+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15

Thread: Legit, or hand-made block?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-28-2024
    Local Time
    04:29 PM

    Legit, or hand-made block?

    Hello Martini enthusiasts!

    A fellow asked me to look at his Martini carbine. Was able to get this out of the frame. Leaves me wondering if it's a trustworthy part. I tested the action before taking it apart with an empty cartrige but with a new primer. The primer strike was so off-center it almost missed the primer. It was right on its edge.

    Looking at it from the front, it is obviously asymetrical. Only stamp visible is a "T.D" upside down on its right side. There is no retaining screw on the back face.

    Any opinion or advice?






    ---------- Post added at 09:30 PM ---------- Previous post was at 09:22 PM ----------

    Found this other mark on it

    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Age
    2010
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 06:54 AM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,392
    Real Name
    Daan Kemp
    Local Date
    03-28-2024
    Local Time
    11:29 PM
    Looks really rough. What does the rest of the action look like/

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-28-2024
    Local Time
    04:29 PM
    Thread Starter
    i'll try to take pics of the action tonight after work. The action does look good, scrubbed of all markings though (looks refinished)

  6. #4
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    11:29 PM
    The depression that accepts the cartridge and guides it into the chamber looks like a proper piece of machining. Combined with the genuine-looking stamp and one could say that the top surface is "legit". But the other photos show rough surfaces that should not be present on any factory-milled block. Furthermore, they are surfaces that are not exposed to damage through rough usage. Add in the asymmetry and I wonder whether this is a block from a different Martini-style action that has been hand-carved to fit the rifle.

    ??? Thoughts, anyone???
    Last edited by Patrick Chadwick; 07-10-2019 at 06:19 PM.

  7. Thank You to Patrick Chadwick For This Useful Post:


  8. #5
    Moderator
    (The Restorers Corner)

    louthepou's Avatar
    Join Date
    Dec 2007
    Last On
    03-01-2024 @ 05:42 PM
    Location
    Near Ottawa, Canada
    Age
    53
    Posts
    542
    Real Name
    Louis Rene
    Local Date
    03-28-2024
    Local Time
    04:29 PM
    Thread Starter
    Thanks Patrick, appreciated

    Just to add to the fun, here's how off-center the firing pin strike is:


  9. #6
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    11:29 PM
    Lou, you need to know in which direction the off-centre lies. Hard to tell when the case has been extracted!

    Up/down direction can be a result of an error in the block closing position. Left/right is the block itself. Both of these possibilities could result from the use of a non-original block.

    So I recommend that you make a test with a case that has a clear mark at 12 o'clock, so that when the case is extracted we can see in which direction the displacement lies.

  10. #7
    Legacy Member Simon P's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 04:11 AM
    Location
    Essex. UK.
    Posts
    636
    Real Name
    Simon Pemberton
    Local Date
    03-28-2024
    Local Time
    09:29 PM
    Quote Originally Posted by louthepou View Post
    Hello Martini enthusiasts!

    A fellow asked me to look at his Martini carbine. Was able to get this out of the frame. Leaves me wondering if it's a trustworthy part. I tested the action before taking it apart with an empty cartrige but with a new primer. The primer strike was so off-center it almost missed the primer. It was right on its edge.

    Looking at it from the front, it is obviously asymetrical. Only stamp visible is a "T.D" upside down on its right side. There is no retaining screw on the back face.

    Any opinion or advice?

    https://www.milsurps.com/images/impo.../4h2qfHu-1.jpg
    https://www.milsurps.com/images/impo...01PCjpg1-1.jpg
    https://www.milsurps.com/images/impo...qDfCjpg1-1.jpg
    https://www.milsurps.com/images/impo.../K0s21zt-1.jpg

    ---------- Post added at 09:30 PM ---------- Previous post was at 09:22 PM ----------

    Found this other mark on it

    https://www.milsurps.com/images/impo...m1Jrjpg1-1.jpg
    It looks like the Birmingham Definitive Proof Mark used between 1887 & 1904, probably a Birmingham Trade Rifle
    Regards Simon

  11. #8
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    11:29 PM
    Quote Originally Posted by Simon P View Post
    It looks like the Birmingham Definitive Proof Mark used between 1887 & 1904, probably a Birmingham Trade Rifle
    Could you please explain that? What is the difference to the mark introduced in 1868? The width of the depression for the cartridge - far more than required for a .303 case - makes me rather think that the block was originally for a large-bore case (577-450 or Greener special). I do not have a .303 Martrini carbine for comparison, but are the blocks narrower than in the older large-bore systems?

  12. #9
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    11:29 PM
    This thread suffered from a glitch that seems to have been caused by my previous post #6, in which I posted a link to the Proof Act of 1868 that introduced the VGP (London) or VBP (Birmingham) proof mark. The logical jam in the thread has now been cleared, but part of my post is missing, thus making my post #8 a bit confusing.

    In the missing text I had already pointed out that the mark on the upper face of the block looked like that introduced in 1868, which basically continued in the same form until 1925. Hence my question to Simon P : what was the difference in marking from 1887 to 1904, as my sources show the mark as being unchanged throughout?

  13. #10
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Today @ 04:54 AM
    Location
    Brisbane
    Posts
    2,237
    Local Date
    03-29-2024
    Local Time
    07:29 AM
    Regarding the "off-centre" primer strike:

    Firstly, remember that these beasties were originally built for a rather "loose-fitting" cartridge which had a primer of somewhat greater diameter than the .210" modern "Large Rifle" type. Thus, as long as the striker whacked the primer somewhere near the middle, the round fired.

    Since that MH in question was built, who knows what bits of the block and other parts have worn or been replaced? Has the chamber ever been "refreshed" to remove pitting? The old foil rolled cases had their problems but embedding into the chamber wall seems to have not been one of them. Around these parts, I doubt anyone has fired a brass-foil round since WW2, so, if there are any hard-core purists out there with recent experience firing genuine, vintage ammo in their Martinis, feel free to chime in. Cartridge collectors will be crying in their beers. "Modern" drawn brass is more likely to stick in a pitted chamber, especially with "proper" loads, hence the business of polishing out any pits.
    Last edited by Bruce_in_Oz; 07-29-2019 at 10:49 PM.

  14. Thank You to Bruce_in_Oz For This Useful Post:


+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. Hows this hand made stock
    By CINDERS in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 18
    Last Post: 08-27-2015, 05:22 PM
  2. 14-314a Garand Picture of the Day - hand-to-hand combat demonstration,
    By Mark in Rochester in forum M1 Garand/M14/M1A Picture of the Day Forum
    Replies: 3
    Last Post: 11-13-2014, 08:54 PM
  3. Saginaw S'G' in IP Block 1762250 1st Block
    By Rustship in forum M1/M2 Carbine
    Replies: 16
    Last Post: 05-18-2012, 10:17 PM
  4. Who Made The Narrowest Hand Guard?
    By painter777 in forum M1/M2 Carbine
    Replies: 2
    Last Post: 12-17-2010, 02:33 PM
  5. New pics, old and hand made knives of WW II
    By sdh1911 in forum Edged Weapons Forum
    Replies: 0
    Last Post: 02-13-2007, 11:03 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks