

Thread: Zeroing a 1903A3

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Mjac's Avatar
    Join Date
    Mar 2019
    Last On
    Today @ 03:05 PM
    Location
    East TN
    Posts
    5
    Local Date
    03-28-2024
    Local Time
    06:59 PM

    Zeroing a 1903A3

    Hello,
    Lurker and first time poster. I found this thread,
    https://www.milsurps.com/showthread.php?t=52813.
    I was going to revive it but in the interest of playing nice with the powers that be , I didn't. The above post got close to what I was seeking but I still need some guidance.
    My new to me '43 Remington 1903A3 came to me with a bubba'ed front sight. The short blade appeared to be from a non mil rifle. I did not fire it in that condition and have since had it changed out with an "A" blade.
    Today's first firing of several different hand loads yielded some promising groups but they were all slightly right and low. The best 50 yd 5 shot group using 6 o'clock hold on a 8" bull was 5" low. Also slightly to the right but I can fix that later.
    The rear sight was all the way down of course.
    With this information could any one suggest how much I should shorten the "A" blade to give a 200 yd zero? (with a 6 o'clock hold on a 13"? black)


    TIA,
    Mike

    After the sacrificial "A" blade is shortened, the plan is to get an appropriate blade.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel Chuckindenver's Avatar
    Join Date
    Mar 2009
    Last On
    Today @ 12:38 PM
    Location
    Denver Co
    Age
    61
    Posts
    3,152
    Real Name
    chuck
    Local Date
    03-28-2024
    Local Time
    04:59 PM
    shoot it at 100 yards first, then play with the sight..
    warpath metal finishing contact info.
    molinenorski@msn.com
    720-841-1399 during normal bus, hours.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Contributing Member Ovidio's Avatar
    Join Date
    Dec 2016
    Last On
    Today @ 10:52 AM
    Location
    Pordenone, Italy
    Posts
    2,141
    Real Name
    Ovidio Gentiloni
    Local Date
    03-28-2024
    Local Time
    11:59 PM
    I would also dare saying that you might want to shoot the first round at 25 or 50 meters. Just for the sake of it.
    When I bring a new rifle to the range, if the sighting through the muzzle does not convince me, I go short. If the 25 are on paper and close enough to the bullseye that I can be safe shooting at 100, I go right away, without wasting further ammo, otherwise I first want to get there on the short distance. It goes pretty fast doing mistakes, and it pretty much also depends where you shoot and the rules applied there. It is not only a question of safety sometimes...
    In any case, have fun!!!
    34a cp., btg. Susa, 3° rgt. Alpini

  6. #4
    Legacy Member ArtPahl's Avatar
    Join Date
    Jan 2015
    Last On
    03-22-2024 @ 10:51 AM
    Location
    Michigan
    Posts
    192
    Local Date
    03-28-2024
    Local Time
    06:59 PM
    "The rear sight was all the way down of course."

    If you raise the rear sight, you will raise the point of impact at the target.

  7. #5
    Legacy Member gc1054's Avatar
    Join Date
    Jul 2012
    Last On
    10-09-2022 @ 09:31 AM
    Location
    Central PA USA
    Posts
    66
    Local Date
    03-28-2024
    Local Time
    06:59 PM
    Since the 03A3 is new to you suggest you might check the following before starting to adjust the front sight height for elevation zeroing:
    -Action screw tightness front & rear
    -Barrel weight at the forend tip (should be pressure bedded; say 5-7lbs....if low or zero check bedding/stock)
    -Boresight the rifle and check sight alignment

    Also, since you didn't mention the specifics of the hand loaded ammunition you used for the testing note that the sights are calibrated for USGI '06 M2 Ball so try a similar load wrt bullet weight & velocity (150gr MV=2740fps) and see if there's a POI shift.

    If you've gone through a similar set of checks (and even a stripped down inspection) & all seems ok with the bedding/action set up plus the ammo is ok then changing/adjusting the FS height shorter to raise the POI is the next step. IIRC there were 5 FS blade heights marked A-E for adjusting zero elevation.... E was the shortest......the actual heights are on the other post you noted. Or, you can calculate the required change to your A blade using the sight radius /range formula. Keep in mind that the lowest RS setting is 200 yds so with M2 ballistics the POI will be on the order of 2.7" high at 100yds & on POA 200yds. Since you're hand loading you've probably got this covered👍

    The right windage error you noted should take a few left clicks on the RS windage knob to correct.... But suggest waiting to fine tune until after the FS blade is set.

    Final thought, for the 6oc hold on the 13" black (POI 6.5" above POA) after setting up the elevation as noted above (POI=POA at 200yd target with RS on 200) simply set the RS slider to 300 yds. If you're shooting M2 ball ballistics it should get you pretty close to the 10 ring on the SR target.

    Enjoy you're new 03A3.... Nice rifles!
    Last edited by gc1054; 03-29-2019 at 12:03 AM.

  8. #6
    Legacy Member Mjac's Avatar
    Join Date
    Mar 2019
    Last On
    Today @ 03:05 PM
    Location
    East TN
    Posts
    5
    Local Date
    03-28-2024
    Local Time
    06:59 PM
    Thread Starter
    gc1054,

    Thank you for condensing many of the things I have read here and elsewhere into a much simpler format which outlines the route I have already trudged. While I do not and probably never will have ball ammo, my hand loads were developed with replication in mind. I believe I have come close enough. Earlier range time with my other '06's helped in this area.
    I am currently traveling and haven't gotten back to working with the sights but perhaps later next month I can post my front sight changes.

    Btw, the following link has helped, and as you have accurately noted, a 200 yd lowest RS setting is what I am chasing.

    1903a3 accuracy and targeting test/specs/zero - CMP Forums

    Thanks again.
    "My two most favorite people are Navy Corpsmen and Marine medivac helicopter pilots" - MEJ 1967.

  9. #7
    Legacy Member gc1054's Avatar
    Join Date
    Jul 2012
    Last On
    10-09-2022 @ 09:31 AM
    Location
    Central PA USA
    Posts
    66
    Local Date
    03-28-2024
    Local Time
    06:59 PM
    Another benefit of setting up the sights as noted above is that they are quite useable over moderate ranges. I set my 03A3 up in a similar way and always use it in CMPicon games (200 yd....6oc hold with RS at 300) and occasionally in High Power matches over 200, 300, 600 yds with tweaked "M2-type" hand loads (run 155gr AMAX at 2750-2800...set the RS in a similar way at the different ranges) Things loosen up a bit group-wise at 600yds but some of that is me not seeing as well these days. And there's always some "hold adjustment" required. The fun benefit is that you can set up milk jugs at 300yds.....set the RS to 300 and shoot knowing you'll be close & with no need to think too much about..... "let's see... At 200 I'm 6" high on a SR target with 6oc hold....so at 300 POI is going to be....." Makes for more instinctive & fun shooting IMHO.

    Have fun & a good shooting season.
    Last edited by gc1054; 03-29-2019 at 11:17 PM.

+ Reply to Thread

Similar Threads

  1. Zeroing a No.32 scope
    By kryten in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 15
    Last Post: 07-31-2017, 04:35 AM
  2. Zeroing Question
    By Chubbs in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 10
    Last Post: 04-22-2017, 04:04 PM
  3. Zeroing the L42
    By CODFan in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 9
    Last Post: 06-04-2014, 11:14 AM
  4. Brief zeroing seesion with the old No.4 Mk.I (T) and the No.3 (T)
    By jmoore in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 14
    Last Post: 11-13-2012, 02:50 AM
  5. #4 Mk1(T) Zeroing
    By 676161 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 1
    Last Post: 09-22-2008, 03:48 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks