+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15

Thread: Removing rear handguards - two methods

Click here to increase the font size Click here to reduce the font size
  1. #1
    Moderator
    (M1 Garand/M14/M1A Rifles)
    Bob Womack's Avatar
    Join Date
    Mar 2009
    Last On
    Today @ 01:07 PM
    Location
    Somewhere Between Clever and Stupid
    Posts
    3,396
    Real Name
    Bob Womack
    Local Date
    03-28-2024
    Local Time
    02:18 PM

    Removing rear handguards - two methods

    Okee dokee. There appear to be two methods to remove the handguard:
    1. Remove gas cylinder assembly, ferrule, and front guard, then drift the pin from the lower band and remove band by "walking" it up the barrel. Then slide off the guard.

    ...or

    2. Carefully un-clip the spring band on the rear guard, tip up from the rear, and remove, a-la the CMPicon site and "Charles."

    Which is the G.I. way?
    Which is your favorite way?

    Thanks!

    Bob
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    Ernie's Avatar
    Join Date
    Mar 2009
    Last On
    11-05-2017 @ 07:14 PM
    Location
    Midwest
    Posts
    34
    Local Date
    03-28-2024
    Local Time
    01:18 PM

    I do #1

    Mostly because I don't like putting tension on the rear handguard clip. It is easy to break the rear handguard, either by chipping out a portion of wood at that location or causing a crack.

    The risk with #1 is scratching the barrel but I have done this probably well over 100 times and find that I seldom ever have a problem. If I do scratch it Brownells makes a solution called Dicropan that covers it nicely.

    Just my two cents worth..........

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    U.S.G.I.'s Avatar
    Join Date
    Mar 2009
    Last On
    07-13-2017 @ 08:06 PM
    Location
    Indiana
    Posts
    171
    Local Date
    03-28-2024
    Local Time
    02:18 PM

    I wouldn't do #2

    I do #1 and I have never did any damage at all.

    I would never try and do #2 handguards are to expensive to replace.

  6. #4
    FREE MEMBER
    NO Posting or PM's Allowed
    fred_ex's Avatar
    Join Date
    Sep 2007
    Last On
    08-11-2019 @ 04:48 PM
    Posts
    17
    Local Date
    03-28-2024
    Local Time
    02:18 PM
    I've always found reinstalling the rear guard by reversing the #2 method
    to be a risky adventure. So I remove everything from the barrel to begin
    with, so I won't be tempted....

  7. #5
    Contributing Member Mark in Rochester's Avatar
    Join Date
    Mar 2009
    Last On
    03-26-2024 @ 12:43 PM
    Location
    Rochester, New York
    Posts
    6,633
    Real Name
    Mark in Rochester
    Local Date
    03-28-2024
    Local Time
    02:18 PM
    If there is a space between the rear of the handguard and the receiver face No 2 will work - if it is tight you will split the handguard.

  8. #6
    Senior Moderator
    (Milsurp Forums)
    Bill Hollinger's Avatar
    Join Date
    Mar 2009
    Last On
    Today @ 11:35 AM
    Location
    Pacific Northwest, Oregon
    Posts
    6,021
    Real Name
    Bill Hollinger
    Local Date
    03-28-2024
    Local Time
    11:18 AM
    I'd go with #1
    Bill Hollinger

    "We're surrounded, that simplifies our problem!"

  9. #7
    Advisory Panel
    Rick B's Avatar
    Join Date
    Mar 2009
    Last On
    03-25-2024 @ 12:30 PM
    Location
    Hinckley, Ohio
    Posts
    502
    Real Name
    RICHARD BORECKY
    Local Date
    03-28-2024
    Local Time
    02:18 PM
    The only problem I see with removing the lower band pins is if it is staked and never been removed you ruin the value. I would make a note of this as someone with a nice Lend Lease for instance would devaluate the piece immediately if they punch the pin out. It would be called a put together if a collector notice this.

    Just food for thought. Rick Bicon

  10. #8
    FREE MEMBER
    NO Posting or PM's Allowed
    0311Shooter's Avatar
    Join Date
    Mar 2009
    Last On
    09-20-2009 @ 05:46 PM
    Location
    South of the Mason/Dixon
    Posts
    230
    Local Date
    03-28-2024
    Local Time
    01:18 PM
    Have done it the #2 method hundreds of times, not one problem.

    I assume it's done my way.

    Remove all internal parts, turn barrel receiver up side down, place on something soft, towel, big rag, piece of foam. With a sharp awl or large nail, insert into one of the holes in the clip, using the barrel as a fulcrum, pry clip away from barrel just enough to clear the lip. Move to the other hole, do the same, then turn over and lift off the perfect handguard assembly. It may be sitting on the towel anyway.

    Can't get any more simpler than that, Private.

  11. #9
    FREE MEMBER
    NO Posting or PM's Allowed
    mongo's Avatar
    Join Date
    Mar 2009
    Last On
    11-26-2009 @ 01:17 AM
    Location
    USA
    Posts
    19
    Local Date
    03-28-2024
    Local Time
    01:18 PM
    I agree with shooter, That is the best way, The thing to remember is not to put any pressure on the rear handguard, only on the clip. And when installing a rear handguard apply thumb pressure only to the clip. You cant split the handguard if you dont pry on it. Be sure it is all the way foward into the lower band and you have enough clearence not to splinter it on the front of the reciever. I have done it that way many times and have never broken a rear hand guard, I use a small hammer on the punch/nail with very light blows to remove the handguard. Tom
    Last edited by mongo; 03-24-2009 at 12:55 AM. Reason: left out important item

  12. #10
    FREE MEMBER
    NO Posting or PM's Allowed
    M2HB's Avatar
    Join Date
    Mar 2009
    Last On
    08-16-2009 @ 08:45 PM
    Posts
    19
    Local Date
    03-28-2024
    Local Time
    11:18 AM
    Quote Originally Posted by 0311Shooter View Post
    Have done it the #2 method hundreds of times, not one problem.

    I assume it's done my way.

    Remove all internal parts, turn barrel receiver up side down, place on something soft, towel, big rag, piece of foam. With a sharp awl or large nail, insert into one of the holes in the clip, using the barrel as a fulcrum, pry clip away from barrel just enough to clear the lip. Move to the other hole, do the same, then turn over and lift off the perfect handguard assembly. It may be sitting on the towel anyway.

    Can't get any more simpler than that, Private.
    That is the method that I use. I have a drift pin for one side of the clip and a 16 penny nail for the other side. I put a gun cleaning patch between the drift pin/nail and the barrel before I pry the clip away. I have never had to remove the barrel band yet to get a clip off.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. The fore-end and handguards of the L42 (by Peter Laidler)
    By Badger in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 0
    Last Post: 11-28-2008, 08:09 AM
  2. Removing frightening rear guard screws on Enfields
    By Cantom in forum Gunsmithing for Old Milsurps
    Replies: 11
    Last Post: 12-26-2006, 02:49 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks