+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: Need Advice Getting a Neglected M1917 Sporter into Shape.

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member LukeM's Avatar
    Join Date
    Mar 2020
    Last On
    03-27-2020 @ 07:56 PM
    Location
    Seattle, WA, U.S.A.
    Posts
    3
    Local Date
    03-28-2024
    Local Time
    03:01 PM

    Need Advice Getting a Neglected M1917 Sporter into Shape.

    Hello everyone, hope you're all doing well. I've a new-to-me Eddystone 1917 that needs some TLC to get up and running. I'm not trying to make a collector's item, just want a safely functioning rifle. I think the last time it was fired was twenty years ago, and it's been bouncing around the family without anyone taking care of it.

    The stock that's on it is the one it came with when it was bought in the Fifties, and there are no major cracks in it that I can see. It looks like there was something for a sling on the underside of the butt-stock, but nothing up forward. The original rear sight is gone, and an adjustable open sight is attached to the barrel. The barrel has five rifling grooves so I think it's the original. There is light rust in spots all over the place. The action cycles fine.

    The first thing I did with the barrel was run a copper bore brush though it, then blew some air down it. Out came a small orange cloud, so I went to town with patches and solvent. The patches come out clean now and the bore looks smooth when I look down it with a light on the other end but shining a light into the muzzle still shows a faint orange. I don't know how well the chroming on these old barrels is expected to age. The muzzle itself doesn’t have any visible damage, and I ran a straightedge along the barrel. Didn’t find any bulges or cracks. About cracks, are the rumors about cracked receivers debunked, or should I be concerned?

    So, from what I understand the rifle should still be safe to shoot, since it hasn’t been used enough to lose headspacing, though I don’t know how well the wood stock will have aged strength-wise. Do hardwood stocks last over the decade, or should I look into an aftermarket stock like one from Richards Microfit Stocks? As for needing a new barrel, is the only real way to know if I need one is to take it to the range? I’m not sure how easy it will be for me to judge the rifle’s accuracy with the open sights. I've always been into guns, but I don’t have a huge amount of experience actually shooting them.

    Also, what recommendations does anyone have for refinishing the rifle? I think if the barrel's lining is intact, getting the rifle parkerized would be good enough. Is there any risk to the wood if the receiver is removed by a professional? And any competent gunsmith will know how to replace the barrel if needed, with the relief cuts and such? The top of the receiver has been machined into a shallow arc. Is that the Remington Model 30 style? For scope mounts and things like that?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    03-29-2024
    Local Time
    12:01 AM
    Quote Originally Posted by LukeM View Post
    but shining a light into the muzzle still shows a faint orange.
    That could be heavy copper deposits. Can be removed with a suitable solvent. But Jim has said it all - ACWOTAM to try to turn it back into a military configuration M1917.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member bros's Avatar
    Join Date
    Jan 2011
    Last On
    Yesterday @ 04:03 AM
    Location
    yukon
    Posts
    272
    Local Date
    03-28-2024
    Local Time
    03:01 PM
    I wouldn't put any $$ into that one. Here in Canadaicon you can buy a very decent P14 sporter that's not Bubba'ed other than the stock for a $225-275 can. I would think in the US you could do the same if not better.
    That one's like trying to make a "silk purse out of a pig's ear". If it was mine at best it would fall into "truck gun category".
    Unless if it has sentimental value like grandpa's old war horse..........

  6. #4
    Legacy Member LukeM's Avatar
    Join Date
    Mar 2020
    Last On
    03-27-2020 @ 07:56 PM
    Location
    Seattle, WA, U.S.A.
    Posts
    3
    Local Date
    03-28-2024
    Local Time
    03:01 PM
    Thread Starter
    It does have a bit of sentimental value. It was one of the first things my Dad's foster father bought when he emigrated from Italyicon to Canadaicon after the War. Just getting the steel refinished would be enough. The barrel not being chromed isn't much of an issue with modern non-corrosive ammo as long as the bore is kept cleaned and oiled, right?

  7. #5
    Contributing Member mmppres's Avatar
    Join Date
    Mar 2014
    Last On
    03-22-2024 @ 08:15 AM
    Location
    butler pa
    Age
    58
    Posts
    1,082
    Real Name
    mike
    Local Date
    03-28-2024
    Local Time
    06:01 PM
    Take the barrel action out of the stock. Scrub the bore with a very good solvent. Get some Oxyblue from Brownells . Re. due your metal. The stock. Scrub down with BLOicon, a few times after you put a new reciol pad on it. Put all back together an have fun shooting a family heirloom. JMO

  8. #6
    Legacy Member oldfoneguy's Avatar
    Join Date
    Oct 2015
    Last On
    Today @ 05:19 PM
    Location
    long island, ny
    Posts
    561
    Real Name
    Bill
    Local Date
    03-28-2024
    Local Time
    05:01 PM
    I converted my 1917 sporter into a faux US Model 1918 the greatest sniper rifle that never was. I added a weaver detachable side mount with a weaver 3x scope and Garandicon cheek piece.
    I've owned this for 36 years and it's been through many changes but in full military stock is the most accurate configuration it's ever had.
    Edit, have been trying to add pictures but the site isn't letting me.
    Last edited by oldfoneguy; 03-26-2020 at 08:33 PM.

  9. #7
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 06:54 AM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,392
    Real Name
    Daan Kemp
    Local Date
    03-29-2024
    Local Time
    12:01 AM
    Due to the sentimental value I agree with mmppres post #6. Take the metal out of the wood. Clean both properly. Replace the horrible sights with something better. Reblue the metal. Replace the pad with a new and better one. Re-oil the wood. Put it all together again.

    Enjoy the family heirloom for another 70 years. Just some oil every now and then, and lots of shooting often.

  10. #8
    Legacy Member Mk VII's Avatar
    Join Date
    Dec 2008
    Last On
    03-20-2024 @ 07:30 PM
    Location
    England
    Age
    62
    Posts
    1,406
    Real Name
    James West
    Local Date
    03-28-2024
    Local Time
    10:01 PM
    Could it be one of these? .303, I know but they seem to have done .30s as well. Think I see a Canadianicon ownership mark on the receiver ring.



  11. #9
    Advisory Panel Surpmil's Avatar
    Join Date
    Feb 2008
    Last On
    @
    Location
    West side
    Posts
    4,651
    Local Date
    03-28-2024
    Local Time
    03:01 PM
    Quote Originally Posted by Mk VII View Post
    Could it be one of these? .303, I know but they seem to have done .30s as well. Think I see a Canadianicon ownership mark on the receiver ring.

    https://www.milsurps.com/images/impo...1catP141-1.jpg
    Good spot. So undoubtedly one of the many rifles brought up from the USAicon as Lend Lease in WWII. AFAIK none of those .3006 rifles were taken to the UKicon or used there by Canadian troops, so probably the chop was done here in North American post-war.

    No sign of the action being drilled and tapped as per the advert?

    OP: I think what you've got is a decent quality action you could rebarrel and build something out of if your sentimental attachment to it is strong enough; otherwise it's a "parts car" for someone else.

    All manner of magnums were built on these actions, although some may have been re-heat treated in the process, as there were issues with some early rifles, Eddystones in particular.
    Last edited by Surpmil; 03-27-2020 at 05:29 PM. Reason: "Some"
    “There are invisible rulers who control the destinies of millions. It is not generally realized to what extent the words and actions of our most influential public men are dictated by shrewd persons operating behind the scenes.”

    Edward Bernays, 1928

    Much changes, much remains the same.

  12. #10
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 06:54 AM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,392
    Real Name
    Daan Kemp
    Local Date
    03-29-2024
    Local Time
    12:01 AM
    The calibre seems to be more than sufficient, be it 303 or 30-06.

    Doesn't look like the front sight had a hood and the milling of the ears was done locally. Then the pad. Probably saw the BSA ad or a real one and adapted his rifle.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. M1917 Winchester Sporter Extractor Help
    By 040x in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 11
    Last Post: 01-12-2012, 07:21 PM
  2. Need Advice on a US Model 1917 Eddystone Sporter
    By Cajun72 in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 2
    Last Post: 01-13-2011, 05:15 PM
  3. Newbie Here with M1917 Sporter Question
    By my05hammer in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 18
    Last Post: 09-14-2010, 11:10 PM
  4. This weeks purchase: M1917 sporter
    By M1Riflenut in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 18
    Last Post: 11-17-2009, 11:15 AM
  5. M1917 Woes and Advice
    By Nugilum in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 17
    Last Post: 06-17-2009, 11:54 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks