+ Reply to Thread
Results 1 to 9 of 9

Thread: Indexing new barrel on 1897 take-down

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member M1 C FAN's Avatar
    Join Date
    Apr 2019
    Last On
    07-18-2022 @ 07:21 PM
    Location
    Portland OREGON
    Posts
    180
    Local Date
    03-29-2024
    Local Time
    01:48 AM

    Indexing new barrel on 1897 take-down

    So I purchased a new 20" barrel and Take down extension for a 1897 Winchester and it indexes about 25deg past true. Has anyone used shims to get the timing correct? Or should a small amount be turned off the shoulder of the barrel to get another 3/4 turn?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:49 AM
    Location
    Victoria BC
    Posts
    29,839
    Real Name
    Jim
    Local Date
    03-29-2024
    Local Time
    01:48 AM
    Don't they make, or didn't they make...a variation of the threaded collars that head-space the barrel? They made a number of them that adjusted this problem...and we were just talking about it here.

    When you set back a barrel, you need to do it in complete rotations. You can't do just a smidge with a barrel that's finished and roll marked without things being off TDC. I just did a 760 Remington to correct excess head-space by doing a setback of two threads, which equaled one rotation. Problem gone...after.
    Regards, Jim

  4. Thank You to browningautorifle For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member M1 C FAN's Avatar
    Join Date
    Apr 2019
    Last On
    07-18-2022 @ 07:21 PM
    Location
    Portland OREGON
    Posts
    180
    Local Date
    03-29-2024
    Local Time
    01:48 AM
    Thread Starter
    The issue is when the barrel screws into the Take down extension, not the Takedown extension into the receiver. When the barrel screws into the Take down extension it tightens about 25 deg. past straight up. I have not yet tried the fit of the Takedown extension to the receiver with an adjusting collar.

  7. #4
    Contributing Member rcathey's Avatar
    Join Date
    Dec 2012
    Last On
    03-27-2024 @ 11:56 AM
    Location
    St. Louis, MO Area
    Posts
    1,645
    Local Date
    03-29-2024
    Local Time
    03:48 AM
    What about a stainless steel shim?

    Something like this but of the proper diameter: https://www.brownells.com/rifle-part...prod96012.aspx

    A correct thickness shim (it wouldn't be much) would take up that 25 degrees pretty easy.

    Also check here: https://www.mcmaster.com/shims

  8. #5
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:49 AM
    Location
    Victoria BC
    Posts
    29,839
    Real Name
    Jim
    Local Date
    03-29-2024
    Local Time
    01:48 AM
    Quote Originally Posted by rcathey View Post
    What about a stainless steel shim?
    Quote Originally Posted by M1icon C FAN View Post
    25 deg. past straight up.
    So, headspace will be an issue, don't know how much of one with this particular thing. You'd still need to do a setback, one rotation at least. Then the fittings up front will be out of whack. I doubt the pressures here are serious enough to effect things. You can try a shim and see. Like using stainless washers 1 thousandth each... But that was the whole idea behind the different collars wasn't it? Just screw a new one on and come to TDC with the barrel?
    Regards, Jim

  9. #6
    Legacy Member vintage hunter's Avatar
    Join Date
    Dec 2010
    Last On
    @
    Location
    S.C.
    Age
    56
    Posts
    1,680
    Local Date
    03-29-2024
    Local Time
    04:48 AM
    No shims. I was headed this route years ago but after talking with a gunsmith friend who used to repair and/or cut down guns for customers that were into CAS back in the day and reading up on rebarreling a Winchester 97 TD I changed my mind. Theres way more involved than just screwing one barrel off and the new one on, lots of fitting required to do it right.
    IIRC, when the factory assembled these they'd select a barrel and hand fit extensions until they found one that would hand tighten a couple degrees before TDC. Then it would be tightened using a purpose made tool that supported the extension to avoid distorting it.
    Once that was done they'd fit it to the frame with the indexing sleeve,again trying different ones until the two halves tightened up correctly. There were 3 or 4 different sleeves for the 97 I think, a standard unmarked and three others lettered A, B & C. The difference had to do with either the number of notches or the placement of the notches in relation to the external, interrupted threads. I forget which.
    Next it would need fitting to the chamber ring. If the chamber ring and chamber are misaligned there will be feeding and/or extraction problems, among other things.
    Then it would need headspacing and then....get the picture.
    Ever notice the serial numbers on the extension of TD guns? They look hand stamped dont they? They are, the barrel section wouldn't recieve a s/n until fitting was complete.
    I've most likely left out something as it's been nearly 20 years since I considered rebarreling mine.
    My advice would be to find a smith who's knowledgeable on the workings of these old guns to do the refit.
    Last edited by vintage hunter; 12-12-2019 at 06:09 PM.

  10. Thank You to vintage hunter For This Useful Post:


  11. #7
    Legacy Member M1 C FAN's Avatar
    Join Date
    Apr 2019
    Last On
    07-18-2022 @ 07:21 PM
    Location
    Portland OREGON
    Posts
    180
    Local Date
    03-29-2024
    Local Time
    01:48 AM
    Thread Starter
    Thank You all. I figured I would need a smith just to tighten the barrel without hurting the extension anyway so I will be talking to a good smith.

  12. #8
    Legacy Member Hcompton79's Avatar
    Join Date
    Nov 2016
    Last On
    03-01-2021 @ 11:10 PM
    Location
    Oxford, MI
    Posts
    110
    Real Name
    Hunter Compton
    Local Date
    03-29-2024
    Local Time
    03:48 AM
    You might want to give Rick Stover at The Cowboy Way a call. He's a semi-retired gunsmith who used to do a lot of work for CAS shooters and is very knowledgeable about the Winchester 1897.

    I had him rework my 1897 and he replaced the chamber ring and take down extension and when I got it back it sure did fit tight. He may also have parts?

    Bottom line is as others have said is that there were variations in the take down extension and one was picked at the factory for the best fit in the receiver, after which the chamber ring needs to be sized accordingly so that there is no gap between it and the end of the barrel.

  13. Thank You to Hcompton79 For This Useful Post:


  14. #9
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Yesterday @ 04:54 AM
    Location
    Brisbane
    Posts
    2,237
    Local Date
    03-29-2024
    Local Time
    06:48 PM
    I vaguely recall that Winchester produced three "generations" of the '97 in fairly short order. The first ones were little more than variants on the black-powder fueled 1893, beefed-up to handle smokeless loads. Apparently it took a bit of "Beta-testing" by the customers to iron out all the fiddly details.

    From what I heard from contacts in the US, when the Chinese, (Norinco), first introduced their '97 "clone", it had many "issues". One assessment was that whoever had supplied them with the "sample" sent over a heavily "pre-loved" early -production gun. This was faithfully copied, warts, worn and damaged parts and all.

    Later ones are allegedly a lot better.

    The serial number on the frame will indicate which variant you have. Note that some '97 examples have no visible serial number. There was some caper involving Sears and Roebuck, among others. Some are simply marked "WRA Co." As others have mentioned, contact a '97 specialist to avoid further frustration.

+ Reply to Thread

Similar Threads

  1. WWI WRA 1897 Trench, barrel swapped with a pipe Wrench?
    By cplstevennorton in forum Military Shotguns
    Replies: 6
    Last Post: 03-03-2019, 06:05 PM
  2. Win. 1897 Riot ???
    By gunsdora in forum Military Shotguns
    Replies: 2
    Last Post: 11-27-2015, 09:30 PM
  3. Looking for an 1897 expert, Please?
    By NORTEXED in forum Military Shotguns
    Replies: 11
    Last Post: 03-25-2011, 08:25 AM
  4. Question for Capt Laidler, indexing No.4 barrels
    By whiterider in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 17
    Last Post: 11-21-2009, 02:46 PM
  5. Barrel indexing on a Garand
    By Maddogkiller in forum Gunsmithing for Old Milsurps
    Replies: 6
    Last Post: 10-24-2009, 06:54 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks