+ Reply to Thread
Results 1 to 9 of 9

Thread: HELP! What caliber is a Gecado Sul bolt action rifle?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    Yesterday @ 04:14 PM
    Location
    Desert Hot Springs, California
    Posts
    1,053
    Real Name
    Walt Meyer
    Local Date
    03-28-2024
    Local Time
    09:27 AM

    HELP! What caliber is a Gecado Sul bolt action rifle?

    I have been working on my friend's small rimfire rifle. It is marked "Gecado Suhl" on the barrel with the number "39" marked on the bolt and barrel. The barrel has a small chamber that will not accept a .22 caliber round. The barrel opens up widely after several inches into a diameter of approximately
    .30 caliber. it is a single shot. Can anyone please advise what the caliber would be and why the barrel is sized so strangely? Thanks!
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. Thank You to Singer B For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Legacy Member Sunray's Avatar
    Join Date
    Mar 2009
    Last On
    03-29-2021 @ 03:01 PM
    Location
    London, Ontario
    Posts
    1,053
    Local Date
    03-28-2024
    Local Time
    10:27 AM
    "...barrel opens up widely after several inches..." That means the barrel is no good. Barrels should not get larger.
    "...will not accept a .22 caliber round..." Which one? It could be a short, long or long rifle.
    Anyway, "GECADO" was the trade name of the company G.C.Dornheim A.G in Suhl/Germanyicon. They were an importer. There were .22 rifles and sporter Mausers and some hand guns.
    Spelling and Grammar count!

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    Yesterday @ 04:14 PM
    Location
    Desert Hot Springs, California
    Posts
    1,053
    Real Name
    Walt Meyer
    Local Date
    03-28-2024
    Local Time
    09:27 AM
    Thread Starter
    Quote Originally Posted by Sunray View Post
    "...barrel opens up widely after several inches..." That means the barrel is no good. Barrels should not get larger.
    "...will not accept a .22 caliber round..." Which one? It could be a short, long or long rifle.
    Anyway, "GECADO" was the trade name of the company G.C.Dornheim A.G in Suhl/Germanyicon. They were an importer. There were .22 rifles and sporter Mausers and some hand guns.
    The barrel is very strange. The chamber will not accept a standard .22 LR round. The last half of the barrel is more like a hollow shroud that the chamber/true barrel is inserted into. It is not shot out, but rather, that is how it is designed. Maybe it is designed to shoot a larger projectile from the larger section using a blank in the smaller chamber?

  7. Thank You to Singer B For This Useful Post:


  8. #4
    Legacy Member old rockape's Avatar
    Join Date
    Mar 2017
    Last On
    12-30-2021 @ 02:00 PM
    Location
    U.K.
    Posts
    24
    Local Date
    03-28-2024
    Local Time
    02:27 PM
    You probably have a training or a Zimmer rifle. Both are for indoor use. It will be chambered for the 6mm Flobert, which uses the priming charge to drive a small projectile. If the barrel is more than 8" the projectile will slow down on the bore.
    It might chamber .22 short. However, beware the .22 short may be too powerful and result case failure the extractor being blown out sideways.
    6mm Flobert is still available in Europe from RWS.

    Attachment 102935

  9. The Following 2 Members Say Thank You to old rockape For This Useful Post:


  10. #5
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    Yesterday @ 04:14 PM
    Location
    Desert Hot Springs, California
    Posts
    1,053
    Real Name
    Walt Meyer
    Local Date
    03-28-2024
    Local Time
    09:27 AM
    Thread Starter
    Quote Originally Posted by old rockape View Post
    You probably have a training or a Zimmer rifle. Both are for indoor use. It will be chambered for the 6mm Flobert, which uses the priming charge to drive a small projectile. If the barrel is more than 8" the projectile will slow down on the bore.
    It might chamber .22 short. However, beware the .22 short may be too powerful and result case failure the extractor being blown out sideways.
    6mm Flobert is still available in Europe from RWS.

    Attachment 102935
    Thank you, we will look into that!

  11. #6
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-28-2024
    Local Time
    04:27 PM

    PHOTOS AND MEASUREMENTS PLEASE !

    Quote Originally Posted by Singer B View Post
    I have been working on my friend's small rimfire rifle. It is marked "Gecado Suhl" on the barrel with the number "39" marked on the bolt and barrel. The barrel has a small chamber that will not accept a .22 caliber round. The barrel opens up widely after several inches into a diameter of approximately
    .30 caliber. it is a single shot. Can anyone please advise what the caliber would be and why the barrel is sized so strangely? Thanks!
    Well I and others could advise you much more precisely if you would take the trouble to post a photo or two and to measure - even roughly - the length of the narrow section. The reason why will soon become apparent.

    As it is, I can only switch my crystal ball to maximum sensitivity and make a couple of deductions and suggestions from the somewhat fuzzy picture.

    Firstly, what you are looking at is not actually the ballistically effective barrel. It is just a tube to give the external impression of a barrel and mount the sights. The actual barrel is the narrow bit that has been puzzling you.

    It seems to be some kind of "Zimmergewehr" - i.e. indoor rifle. These were basically made in 3 different styles of construction:

    1) Gallery rifles for non-military indoor use, funfairs and the like. Often with a very steep buttstock for shooting in the standing position.

    2) Trainers made ex-factory to be handled and aimed like a military rifle, with a smallbore insert at the rear end, where the cartridge would otherwise have been inserted. In other words, a sub-caliber construction.

    3) One-time full-bore rifles, converted by chambering an rifled insert that looks like the original cartridge case, but has a very short rifled section. The tiddly little cartridge is inserted where the primer would be on a normal case. It would be a Flobert-type cartridge - just primer and projectile, no powder charge. These were popular for home-training with a full-bore rifle in the days when you could still legally pop off a few small-bore shots at a private club or in your cellar. Not today, since (at least over here in Mauserland) they are just as strongly regulated as a full-bore rifle.

    So now it is clear why one needs a couple of photos, and why one need to know the length of the narrow section - the actual barrel!

    Just push in a length of copper wire that has the last couple of mm sufficiently bent to snag on the end of the narrow section, without jamming. Do NOT use steel wire, as the rifling is very fine and easily damaged by something like piano wire! A wire from a scrap piece of solid-cored electrical cable is ideal. With this, you can estimate the length of the small-bore barrel section. If it is much more that about 2" then it is probably fitted as a permanent insert, maybe set up so that it can be removed by unscrewing a threaded ring.

    If it is around 2" - i.e. the length of a full-bore cartridge case - then it is a rifled case and is not intended to be permanent. However, if the thing has been left in the full-bore chamber for years, it may be corroded into place and give the impression of being a permanent insert!

    The small-bore cartridge used with these types of rifle was thus a tiny Flobert-style device, of which there were several options. As you write that it is a rimfire rifle and that 6mm does not fit, then I guess it is probably a 4mm Flobert. Whether it is 1) 2) or 3) of the options mentioned above, can best be shown by PHOTOS !!!

    Photos please!
    Last edited by Patrick Chadwick; 09-21-2019 at 09:57 AM.

  12. Thank You to Patrick Chadwick For This Useful Post:


  13. #7
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    Yesterday @ 04:14 PM
    Location
    Desert Hot Springs, California
    Posts
    1,053
    Real Name
    Walt Meyer
    Local Date
    03-28-2024
    Local Time
    09:27 AM
    Thread Starter
    Quote Originally Posted by Patrick Chadwick View Post
    Well I and others could advise you much more precisely if you would take the trouble to post a photo or two and to measure - even roughly - the length of the narrow section. The reason why will soon become apparent.

    As it is, I can only switch my crystal ball to maximum sensitivity and make a couple of deductions and suggestions from the somewhat fuzzy picture.

    Firstly, what you are looking at is not actually the ballistically effective barrel. It is just a tube to give the external impression of a barrel and mount the sights. The actual barrel is the narrow bit that has been puzzling you.

    It seems to be some kind of "Zimmergewehr" - i.e. indoor rifle. These were basically made in 3 different styles of construction:

    1) Gallery rifles for non-military indoor use, funfairs and the like. Often with a very steep buttstock for shooting in the standing position.

    2) Trainers made ex-factory to be handled and aimed like a military rifle, with a smallbore insert at the rear end, where the cartridge would otherwise have been inserted. In other words, a sub-caliber construction.

    3) One-time full-bore rifles, converted by chambering an rifled insert that looks like the original cartridge case, but has a very short rifled section. The tiddly little cartridge is inserted where the primer would be on a normal case. It would be a Flobert-type cartridge - just primer and projectile, no powder charge. These were popular for home-training with a full-bore rifle in the days when you could still legally pop off a few small-bore shots at a private club or in your cellar. Not today, since (at least over here in Mauserland) they are just as strongly regulated as a full-bore rifle.

    So now it is clear why one needs a couple of photos, and why one need to know the length of the narrow section - the actual barrel!

    Just push in a length of copper wire that has the last couple of mm sufficiently bent to snag on the end of the narrow section, without jamming. Do NOT use steel wire, as the rifling is very fine and easily damaged by something like piano wire! A wire from a scrap piece of solid-cored electrical cable is ideal. With this, you can estimate the length of the small-bore barrel section. If it is much more that about 2" then it is probably fitted as a permanent insert, maybe set up so that it can be removed by unscrewing a threaded ring.

    If it is around 2" - i.e. the length of a full-bore cartridge case - then it is a rifled case and is not intended to be permanent. However, if the thing has been left in the full-bore chamber for years, it may be corroded into place and give the impression of being a permanent insert!

    The small-bore cartridge used with these types of rifle was thus a tiny Flobert-style device, of which there were several options. As you write that it is a rimfire rifle and that 6mm does not fit, then I guess it is probably a 4mm Flobert. Whether it is 1) 2) or 3) of the options mentioned above, can best be shown by PHOTOS !!!

    Photos please!
    I will take the photos tonight when I get home from work and post them tomorrow. I really appreciate your help!

  14. #8
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    Yesterday @ 04:14 PM
    Location
    Desert Hot Springs, California
    Posts
    1,053
    Real Name
    Walt Meyer
    Local Date
    03-28-2024
    Local Time
    09:27 AM
    Thread Starter
    Hi Patrick,

    Here are the photos you asked for. The barrel's overall length is 19.5 inches. I inserted a wood dowel into the muzzle end and measure it when it hit the insert in the barrel. The measurement was 13 inches indicating the insert is approximately 6.5 inches in length. Based upon the photos, it appears the insert is not seated properly based upon the off set of the chamber face. Thanks for the help!

  15. Thank You to Singer B For This Useful Post:


  16. #9
    Contributing Member rcathey's Avatar
    Join Date
    Dec 2012
    Last On
    Yesterday @ 11:56 AM
    Location
    St. Louis, MO Area
    Posts
    1,645
    Local Date
    03-28-2024
    Local Time
    09:27 AM
    I’d betchya this was a 9mm shotgun at one point in time. Sleeved to some sort of 22 (or metric equivalent).

+ Reply to Thread

Similar Threads

  1. Who has one of these? it's a WW1 era 6.5mm, unique bolt action rifle
    By owengun in forum Milsurps General Discussion Forum
    Replies: 5
    Last Post: 06-30-2014, 12:38 AM
  2. Replies: 0
    Last Post: 04-16-2013, 07:27 AM
  3. Mauser KKW ES350, .22LR Bolt-Action Rifle
    By Pirate69 in forum Mauser Rifles
    Replies: 0
    Last Post: 07-30-2012, 08:33 PM
  4. Mauser bolt action rifle prototype (NRA Video)
    By Badger in forum The Screening Room
    Replies: 0
    Last Post: 05-31-2011, 07:01 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks