+ Reply to Thread
Results 1 to 8 of 8

Thread: The ZFK55 Scope

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Pierre's Avatar
    Join Date
    Aug 2018
    Last On
    01-06-2024 @ 11:13 AM
    Location
    Lost Prairie Montana
    Posts
    163
    Real Name
    Pierre St. Marie
    Local Date
    03-28-2024
    Local Time
    05:15 AM

    The ZFK55 Scope

    First, unless you are very experienced in servicing Swissicon Scopes........ do not attempt disassembly.
    My visiting Father In Law is extremely experienced. One of the three who developed the world's first Atomic Microscope for Stanford University, R&D Head of Dept. for Jenkyl & Davidson, Head of R&D for Swift Instruments and a few other I don't remember........ he's qualified to do the job. This is what he discovered, and this applies to all zfk55 scopes.

    All of them come with windage/elevation ball detents, however few of them can actually be felt when turning the knobs. Reason? Highly likely weak or broken springs under the single ball itself. A hole, the exact size of the ball and the spring is drilled into steel ring container. The spring is dropped in, the ball goes in on top of it and then the edge of the drilled hole is very gently and precisely "peened" with a circular tool of the correct diameter, trapping the ball just above diameter center.

    There is, apparently, grease of a synthetic base in that ball detent hole as well as in the outer casing. The age may be the culprit for that spring to have weakened. Without that spring pressure, the ball simply either engages the detents very weakly or not at all. We're field testing on sent to us today. It did have a small screw floating in the windage housing, but that was only the reason for the reticle "jumping". The spring in this particular scope is either broken or extremely weak.

    Having reassembled the turret, we found that there is very little resistance in the turret knob. We'll have two options to offer the owner later today. One, disassemble, remove the ball and spring, re-drill that hole 1/1000th larger, use a ball that's 1/1000th larger than the original and actually fabricate the required tool for "peening". Fortunately, my FIL is a machinist and more importantly, a micro-machinist. No ideas as of yet on the cost of doing this initial process, but both turrets would need to be done.

    Second option: Add an extremely heavy grease, filling the inside of the turret to stabilize it an prevent the reticle from moving when the rifle is fired. We'll see about that one with field testing, so................

    Don't get too bothered about your scope not registering either felt, or actual detent locking. You're all (including me) in the same boat
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. The Following 2 Members Say Thank You to Pierre For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Legacy Member Pierre's Avatar
    Join Date
    Aug 2018
    Last On
    01-06-2024 @ 11:13 AM
    Location
    Lost Prairie Montana
    Posts
    163
    Real Name
    Pierre St. Marie
    Local Date
    03-28-2024
    Local Time
    05:15 AM
    Thread Starter
    and...... Standby. He's found a third option and he's dis-assembling again. LOL

  5. Thank You to Pierre For This Useful Post:


  6. Avoid Ads - Become a Contributing Member - Click HERE
  7. #3
    Legacy Member Pierre's Avatar
    Join Date
    Aug 2018
    Last On
    01-06-2024 @ 11:13 AM
    Location
    Lost Prairie Montana
    Posts
    163
    Real Name
    Pierre St. Marie
    Local Date
    03-28-2024
    Local Time
    05:15 AM
    Thread Starter
    This is the rest of the running conversation from another forum.

    ================================================

    Seems that the manual says you can't hear or feel it. We can definitely feel it if you turn it slowly. That

    "feel" will depend entirely on the depth of engagement by the ball. A bit confusing as the manual says

    "no".

    ================================================== =========

    Decision made 10 minutes ago by Grandpa. He is taking it back to the coast when he leaves. He needs his equipment and he'll be micro-machining a complete set of tools for working on these zfk55 scopes.

    I'll let everyone concerned know when he's in a position to take care of your scopes. Be advised, he's nearly 91 years old and if he tires or it or is deluged with too many requests, there may be a time lag of a few months before he can supply Latigo with a complete set of tools and instruct him in detail as to the disassembly repair and reassembly of these scopes. It's not a simple process.

    We have determined that Petrov's scope has indeed been disassembled and reassembled by someone who did no know what they were doing, and... we did find a small screew floating in the turret once again....... I reiterate that the windage detents can absolutely be felt, albeit lightly. The moa function in windage seems to be in the neighborhood of 1/8th moa. These other scopes are the norm, not the exception. I'll let you know about elevation later in the next few days. Petrov's must be disassembled and inspected anyway. That turret does seem to be different than the windage, but "how" has yet to be determined.

    There may be an optics expert in your neck of the woods, but before you hand it over to him to "look and see", be damned sure of his qualifications.
    ================================================== ==

    There is no ball and no spring in Petrov's elevation turret. There IS a place for them and there are detents, however, he noted that the slight "peening" required to retain the ball is not there and never has been. That leads him to believe that in the elevation system, they were not required as the turret is manufactured with built in "resistance" holding the elevation line tightly in place. Mine seem to be the same.

    He intends to have a supply of the correct balls and springs on hand to install in the elevation turrets. I'd feel better "feeling" those detents as they are in my windage. That will be an option offered to any zfk55 mount owners that choose to do so.

    ==================================================

    Now we know why the ball/spring is not necessary in the elevation turret........The Elevation turret has a very strong compression washer in it to hold it in adjustment. The hole is there and the detents are there, but no ball or spring. Today we're doing a test on the elevation turret. We're installing a ball and spring just to see how it works, but I can tell you that the compression washer is very strong, so there is no need for the ball and spring.

    It's just interesting that is set up exactly like the windage. If you cannot actually feel the ball/detent clicks in your windage, then you definitely have a problem.
    P

    ================================================== ======

    The drilled hole for the ball is simply a pre-sizing hole. It's not the trued and finished size required for the ball. Because of that, the ball would not fit, so....... not required. The Tension Washer does the job.
    P

  8. #4
    FREE MEMBER
    NO Posting or PM's Allowed
    Miller Tyme's Avatar
    Join Date
    Nov 2016
    Last On
    Yesterday @ 03:50 PM
    Location
    Where men are men and sheep are nervous
    Posts
    143
    Local Date
    03-28-2024
    Local Time
    04:15 AM
    +1, no ball & spring under my elevation turret, only on the windage turret.

  9. #5
    Legacy Member Pierre's Avatar
    Join Date
    Aug 2018
    Last On
    01-06-2024 @ 11:13 AM
    Location
    Lost Prairie Montana
    Posts
    163
    Real Name
    Pierre St. Marie
    Local Date
    03-28-2024
    Local Time
    05:15 AM
    Thread Starter
    We'll be handling both zfk55 as well as the k31/43 scope repairs and renovations.
    We now have the capabilities of Micro-Machining.
    Both Edelweiss and Simpson's are our first customers.

    P

  10. #6
    Legacy Member NearSightedSniper's Avatar
    Join Date
    Mar 2012
    Last On
    03-06-2024 @ 09:12 PM
    Location
    Morgantown Pa
    Posts
    27
    Real Name
    Mick
    Local Date
    03-28-2024
    Local Time
    04:15 AM
    1st off thank you for this undertaking. I know it can't be easy.
    2nd, lately I have been looking @ buying a ZFK 55 from Simpsons, if I were to buy one from them could I assume that the scope has undergone treatment with you guys? Or does it depend on the scope? Basically I guess what I'm asking is do all of the ZFK optics need this performed or just some of the more "used" ones?
    Thanks, Mick

  11. #7
    Legacy Member Pierre's Avatar
    Join Date
    Aug 2018
    Last On
    01-06-2024 @ 11:13 AM
    Location
    Lost Prairie Montana
    Posts
    163
    Real Name
    Pierre St. Marie
    Local Date
    03-28-2024
    Local Time
    05:15 AM
    Thread Starter
    . Good morning Mick. Both Simpson's and Edelweiss have gotten their notices from us of that service. They both told us the same thing. If the scopes were clouded or in the case of the zfk55, the windage tour it not having clicks that can be easily felt, they would refer the customer to us.

    The reason for that from both of them is that it would require shipping those scopes to us individually and with those scopes being irrreplaceable, the insurance would be skyhigh for shipping. We're not sure if they informed all of their sales personnel of that service being available, and we don't really know if they even test the rifles before they ship them to the customer. We only just recently thought about sending both of them a stack of business cards for scope repair.

    Check your rifle when it comes in, and if the windage turret MOA clicks cannot be felt, then it will require a maintenance. The elevation turret will not have MOA clicks but should have a fair bit of resistance when moving it up or down. The elevation turret works with a heavy tension washer for quick adjustments in the field.

    Go to swissproductsUSA.com and call us on the helpline for discussion and shipping information, but I do hope yours is fully functioning and clear.
    Pierre

    ---------- Post added at 12:04 PM ---------- Previous post was at 11:59 AM ----------

    ... And Mick, I forgot to add that simple storage with little or no use of those turrets can allow the grease to become very thick or even solidify and that will make you unable to feel the MOA clicks. If you do buy one and have that problem, call the helpline and we'll explain the entire process before you decide whether or not to ship it.
    P
    Last edited by Pierre; 10-19-2019 at 12:06 PM.

  12. #8
    Legacy Member NearSightedSniper's Avatar
    Join Date
    Mar 2012
    Last On
    03-06-2024 @ 09:12 PM
    Location
    Morgantown Pa
    Posts
    27
    Real Name
    Mick
    Local Date
    03-28-2024
    Local Time
    04:15 AM
    Quote Originally Posted by Pierre View Post

    Check your rifle when it comes in, and if the windage turret MOA clicks cannot be felt, then it will require a maintenance. The elevation turret will not have MOA clicks but should have a fair bit of resistance when moving it up or down. The elevation turret works with a heavy tension washer for quick adjustments in the field.

    Go to swissproductsUSA.com and call us on the helpline for discussion and shipping information, but I do hope yours is fully functioning and clear.
    Pierre


    I will do that Pierre, I'm hoping to "finally" buy a ZFK 55 in January or Febuary. I will be in touch I'm sure.
    Quote Originally Posted by Pierre View Post
    Quote Originally Posted by Pierre View Post
    ... And Mick, I forgot to add that simple storage with little or no use of those turrets can allow the grease to become very thick or even solidify and that will make you unable to feel the MOA clicks.
    P
    The same thing was said to me about the clicks on my No32 scope but luckily they were fine.

    Thanks again, Mick

+ Reply to Thread

Similar Threads

  1. Swiss Miss/ ZFK55
    By Miller Tyme in forum Swiss Rifles
    Replies: 17
    Last Post: 06-23-2019, 11:22 AM
  2. ZfK55 value/info please
    By Kiwi in forum Swiss Rifles
    Replies: 11
    Last Post: 09-02-2013, 06:26 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks