+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12

Thread: M1903 barrel change/rear sight base

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member phh's Avatar
    Join Date
    Feb 2020
    Last On
    12-01-2020 @ 05:46 PM
    Location
    France
    Posts
    5
    Local Date
    03-28-2024
    Local Time
    05:20 AM

    M1903 barrel change/rear sight base

    Hello everybody my name is Paul, I live in Franceicon and I'm fond of Us Firearms.

    I just bought a M1903 built in 1942. The barrel is definitely dead. So I have to change it and I have a few questions about that, in particular about the rear sight base. I purchased a brand new criterion 4 grooves barrel.

    In my readings I understood that :

    1) The rear sight base is maintained by two pins. One is perpendicular to the barrel preventing the base to go forward and back, and the other is parallel to the barrel preventing the base to turn.

    2) I first have to unscrew and remove the old barrel with the rear sight base on it and then I can remove (try to remove) the base from the old barrel.

    My problems and questions :

    1) Is the barrel very hard to unscrew ? I remember of a P17 barrel in which I had to make a relief cut but on this M1903 it's impossible because of the rear sight base.

    2) For the moment I can't locate the first pin. I've got an idea where it is but it's just an idea... Am I right ?



    3) Any tip to remove the base ? Forward ? backward ? Heating ? I must save it because it will be very hard to find another one.

    Thanks in advance for your answers.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by phh; 02-08-2020 at 12:34 PM.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member butlersrangers's Avatar
    Join Date
    Nov 2009
    Last On
    03-26-2024 @ 09:38 PM
    Location
    S.E. Michigan, U.S.A.
    Posts
    737
    Local Date
    03-28-2024
    Local Time
    06:20 AM
    'phh' - You did locate the cross-pin. Drive it Left-Side of rifle to Right.

    A scrap metal piece that will fit in the sight-base, (where the 'movable-base' traverses), will give you a surface to pound on. This protects the delicate base pieces from being bent or broken. Some heat on the 'collar' can help loosen it from the barrel, before you dive it forward.

    You can do this with the barrel still on the action. (The second pin will just go forward with the sight-collar. The pin may be on the right or left. In my opinion it is not necessary in a rebuild. A little Epoxy will work just as well).

    1903 barrels are easier to remove than M-1917 barrels.

    Good Luck on your noble project!
    Last edited by butlersrangers; 02-08-2020 at 01:04 PM.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member phh's Avatar
    Join Date
    Feb 2020
    Last On
    12-01-2020 @ 05:46 PM
    Location
    France
    Posts
    5
    Local Date
    03-28-2024
    Local Time
    05:20 AM
    Thread Starter
    Ok, thank you very much. Is there a way to make this pin appear much to see better where I must pound ? Right now it seems to be part of the sight base. Sanding ?

  6. #4
    Legacy Member butlersrangers's Avatar
    Join Date
    Nov 2009
    Last On
    03-26-2024 @ 09:38 PM
    Location
    S.E. Michigan, U.S.A.
    Posts
    737
    Local Date
    03-28-2024
    Local Time
    06:20 AM
    Yes, sanding or polishing off a bit of the finish will make the beveled end of the pin a bit more visible.

    Lightly center-punching the left-end of the pin will help prevent the Drive-Punch from slipping.

    This will allow more force to be directed in a straight line. (You can even 'drill' slightly into the end of the pin, so your Punch is easily controlled).

  7. #5
    Legacy Member phh's Avatar
    Join Date
    Feb 2020
    Last On
    12-01-2020 @ 05:46 PM
    Location
    France
    Posts
    5
    Local Date
    03-28-2024
    Local Time
    05:20 AM
    Thread Starter
    Thanks , I'll try it.

  8. #6
    Legacy Member m1903rifle's Avatar
    Join Date
    Mar 2009
    Last On
    03-04-2024 @ 02:45 PM
    Location
    Knoxville,TN
    Age
    79
    Posts
    376
    Local Date
    03-28-2024
    Local Time
    05:20 AM
    One of the gunsmiths who frequents this forum ( chuckindenver ), recommends removing the barrel first. Once you have removed the transverse pin, and the front sight ( if you plan on reusing it ), remove the moveable ladder sight. Then, holding the barrel at the sight base with a good heavy leather glove, strike the muzzle of the rifle on a hard surface until the sight base comes off. Of course the barrel muzzle will be ruined in the process, and therefore should only be used when the barrel is "trashed".

  9. Thank You to m1903rifle For This Useful Post:


  10. #7
    Contributing Member Doco overboard's Avatar
    Join Date
    Jun 2015
    Last On
    Yesterday @ 04:48 PM
    Location
    Delmarva Peninsula
    Posts
    452
    Real Name
    Brian Stiles
    Local Date
    03-28-2024
    Local Time
    06:20 AM
    Quote Originally Posted by phh View Post
    Ok, thank you very much. Is there a way to make this pin appear much to see better where I must pound ? Right now it seems to be part of the sight base. Sanding ?
    Yes, once you have polished the area where the pin resides, a touch of cold blue will make it show up very well. Once your barrel is off, find a scrap pipe section that is nearly the same diameter as the sight collar and turn it to the same inside diameter of the inner collar radius to drive it on.
    As the collar is being driven on-you can then slightly "steer" with a twisting motion in your hand the collar to match the index marks on the receiver once it's nearly home. With the barrel installed by driving the collar right up to the face of the receiver a nice transition can be had without an unsightly line or seamless transition between the two parts.

  11. #8
    Legacy Member phh's Avatar
    Join Date
    Feb 2020
    Last On
    12-01-2020 @ 05:46 PM
    Location
    France
    Posts
    5
    Local Date
    03-28-2024
    Local Time
    05:20 AM
    Thread Starter
    Ok. I've localized the pin. . Tried to pound on it with a little pin remover, but for the moment nothing moves on the other side. It's gonna be a hard job...

    This thing hasn't been made to be stripped.

  12. #9
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    03:20 AM
    You need to use a proper hammer and drift for this, a light tack hammer and nail won't do it. That's why most have a gunsmith do this.
    Regards, Jim

  13. #10
    Legacy Member phh's Avatar
    Join Date
    Feb 2020
    Last On
    12-01-2020 @ 05:46 PM
    Location
    France
    Posts
    5
    Local Date
    03-28-2024
    Local Time
    05:20 AM
    Thread Starter
    Got it.

    Waouh... (eureka, hourra )



    Now, unscrew the barrel.... Au gunmith will do
    Last edited by phh; 02-09-2020 at 01:55 PM.

  14. Thank You to phh For This Useful Post:


+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. K98 rear sight scale and actual change in MOA
    By mac1911 in forum Mauser Rifles
    Replies: 3
    Last Post: 07-06-2017, 08:20 AM
  2. Issue with front sight base alignment with rear sight
    By RBruce in forum M16A2/AR15A2 Rifles
    Replies: 2
    Last Post: 03-27-2015, 11:29 AM
  3. M1903 front sight base.
    By nashorn in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 1
    Last Post: 07-14-2009, 12:03 AM
  4. Rear sight base
    By Elime in forum M1 Garand/M14/M1A Rifles
    Replies: 3
    Last Post: 03-16-2009, 06:41 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks