+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18

Thread: converting the Italian Colt cap & ball to cartridge revolvers

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:56 PM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-19-2024
    Local Time
    02:35 AM

    converting the Italian Colt cap & ball to cartridge revolvers

    Back about fourteen or fifteen years ago I found some new smokeless 38 S&W cylinders from a gunsmith. These were part of the old Legal Defender kits sold in Shotgun News to convert your Italianicon Colt to use cartridges. Next step was to fine some incomplete and damaged revolvers at some gun shows. I found an Uberti 1861 Colt missing the cylinder and loading lever and not working, later I found another Uberti 1851 Colt with the cylinder locked and wrench marks in an attempt to rotate it, missing grips and loading lever too.

    I was able to restore these revolvers, making new ejector housings, recoil plates, loading gates plus replacing hands and bolts and making barrel wedges. I ordered brass ejector rod springs and SA mainsprings from EMF. Now these pistols shot alright but there is still the problem of firing a .358 dia bullet down a much larger bore. I decided to use hollow based bullets that I made up with a weight like the original of about 130 grs. these work with light charges of Unique, will try black powder outdoors.Attachment 104387Attachment 104388Attachment 104389Attachment 104390
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. Thank You to RCS For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:35 AM
    Location
    Victoria BC
    Posts
    29,813
    Real Name
    Jim
    Local Date
    03-19-2024
    Local Time
    12:35 AM
    They look pretty good...
    Regards, Jim

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Advisory Panel tiriaq's Avatar
    Join Date
    Oct 2006
    Last On
    Yesterday @ 09:32 PM
    Location
    Central Ontario
    Age
    78
    Posts
    1,074
    Local Date
    03-19-2024
    Local Time
    03:35 AM
    Nicely done!
    I remember those Legal Defender kits being advertised.
    In addition to hollow based bullets, there is the option of heeled bullets, as well as sleeving the barrel to correct .38 cartridge dimensions.
    Anyone interested might want to visit kirstkonverter.com and cartridgeconversion.com.

  7. #4
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:56 PM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-19-2024
    Local Time
    02:35 AM
    Thread Starter

    converting the Italian Colts to cartridge

    I know about the excellent Kirst products and have a new Kirst cylinder in 38 cal for the Colt 1851 should I find another incomplete revolver. S&S Firearms use to carry the line
    of heeled bullets but long discontinued the molds.

    The 1861 Colt has a slightly larger frame and when I made the recoil late, I had to make the firing pin and bushing off-set. Also had to make a gage to align the firing pin hole to the center of the primer and the cylinder to the barrel breech. It worked out on the second attempt (photo of the recoil plate of the 1861 revolver). The load gates were made from a round piece of stock then cut outAttachment 104400Attachment 104401Attachment 104402Attachment 104403

  8. #5
    Advisory Panel tiriaq's Avatar
    Join Date
    Oct 2006
    Last On
    Yesterday @ 09:32 PM
    Location
    Central Ontario
    Age
    78
    Posts
    1,074
    Local Date
    03-19-2024
    Local Time
    03:35 AM
    I'm in the process of setting up a Pietta '51 in both .38 and .45, using Kirst parts. Going to try HBWCs in the .38, see how they work, before deciding about installing a liner. Have a piece of liner on hand, if needed. The HBWCs are an smooth push fit in the .36 barrel, so with the hollow base, they should engage the rifling nicely.
    Made a replacement ejector assembly for a hand made single action revolver (a Selby Webb .22). Folks might not appreciate there is a bit more to making one of these than meets the eye.
    Acquired a basket case Centennial Arms 1860 a while back. This is one of the first repro percussion revolvers to reach the market, back in the '60s. It had a ruined cylinder pin, so I had to make one. Interestingly, the threads are Imperial. Started with a die makers bolt, machined it to fit the cylinder, etc. Cutting the slot for the wedge was the fun part.

  9. #6
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:56 PM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-19-2024
    Local Time
    02:35 AM
    Thread Starter

    cartridge conversions

    I would recommend using hollow based bullets first in any of the conversions even if you have to make the hollow base yourself. I have had good results in my 1861 and 1851 conversions.

    I have also used hollow base 452 dia lead in my S&W 1915 that was in 455 but rechambered to 45 Colt. Also made a shorter 45 Colt cartridge case tooAttachment 104438Attachment 104437

  10. #7
    Legacy Member pocketshaver's Avatar
    Join Date
    Dec 2018
    Last On
    09-23-2020 @ 04:17 AM
    Location
    usa
    Posts
    229
    Local Date
    03-19-2024
    Local Time
    02:35 AM
    Anyone ever try to do the original method of slicing up the factory cylinder, and pinning/screwing a plate on the rear to make the thickness correct and then drilling through the whole thing?
    Remember an issue of old west guns that had a short talk about a modern company post 2010 that did that for a special Patterson edition

  11. #8
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:56 PM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-19-2024
    Local Time
    02:35 AM
    Thread Starter
    You are correct, back in the post Civil War period when they (gunsmiths and Colt factory) started the cartridge conversions, they cut off the rear
    of the cylinder and installed a recoil plate. Some had firing pins in the recoil plate while other conversions used the hammer firing pin. Your idea
    is good only if you use black powder in the cartridge (example 38 Colt ) If someone chambers a smokeless cartridge in the repro black
    powder cylinder it is not strong enough for sustained shooting. That is why I used the best smokeless cylinders available as both black and
    smokeless powder can be used

  12. #9
    Legacy Member pocketshaver's Avatar
    Join Date
    Dec 2018
    Last On
    09-23-2020 @ 04:17 AM
    Location
    usa
    Posts
    229
    Local Date
    03-19-2024
    Local Time
    02:35 AM
    thing is, the company in the 2010 + who did that Patterson conversion I read about, used the Italianicon percussion cylinders and made no specific requirements in regards to ammunition or not.

  13. #10
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:56 PM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-19-2024
    Local Time
    02:35 AM
    Thread Starter
    The Patterson conversion proof marks would indicate black powder or smokeless powder

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. early 30-40 fluted dummy and ball cartridge
    By RCS in forum Krag Rifles
    Replies: 0
    Last Post: 04-09-2016, 10:09 AM
  2. Which cartridge are the civilian Webley .38 revolvers sighted for?
    By Colonel Enfield in forum Other Military Service Pistols and Revolvers
    Replies: 15
    Last Post: 09-17-2014, 12:01 PM
  3. Lake City Cartridge, Caliber .30, M2, Ball
    By The Wizard in forum Ammunition and Reloading for Old Milsurps
    Replies: 9
    Last Post: 04-22-2013, 02:17 AM
  4. Historical Question: Transition from M1 Ball to M2 Ball Ammo
    By P-07ShortLee in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 9
    Last Post: 11-21-2010, 09:32 PM
  5. Working Colt's Model 1877 Double-Action Revolvers
    By Newsfeed Hound in forum The Watering Hole OT (Off Topic) Forum
    Replies: 0
    Last Post: 08-18-2010, 06:40 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks