+ Reply to Thread
Page 2 of 2 FirstFirst 1 2
Results 11 to 18 of 18

Thread: War Baby Vols. 1-3

Click here to increase the font size Click here to reduce the font size
  1. #11
    Advisory Panel
    painter777's Avatar
    Join Date
    Mar 2009
    Last On
    @
    Location
    Central Michigan
    Posts
    4,280
    Local Date
    11-14-2019
    Local Time
    04:22 PM
    Snowman,
    I worry about how far the 2 screw plugs sit inside the left bolt lug track.
    Do you think it will be hard to grind them down?
    Would you try grinding them in place or pull them then grind off the extra ?
    Wonder if a local Smith might have some scope plugs that are shorter and would fit?
    Or maybe one of the on line suppliers... if you could figure out the measurements of them.

    * Anyone have an opinion of if he really needs screw plugs in it?
    Would he be OK without the holes being plugged?

    Can you give us most of the S'G' serial # ?
    IDK if a late S'G' after the SG take over used any SG barrels.
    But that may be a good place to start searching for info.
    IIRC after the take over, SG parts can be found on S'G' carbines......... Maybe even barrels.



    If mine I'd detail clean the heck out of, including a good cleaning of the stock.

    Thanks for the pictures, I think you did very well.
    Charlie-Painter777

    A Country Has No Greater Responsibility Than To Care For Those Who Served...

  2. Thank You to painter777 For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    Banner AD Space Available - Click HERE to Inquire We specialise in military utensils and artefacts such as helmets, daggers, medals and badges, etc.  The on-line store is intended for personal browsing and searching of collecting objects. All items are provided historical value only and can be used for home collection or other purposes except of fascism, Nazism or other extremism manifestation or its propaganda. LIMITED TIME OFFER FROM THE AMERICAN GUNSMITHING INSTITUTE: Get Immediate Online Access To AGI's NEW Armorer's Course for Glock Pistols, Covering Every Generation of Glocks, Including the Latest Model 42/43 and Double Stack Pistols for ONLY $7.00! Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Chuck in Denver ... Buy-Sell-Trade .. Guns, Cars Motorcycles Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses. Banner AD Space Available - Click HERE to Inquire
     

  4. #12
    Really Senior Member deldriver's Avatar
    Join Date
    Dec 2010
    Last On
    10-17-2019 @ 11:02 AM
    Location
    Tennessee
    Posts
    393
    Local Date
    11-14-2019
    Local Time
    05:22 PM
    If there's a question whether an SG barrel is the original one just post a picture of the barrel proof P. An SG barrel proof is pretty distinctive in it's size and shape versus an S'G' proof.

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #13
    Really Senior Member Snowman1510's Avatar
    Join Date
    Dec 2016
    Last On
    11-05-2019 @ 09:47 PM
    Location
    Texas
    Posts
    251
    Local Date
    11-14-2019
    Local Time
    03:22 PM
    Thread Starter
    I will get back to you on the barrel questions when I get some time off work. And off the top of my head the carbine is a 3.6 mil then Id have to look at the rest of the rec.

    I will probably pull the screws out and grind them down. One is loose already. I don't know how to measure do that though.
    “There are three kinds of men. The ones that learn by readin’. The few who learn by observation.
    The rest of them have to pee on the electric fence for themselves.” - Will Rogers

  7. #14
    Really Senior Member shadycon's Avatar
    Join Date
    Jun 2009
    Last On
    11-11-2019 @ 10:06 AM
    Location
    NRV, Va.
    Posts
    733
    Local Date
    11-14-2019
    Local Time
    04:22 PM
    Suggestion on screws: Get new screws. If threads are bad you may have to go 1 size larger. Use fine thread screws. Screw them in from inside, if you can go a little deep, carefully cut off with Dremel tool. Unscrew until flush on inside, if you need to take more off, repeat process. When satisfied, you an screw them in from outside and lock tight them.
    Last edited by shadycon; 06-10-2019 at 09:55 AM.
    M1a1's-R-FUN!!!!!!!!!!!!!!!!!!!!!!!!
    TSMG's-R-MORE FUN!!!!!!!!!!!!!
    ENJOY LIFE AND HAVE FUN!!!

  8. Thank You to shadycon For This Useful Post:


  9. #15
    Member JackP's Avatar
    Join Date
    May 2014
    Last On
    Today @ 04:08 PM
    Location
    Cloudcroft, NM
    Posts
    15
    Local Date
    11-14-2019
    Local Time
    02:22 PM
    Snowman, It appears that your receiver has been drilled and tapped for a Weaver side mount bracket, typical of what was used on Universal carbines. It has been positioned rearward of the normal location on a Universal, probably to avoid having to drill and tap the forward screw into a blind hole in the receiver where the barrel screws into the receiver. The receiver is really too thin in this area to leave enough threads for a tight fit , often resulting in the screw being allowed to protrude a little into the bolt track. What happens is, even though the bolt feels free to travel in the track, under high pressures and speeds, the left lug will drag on the protruding screws enough to cause excessive forces to be exerted on the right bolt lug, causing it to break off. This happened to one of my carbines. It is a bad design!! I would suggest removing the plugs completely and check to see that there are no remaining burrs from the threads that can contact the bolt lug. Also, inspect the left bolt lug for any evidence of wear or damage.

  10. The Following 2 Members Say Thank You to JackP For This Useful Post:


  11. #16
    Really Senior Member Snowman1510's Avatar
    Join Date
    Dec 2016
    Last On
    11-05-2019 @ 09:47 PM
    Location
    Texas
    Posts
    251
    Local Date
    11-14-2019
    Local Time
    03:22 PM
    Thread Starter
    JackP,

    When I bought the Carbine, I immediatley checked for wear on the left lug because I noticed it dragging on the screws. The lug is fine and I backed out the offending screw for the time being. Are you suggesting just taking the screws out completely, or buying new screws as shadycon suggested?

    Or should I go with my original plan of just shortening down the 4 existing ones.

    Painter777, the carbine's serial is 3,640,184
    “There are three kinds of men. The ones that learn by readin’. The few who learn by observation.
    The rest of them have to pee on the electric fence for themselves.” - Will Rogers

  12. #17
    Member JackP's Avatar
    Join Date
    May 2014
    Last On
    Today @ 04:08 PM
    Location
    Cloudcroft, NM
    Posts
    15
    Local Date
    11-14-2019
    Local Time
    02:22 PM
    Yes, I would remove the screws completely. How are you going to prevent shorter screws from loosening and eventually interfering with the bolt? I don't see any real need to plug the holes.

  13. #18
    Really Senior Member Snowman1510's Avatar
    Join Date
    Dec 2016
    Last On
    11-05-2019 @ 09:47 PM
    Location
    Texas
    Posts
    251
    Local Date
    11-14-2019
    Local Time
    03:22 PM
    Thread Starter
    What is the point of having the screws in the rec. is it to make it look cosmetically better or does it add some lost rigidity?
    “There are three kinds of men. The ones that learn by readin’. The few who learn by observation.
    The rest of them have to pee on the electric fence for themselves.” - Will Rogers

+ Reply to Thread
Page 2 of 2 FirstFirst 1 2

Similar Threads

  1. War Baby & War Baby comes home
    By JBBOOKS in forum WTS/WTB/WTT (Want to Sell, Buy or Trade) Forum
    Replies: 0
    Last Post: 02-01-2019, 09:12 AM
  2. War Baby 3
    By phillydude in forum M1/M2 Carbine
    Replies: 13
    Last Post: 12-15-2013, 01:06 PM
  3. War Baby
    By Steven Martin in forum M1/M2 Carbine
    Replies: 17
    Last Post: 04-20-2013, 04:53 PM
  4. New Baby
    By Tatsudoshi in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 1
    Last Post: 11-23-2009, 08:37 PM
  5. My New Baby
    By gandog56 in forum Milsurps General Discussion Forum
    Replies: 6
    Last Post: 08-07-2008, 03:37 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts